Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Tow-Pro Wiring Kit Fitting Instructions Suitable for: Holder Colorado / Colorado 7 Kit Part No: TPWKIT-002 Accessory Kit Estimated Fitting Time: 120 Minutes FI11736 Page 01 of 13 © 2018 Issue: 3 Date: 14/08/2018
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 General Notes • Read through the fitting instructions before installation of the accessory. Install the accessory following the fitting instructions. Failure to do so may cause damage to the vehicle or the accessory. • Ensure all recyclables, discarded vehicle accessory components and packaging are recycled following local recycling regulations. • It is always recommended that this accessory is fitted by a qualified automotive Technician.
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Wiring Diagram FI11736 Page 03 of 13 © 2018 Issue: 3 Date: 14/08/2018
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 1 Important Always refer to the vehicle’s Workshop Manual when removing vehicle components. • Note down all clock and radio settings. • In the engine bay, disconnect and isolate the negative battery terminal. 1 • Remove the LHS front scuff plate (1) and dislodge the rubber door seal (2). 2 Step 2 • Remove the LHS kick panel trim (1) by releasing the screw or plastic nut (2).
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 4 Note - this step is not required for the Colorado 7: • Remove the four phillips head screws (1) and remove the inner glove compartment trim (2). 2 1 1 1 1 Step 5 • Dislodge the gear shift surrounding trim (1). • Disconnect the connectors (2) from behind. 2 1 1 Step 6 • Secure the Brake Controller ECU (1) onto the Brake Controller Bracket (2) using supplied M4 Screws (3) M4 Spring Washer (4) and M4 Flat Washers (5).
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 7 • In the glove compartment cavity, remove the vehicle 13mm bolt (1). • Secure the Brake Controller bracket assembly (2) to the vehicle using the existing stud (3), the supplied M8 Nut (4) and M8 Washer (5). 1 3 5 4 • Secure the Brake Controller bracket assembly (2) in place using the previously removed 13mm bolt (1). Important Refer to workshop manual for recommended torque specifications.
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 10 • Insert the supplied Switch Insert (1) into the vacant cavity on the gear shift surround trim (2). • Insert the Electric Brake Switch (3) into the Switch Insert (1) from behind. • Fasten the supplied Nut (4) locking the Electric Brake Switch (3) to the Switch Insert (1). Torque the Nut (4) to 0.8Nm. • Rotate the shaft (5) full anti-clockwise and fit the knob (6) to the shaft (5) with “0" pointing upwards as shown below.
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 13 • In the LHS front wheel arch, remove the two T20 torx screws (1), five scrivets (2) and the 10mm bolt (3). 6 • Release the three T20 torx screws (4) and remove the mudguard (5). • Remove the wheel arch lining (6) and the foam support. 2 4 2 1 2 5 2 4 5 Step 14 • In the LHS front wheel arch area, remove the vehicle grommet (1).
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 16 • Connect the 4-way Connector (1) from the Electric Brake Harness to the Brake Controller ECU (2). 2 1 Step 17 • From under the engine bay, route the Electric Brake Harness (1) (BLUE, RED & RED/WHITE wires) along the top of the chassis rail towards the rear of the vehicle. • Secure harness at every 300mm using supplied 900mm Cable Ties.
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 19 • Continue routing the Electric Brake Harness (1) above the rear LHS wheel arch liner. 1 • Cable tie to the existing vehicle harness. Step 20 • Route the Electric Brake Harness (1) across the rear bumper towards the trailer socket head. • Secure the Electric Brake Harness at every 300mm using the supplied 900mm Cable Ties. 1 Step 21 • Remove the ‘BLUE’ wire (1) from the trailer wiring harness socket head (2).
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 22 • Locate ‘RED’ wire (1) on the trailer wiring harness socket head. • Cut the wire 150mm from the base of the socket. 150mm • Remove the cut ‘RED’ wire (1) from the trailer socket. Pin No.
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 Step 25 • Reconnect the engine bay negative battery terminal. • Test the operation of the Tow-Pro system as per the Tow-Pro user manual. • Dispose of any parts not used from the fitment. Important Secure all harnesses to the vehicle using the supplied cable ties. Refit all removed parts and secure all fasteners to Service Manual torque specifications.
Suitable for: Holden Colorado / Colorado 7 Kit Part No: TPWKIT-002 13 FI11736 © 2018 Issue: 3 Date: 14/08/2018
