BCDC Mounting Bracket SUITABLE FOR Mitsubishi Triton MR Diesel (2019 – On) Mitsubishi Pajero QE/QF (2019 – On) BCDCMB-009
THE BCDC MOUNTING BRACKET The REDARC BCDC Mounting Bracket is designed to install your BCDC in the cool airflow at the front of your vehicle, away from high temperature areas for maximum performance. The BCDC Mounting Bracket is constructed from durable stainless steel and has been designed to fit existing mounting points in your vehicle for ease of installation. This manual outlines installation of the BCDCMB-009 mounting bracket in the Mitsubishi Triton MR Diesel or Mitsubishi Pajero QE/QF.
KIT CONTENTS A B REF C D E PART DESCRIPTION F QTY A BCDCMB-009 BCDC Mounting Bracket 1 B M6 × 20 Hex Bolt 1 C M6 × 12 Pan Head Bolt 4 D M6 Nylon Locking Nut 4 E M6 Flat Washer 5 F M6 Spring Washer 1 YOU WILL ALSO NEED: For this installation, the listed items and tools (or their equivalents) are required.
COMPLETED INSTALLATION The installed BCDCMB-009 Mounting Bracket locates on the passenger side of the radiator. INSTALLATION STEP 1 Remove the 11 clips from the upper plastic shroud. To do this, unscrew the centre before pulling upwards.
INSTALLATION STEP 2 4 × M6 × 12 Pan Head Bolt 4 × M6 Flat Washer 4 × M6 Nylon Locking Nut Fit the BCDC unit to the Mounting Bracket using the supplied M6 hardware using a #3 Phillips screw driver and a 10 mm socket wrench or equivalent.
INSTALLATION STEP 3 (OPTIONAL) It is not necessary to remove the grille to complete the BCDC installation, however if installing additional accessories at the same time, removing the grille may be helpful. To do this, remove the two partially concealed clips located at each end of the grille before lifting the grille away from the bumper. STEP 4 Remove the 3 vehicle fasteners as shown (1 × bolt and 2 × nuts).
INSTALLATION STEP 5 1 × M6 × 20 Hex Bolt 1 × M6 Flat Washer 1 × M6 Spring Washer Fit the BCDC bracket. Return the 3 vehicle fasteners (1 × bolt and 2 × nuts) removed in Step 4 to their original locations. Fix the top left of the bracket using the remaining supplied M6 hardware. STEP 6 To complete the installation, use a suitable REDARC Fuse Kit and follow the instructions as per the BCDC Instruction Manual.
INSTALLATION STEP 7 In order to view the BCDC display panel LEDs, a slot must be cut out of the plastic panel before it is refitted to the vehicle. 1. 2. 3. 4. 5. 6. Cut out the template along the solid black line. Place template with the red arrow towards the engine. Align the template to the plastic panel. Mark hole centres and carefully drill out the ends of the slot using a 12 mm (15⁄32") drill bit. Using a sharp utility knife, carefully cut out the plastic section between the drilled holes.
NOTES 9
NOTES 10
TWO YEAR PRODUCT WARRANTY Over the last three decades our company has established a reputation as the power conversion specialist. A 100% Australian-owned company, we have met the needs of customers in transport and other industries through exciting, innovative thinking.
FREE TECHNICAL ASSISTANCE For product and technical support contact your regional distributor, call our head office between 8:00 a.m. to 5:30 p.m. Australian Central Standard Time, Monday to Friday, or send us an e-mail. Australia (and other Global regions) power@redarc.com.au www.redarc.com.au +61 8 8322 4848 New Zealand power@redarcelectronics.co.nz www.redarcelectronics.co.nz +64 9 222 1024 North America power@redarcelectronics.com www.redarcelectronics.
