Product Card

Sensors and accessories
There are a range of mounting solutions as well as an enhanced lighting controller to dim the gauges to match your vehicle’s instrument panel lighting.
There is also an adaptor to fit the 12 volt gauges to a 24 volt vehicle.
Optional sensors
Code Sensor type For use with Description
GS-AMPS Current G52-VA, G52-VVA,
G52-BEA, G52-TA
The REDARC Hall Effect current sensor is an electronic device which is designed to measure the current flowing
in a circuit and output the value of that current as a voltage signal. (i.e. can monitor the amount of current to or
from your main or auxiliary battery). It is a high performance, compact cable mounted current sensor suitable for
installation into rugged environments where a fully sealed product is required to assure reliability. This REDARC
device is 100A rated and cannot be damaged by overload.
GS-UT-80 Temperature G52-BET, G52-POT,
G52-PWT, G52-PT,
G52-TTT
An NTC temperature sensor encased in a plastic housing for measuring cabin, fridge or outside temperature.
Temperature range is -20~+80°C and is supplied with a 6 metre extension cable to connect to your REDARC
gauge.
GS-UT-120 Temperature G52-BET, G52-POT,
G52-PWT, G52-PT,
G52-TTT
An NTC temperature sensor in a metal copper housing with 6mm diameter mounting hole. Temperature range is
-20~+120°C and it is supplied with a 6 metre extension cable to connect to your REDARC gauge.
GS-OWT1-4 Temperature G52-BET, G52-POT,
G52-PWT, G52-PT,
G52-TTT
A coolant or oil temperature sensor with a 1/4 NTP thread that is designed to measure from -20~ +170°C.
It is supplied with 3 metre extension cable to connect to your REDARC gauge.
GS-OWT1-8 Temperature G52-BET, G52-POT,
G52-PWT, G52-PT,
G52-TTT
The REDARC GS-OWT1-8 is a coolant or oil temperature sensor with a 1/8 NTP thread that is designed to measure
from -20~ +170°C. It is supplied with 3 metre extension cable to connect to your REDARC gauge.
GS-P-150 Oil pressure G52-BEP The REDARC GS-P-150 is a 150psi oil pressure sensor with a 1/8 NPT thread. It is supplied with wiring harness for
connection to your REDARC gauge.
Optional accessories
Code Name Description
GA-ELC Enhanced lighting controller The REDARC enhanced lighting controller is designed to enhance the lighting of your REDARC gauge. It is to be
used when you do not have a dimming circuit to connect to your gauge or when the dimming circuit in your vehicle
does not dim the REDARC gauge to your liking. The enhanced lighting controller also allows you to program the
night-time brightness and colour of your REDARC gauges, including dimming if connected to a dash dimmer. Once
programmed your gauge will change colour when turning on your park lights and back to a day light colour when
you turn them off. It is also 24 volt capable and only one is required for a set of REDARC gauges.
GA-2412V 24-12V adaptor The REDARC 24 volt to 12 volt adaptor must be used to connect your REDARC gauge to a vehicle with a
24 volt ignition and lighting supply. All REDARC gauges must operate from a 12 volt power supply. When
used with G52-VA and G52-VVA, the gauges can only measure 12volt batteries.
GH-CUP Mounting cup The REDARC mounting cup is a black plastic mounting cup that fits one REDARC 52mm gauge. It is supplied
with mounting screws and strong double sided mounting tape.
GH-MP1 Single gauge
mounting panel
The REDARC mounting panel is a black aluminium mounting panel suitable for one REDARC 52mm gauge.
It is supplied with mounting screws.
GH-MP2 Double gauge
mounting panel
The REDARC mounting panel is a black aluminium mounting panel suitable for up to two REDARC 52mm gauges.
Itis supplied with mounting screws.
GH-MP3 Triple gauge
mounting panel
The REDARC mounting panel is a black aluminium mounting panel suitable for up to three REDARC 52mm gauges.
It is supplied with mounting screws.
GMC-2.5 2.5” muffler clamp The REDARC muffler clamp comes with a maximum 2.5” opening. It has been designed to mount the
REDARC EGTprobe.
GMC-3.25 3.25” muffler clamp The REDARC muffler clamp comes with a maximum 3.25” opening. It has been designed to mount the
REDARC EGT probe.
GMC-4.2 4.2” muffler clamp The REDARC muffler clamp comes with a maximum 4.2” opening. It has been designed to mount the
REDARC EGT probe.
GMC-5.5 5.5” muffler clamp The REDARC muffler clamp comes with a maximum 5.5” opening. It has been designed to mount the
REDARC EGT probe.
GA-COMP1-4 1/4” thread compression fitting 1/4” thread compression fitting with mild steel weld-in bung. Replaces the 1/8” thread fitting supplied
with the gauge.
Want to know more?
Scan this QR code with
your smartphone to go to
the Redarc website
Australia
Phone [phone]
Fax [phone]
International
Phone [phone]
Fax [phone]
REDARC Electronics
ABN 77 136 785 092
23 Brodie Road (North)
Lonsdale, South Australia
Australia 5160
[e-mail]
Details and specifications are subject to change without notice. 4586-150605
Copyright © 2015 REDARC Electronics Pty Ltd. All rights reserved.
Visit redarc.com.au for more information.
REDARC gauges are available at your
nearest auto electrician or 4WD specialty
store.
®