RED 3-AXIS LENS CONTROL SYSTEM O P E R AT I O N G U I D E W. M . D . | T. H . C . | L e n s C o n t r o l M o t o r RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E TABLE OF CONTENTS Disclaimer 3 Copyright Notice 3 Trademark Disclaimer 3 Compliance Statements 3 Safety Instructions 5 Battery Storage and Handling 6 Shipping Disclaimer 6 Chapter 1: 3-Axis System Overview 7 Introduction 7 3-Axis System Components 8 Additional Resources 9 Chapter 2: 3-Axis System Launch Sequence 10 Recommended Equipment 10 Prepare the Camera 11 Install the 3-Axis System 11 Connect the 3-Axis System 13 Configure the 3-Axi
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E DISCLAIMER RED has made every effort to provide clear and accurate information in these installation instructions, which are provided solely for the user’s information. While thought to be accurate, the information in this document is provided strictly “as is” and RED will not be held responsible for issues arising from typographical errors or user’s interpretation of the language used herein that is different from that intended by RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E JAPAN STATEMENTS This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. your nearest designated collection point.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E SAFETY INSTRUCTIONS DO NOT use the system or accessories near water. Avoid exposing your system to moisture. The system is not waterproof, so contact with water could cause permanent damage to the system as well as electric shock and serious injury to the user.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E BATTERY STORAGE AND HANDLING WARNING: Failure to read, understand, and follow these instructions may result in overheating, chemical leakage, smoke emission, fire, or other potentially harmful results. Always follow proper battery handling and storage practices. Improper handling and/or failure to abide by proper storage instructions may cause permanent damage to batteries, or degrade charge capacity.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 01 3-AXIS SYSTEM OVERVIEW INTRODUCTION The RED 3-Axis Lens Control System is a versatile and highly accurate wireless lens control system. Use the RED ® Lens Control Motor, RED ® Tactical Hand Controller (T.H.C.), RED ® Wireless Motor Driver (W.M.D.), and related RED accessories to configure a low-profile lens control system for your camera rig. This guide provides setup and operation instructions for the RED Lens Control Motor, T.H.C., W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 3-AXIS SYSTEM COMPONENTS RED offers the following RED 3-Axis Lens Control System components individually, enabling you to customize your lens control setup. For more information, visit the RED Store at www.red.com/store. ITEM PART NUMBER RED 3-Axis Lens Control System 760-0147 RED ® W.M.D. (Wireless Motor Driver) 790-0414 RED T.H.C. (Tactical Hand Controller) 790-0413 RED ® Lens Control Motor 760-0146 RED ® Lens Drive Gear M 0.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E ADDITIONAL RESOURCES The following resources offer additional information about RED, the DSMC ® system, and the RED community: RED.com: Check the official RED website for latest information about RED products. RED Learn Articles: RED offers in-depth technical articles about RED cameras, post-production, and digital cinematography. RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 02 3-AXIS SYSTEM LAUNCH SEQUENCE This section offers condensed installation and operating instructions to help you get started using the RED 3-Axis Lens Control System. For more detailed information on specific components, please refer to the respective chapter in this guide. WARNING: The DSMC ® BRAIN ® must be powered off during any installation process.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E PREPARE THE CAMERA 1. Install a mounting platform for the W.M.D. (Example: DSMC Tactical Cage or Tactical Right Plate) 2. Install a support rod system. (Example: DSMC Modular Assault Plate or Quick Release Platform) 3. Install 15mm or 19mm support rods. INSTALL THE 3-AXIS SYSTEM These instructions provide installation steps using a tactical cage or other cheeseplate. For more information and other installation methods, go to “Mount the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E E. Tighten the thumbscrew until hand tight. WARNING: DO NOT OVERTIGHTEN. 2. Install the RED Lens Control Motor Mounting Bracket. A. Push the lock button on the Lens Control Motor Mounting Bracket to disengage the locking mechanism. B. Slide the dove-tail rail on the Lens Control Motor Mounting Bracket into the dove-tail slot on the Lens Control Motor. C. Release the lock button. D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CONNECT THE 3-AXIS SYSTEM 1. Connect the RED Lens Control Motors. A. Connect the RED W.M.D. Motor Cable to the pivoting connector on each Lens Control Motor. B. Connect the opposite end of the LENS CONTROL MOTOR CABLE to the desired lens function. C. Repeat steps A and B for additional motors. 2. Connect the desired RED Start/Stop cable. A. Connect the desired RED Start/Stop Cables to the W.M.D. EXP port. B.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CONFIGURE THE 3-AXIS SYSTEM 1. Pair the T.H.C. A. Ensure the RED CAN Command Cable is connected to the W.M.D. and T.H.C. B. Toggle the T.H.C. power switch to Cable mode. Once paired, the T.H.C. retains wireless information for that W.M.D. C. Insert a charged RED Li Battery 7.2V. D. Toggle the T.H.C. power switch to Battery mode. Wait a few seconds for the T.H.C. wireless LED to turn solid blue, signalling a wireless connection. E.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CONFIGURE LENS CONTROL MOTORS The W.M.D. features a number of adjustments in the Focus, Iris, and Zoom menu topics to fine-tune specific motor/lens combinations. After initializing the system, you may need to adjust the following settings: Torque Direction Type/Model Backlash Endstop NOTE: For more information, go to “Configure Focus, Iris, and Zoom Motors” on page 24. METADATA AND LENS PROFILES The microSD slot on the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 03 WIRELESS MOTOR DRIVER (W.M.D.) W.M.D. OVERVIEW The RED ® Wireless Motor Driver (W.M.D.) is the brain of the RED 3-Axis Lens Control System. The W.M.D. receives control signals from the RED Tactical Hand Controller (T.H.C.) to drive up to three (3) RED Lens Control MotorS. With the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. CONTROLS 4 5 1 6 7 2 8 3 W.M.D. Controls # CONTROL DESCRIPTION 1 LCD display View the W.M.D. menus 2 A button Return to home screen; Toggles lock/unlock buttons 3 B button Short press initializes motors that are in an error state; long press initializes all motors 4 Up button Navigate up through the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. LEDS 2 1 W.M.D. LEDs # LED COLOR/FLASHING DESCRIPTION 1 Power Off No power connected Green flashing Firmware upgrading Green Power on; Firmware upgraded Red Power error Amber flashing System boot indicator or initialization in progress 2 Focus, Off Iris, Green flashing Zoom Green Red COPYRIGHT © 2014 RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. CONNECTORS 1 2 5 6 3 7 8 4 W.M.D. Connectors (Side) 10 9 W.M.D. Connectors (Bottom) # CONNECTOR DESCRIPTION COMPATIBLE PARTS PART NUMBERS 1 Wireless antenna Removeable antenna RED T.H.C./W.M.D. Antenna 790-0420 2 Focus connector (7-pin 1B LEMO) Connect the W.M.D. to the Focus Lens Control Motor RED W.M.D. Motor Cable 7-Pin Straight to 7-Pin Right (12”) 790-0434 RED W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E # CONNECTOR DESCRIPTION COMPATIBLE PARTS PART NUMBERS 3 Iris connector (7-pin 1B LEMO) Connect the W.M.D. to the Iris Lens Control Motor RED W.M.D. Motor Cable 7-Pin Straight to 7-Pin Right (12”) 790-0434 RED W.M.D. Motor Cable 7-Pin Straight to 7-Pin Right (18”) 790-0406 RED W.M.D. Motor Cable 7-Pin Straight to 7-Pin Right (24”) 790-0412 RED W.M.D. Motor Cable 7-Pin Straight to 7-Pin Right (12”) 790-0434 RED W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E MOUNT THE W.M.D. The W.M.D. is designed to support various mounting requirements, enabling you to customize your setup for your own camera configuration. ATTACH THE W.M.D. TO THE DSMC TACTICAL RIGHT PLATE When the V-LOCK is removed from the back of the W.M.D., it can be attached to a DSMC ® Tactical Right Plate using the built-in thumbscrew and guide pin. The W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 4. Place the W.M.D. against the Tactical Plate so that the guide pin and 1/4-20 screw each align with a 1/420 screw hole. 5. Push and turn the W.M.D. 1/4-20 thumbscrew until it is hand-tight. DO NOT OVERTIGHTEN. Push and Turn Thumbscrew MOUNT THE W.M.D. TO A V-MOUNT RECEIVER The W.M.D. ships with a V-LOCK to mount the W.M.D. to most industry-standard female v-mount receivers. 1. Align the V-LOCK in the desired position on the back of the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E POWER THE W.M.D. 1. Connect the 2-pin 1B LEMO connector of a RED W.M.D. Power Cable to the PWR port on the W.M.D. 2. Connect the opposite end to a 12 V DC power source with sufficient amperage. NOTE: The W.M.D. is powered on when the power cable is connected to a live power source. Disconnect the power cable to turn off the W.M.D. CONNECT MOTORS 1. Connect a RED W.M.D. Motor Cable to the 7-pin LEMO connector on the motor. 2.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. MAIN MENU The W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CHANGE MOTOR DIRECTION The last direction of the motor persists between reboots. 1. In the W.M.D. main menu, select the desired motor. (Example: Focus, Iris, Zoom) 2. Select Direction. 3. Press Select to toggle to motor direction. (Example: CW, CCW) SELECT MOTOR TYPE/MODEL 1. In the W.M.D. main menu, select the lens function for the specific motor. (Example: Focus, Iris, or Zoom) 2. Select Model. 3. Navigate to the desired motor model. 4.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CONFIGURE WIRELESS SETTINGS In order for the T.H.C. to control the W.M.D., the RED 3-Axis Lens Control System uses a Frequency-Hopping Spread Spectrum (FHSS) wireless link and offers 42 channels. 1. In the W.M.D. main menu, select Wireless. 2. Select a Channel. The range is 1–42. 3. Select a power setting for the strength of the wireless signal. ‒ ‒ Low: The low power setting balances range and low power and is appropriate in most cases.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CONFIGURE START/STOP, GENLOCK, TIMECODE, TALLY This section explains how to set up start/stop, genlock, and timecode with the W.M.D. and a DSMC. For more information about cables and configurations, go to “3-Axis System Cables” on page 63. 1. Configure Start/Stop in the DSMC menu. A. Go to Menu > Settings > Setup > GPIO/Sync > Brain GPIO. B. Select General Purpose In from the Camera In drop-down menu. 2.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 3. Configure Start/Stop in the W.M.D. main menu. A. Select Start/Stop. B. Select a start/stop option based on the intended functionality and cables used.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E SELECT A LENS PROFILE Default lens profiles are located Prime or Zoom menus. Modified lens profiles are saved in the User menu. 1. In the W.M.D. main menu, select Profiles. 2. Select the desired lens profile type. (Example: Prime, Zoom, or User) 3. Select the manufacturer. 4. Select the model. 5. Select the focal length. 6. Press Select to choose the lens profile for the specific lens.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E SAVE A LENS PROFILE If you have made lens profile modifications but did not save changes at the time, follow these steps to save your changes. 1. In the W.M.D. main menu, select Profiles. 2. Select Save.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E MANAGE LENS PROFILES The W.M.D. automatically reads lens information and renames the profile on import. This effectively removes any custom profile names. (Example: A renamed RED PRO PRIME 50mm lens profile is automatically renamed to RED-PRIME-50mm.pfl when imported to the W.M.D.) For this reason, we recommend saving .pfl files in custom named folders, rather than changing the lens profile name. Once you have exported lens profiles from the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 04 TACTICAL HAND CONTROLLER (T.H.C.) T.H.C. OVERVIEW The RED Tactical Hand Controller (T.H.C.) works with the RED Wireless Motor Driver (W.M.D.) and RED Lens Control Motor to provide wireless operation of lens adjustments (Focus, Iris, Zoom). The T.H.C. delivers on-the-fly precision tuning with independent Focus, Iris, and Zoom adjustment controls. Up to two (2) T.H.C. units can be paired with a W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E T.H.C. CONTROLS 1 2 4 3 5 6 7 T.H.C. Controls 8 9 10 T.H.C.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E T.H.C. LEDS 1 2 3 4 T.H.C. LEDs 5 6 7 T.H.C. LEDs # LED COLOR/FLASHING DESCRIPTION 1 Focus Limit Off Function active; no limits set Green flashing (slow) Actively setting limit (User is holding the limit button down) Green flashing (fast) Function locked: no position updates are sent to the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E # LED 4 Battery/Tally 1 Green 5 6 7 Initialize Power Zoom Limit COLOR/FLASHING DESCRIPTION Charged battery Amber Low battery Red Very low battery (replace immediately to avoid power loss) Flashing Tally on; camera is recording Solid Tally off; camera is not recording Off One or motor motors must be initialized; no motors detected Green flashing Initialization in process Green All detected motors are initialized Off Power off
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E T.H.C. CONNECTORS 1 2 T.H.C. Wired Connections 5 3 4 T.H.C. Battery, microSD, and Antenna # CONNECTOR DESCRIPTION COMPATIBLE PARTS PART NUMBERS 1 AUX port Auxiliary power and communication for accessories (RS-232 at 38.4 K) RS232-to-RS232 Cable 790-0150 REDLINK-to-T.H.C.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E WIRED OPERATION 1. Connect the T.H.C. to the W.M.D. using the RED CAN Command Cable (provided). 2. Toggle the power switch to Cable mode. The T.H.C. is now connected and ready for wired operation. T.H.C. Wired Connection PAIR THE T.H.C. Connect and pair the T.H.C. with your W.M.D. to operate in wireless mode. Once paired, the T.H.C. stores wireless information for that W.M.D. and automatically reconnects when in range. The T.H.C.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CHANGE THE WIRELESS CHANNEL 1. Power off the T.H.C. by toggling the power switch to Cable mode. 2. Press and hold the Focus Limit button, and toggle the power switch to Battery mode. 3. After a few seconds, release Focus Limit. Iris Limit and Focus Limit LEDs flash corresponding to the current channel setting: ‒ ‒ Iris Limit: Flashes to represent the tens. ‒ ‒ Focus Limit: Flashes to represent the ones.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E SET A LENS LIMIT The T.H.C. enables precision on-the-fly adjustments for lens functions. 1. Adjust the desired lens function knob/slider (Focus, Iris, or Zoom) to the min/max position. (Example: zoomed out to capture full setting) 2. Press and hold the corresponding Limit button (Focus, Iris, or Zoom) on the T.H.C. Hold Limit Button and Adjust 3. Adjust the corresponding lens function knob/slider (Focus, Iris, or Zoom) to the max/min position.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E SET A LENS LOCK The W.M.D. can support wireless communication with up to two (2) T.H.C. units at any given time. Use the lens function lock feature on the T.H.C. to prevent accidental/unwanted manipulation of that lens function on your T.H.C. unit. 1. Press and hold the Limit button for the desired lens function for three (3) seconds. DO NOT make adjustments to the knob/slider during this time. Hold Limit Button for 3 sec 2.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 05 LENS CONTROL MOTOR Lens Control Motor OVERVIEW The Lens Control Motor delivers precision control and flexibility in a slim, lightweight design. The Lens Control Motor features dual-sided dovetail rails, a tool-free mounting clamp, and a rotating 7-pin LEMO connector for space-saving low profile configuration.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E LENS CONTROL MOTOR MOUNTING BRACKET Mount the Lens Control Motor to 15mm or 19mm support rods using the flexible and tool-free Lens Control Motor Mounting Bracket. The bracket securely attaches to the built-in dove-tail mounting rails on the Lens Control Motor. The bracket is designed for 19mm support rods and is also compatible with 15mm support rods using snap-on reducer bushings.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E LENS DRIVE GEARS RED Lens Drive Gears are magnetic-locking and interchangeable without the use of any tools. Additionally, Lens Drive Gears can be installed on either side of a Lens Control Motor for optimized motor orientation and low profile setup. NOTE: For more information, visit the RED Store at http://www.red.com/store or contact your Bomb Squad representative. RED Lens Drive Gear M 0.8 ATTACH THE LENS CONTROL MOTOR MOUNTING BRACKET 1.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E CONNECT THE Lens Control Motor 1. Connect a RED W.M.D. Motor Cable to the rotating connector on the Lens Control Motor. 2. Connect the opposite end of the RED W.M.D. Motor Cable to the corresponding lens function (Focus, Iris, Zoom) 7-pin LEMO port on the W.M.D. 3. Retract the spring-loaded thumb latch to rotate the connector to the desired position. 4. Release the thumb latch and the rotating connector locks in place.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 06 SYSTEM MAINTENANCE All RED products are designed for rugged durability, but precision instruments demand proper care. Please take note the special care guidelines in this section. WARNING: DO NOT attempt to modify, dismantle or open the Lens Control Motor, Tactical Hand Controller (T.H.C.), Wireless Motor Driver (W.M.D.), or other accessory as doing so may expose you to electric shock and serious injury.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 07 UPGRADE FIRMWARE As part of RED Digital Cinema’s commitment to ongoing product support and development, the Tactical Hand Controller (T.H.C.) and Wireless Motor Driver (W.M.D.) are designed to support firmware upgrades for improved functionality and additional features in the future. The T.H.C. and W.M.D. are updated independently of each other. You can load both the T.H.C. and W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E play and the Power LED flashes green. When the upgrade is complete, the LCD display shows “Done” and the Power LED turns solid green. 9. Power off the W.M.D. 10. Remove the microSD card. VERIFY CURRENT T.H.C. FIRMWARE There is currently no way to verify current firmware version. If you are experiencing problems, upgrade to the latest firmware version available at www.red.com/downloads. UPGRADE T.H.C.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 08 TROUBLESHOOT THE SYSTEM GENERAL TOPICS POWER FAILURE SYMPTOM The W.M.D. shuts off randomly during operation. EXPLANATION The 12 V auxiliary (AUX) port(s) on many DSMC ® power modules, including the REDVOLT ® XL MODULE, provide a maximum of 3.8 A of current and is sufficient for most operating conditions. In certain instances, when driving multiple motors simultaneously on a stiffer than normal lens, the W.M.D. may draw more than 3.8 A.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E TROUBLESHOOT THE W.M.D. W.M.D. DOES NOT RECOGNIZE MOTOR SYMPTOM The W.M.D. does not recognize a motor. POTENTIAL RESOLUTIONS Ensure that the W.M.D. is connected to the motor. Ensure that the problem is not related to a faulty or damaged cable. Try connecting the W.M.D. and motor with another cable. Ensure that you are using a supported motor (for a list of supported motors, go to “3-Axis System Compatibility” on page 54.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E LENS FUNCTION DOES NOT RESPOND SYMPTOM A lens function (Focus, Iris, Zoom) is not responding. POTENTIAL RESOLUTIONS The lens function may be locked. To resolve this issue, use the steps described in “Remove a Lens Lock” on page 40. Ensure the motor’s torque setting is set appropriately. The torque value may be too low. Ensure you are using the appropriate motor cable. If you are experiencing issues with the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E TROUBLESHOOT FIRMWARE UPGRADE SYMPTOM The W.M.D. or T.H.C. does not recognize the firmware upgrade file or is not upgrading properly. POTENTIAL RESOLUTIONS Start with a freshly formatted microSD card. Ensure that there is no other data on the microSD card besides the upgrade file. Use the microSD card provided by RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E A TECHNICAL SPECIFICATIONS Tactical Hand Controller (T.H.C.) Dimensions Height Height Width: Depth: (with antenna): 9.00 in. (228.6 mm) (without antenna): 8.08 in. (205.2 mm) 3.50 in. (88.9 mm) 4.32 in. (109.7 mm) Weight 32.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E Lens Control Motor Maximum Peak Torque 0.85 Nm Maximum Speed 4.5 rev/second Dimensions Height: 1.75 in. (44.5 mm) Width: 1.00 in. (25.4 mm) Depth: 4.50 in. (11.4 mm) Weight 5.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E B 3-AXIS SYSTEM COMPATIBILITY COMPATIBLE MOTORS The following motors are currently supported by the RED ® Wireless Motor Driver (W.M.D.) and RED Tactical Hand Controller (T.H.C.): RED Lens Control Motor (DLM1) Element DLM1 (coming soon) Heden M21VE Heden M26VE Preston DM1 Preston DM1x Preston DM2 COMPATIBLE MOTOR DRIVERS RED Lens Control Motors are compatible with the following motor drivers, which require a 3.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E C CONNECTOR AND CABLE PINOUTS This appendix provides RED 3-Axis Lens Control System pinout information for the Wireless Motor Driver, Tactical Hand Controller, Lens Control Motor as well as RED ® connector cables that are used with the system components. NOTE: When connecting a cable to a connector, align the key and red marker on the cable connector with the corresponding key and marker on the device connection.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. LENS MOTOR CONNECTOR The W.M.D. Lens Motor connector is an industry-standard 7-pin 1B LEMO connector. 1 2 6 7 5 3 4 W.M.D. 7-Pin 1B lens drive connector 7-PIN 1B LEMO LENS DRIVE CONNECTOR PIN SIGNAL 1 Motor (+) 2 Motor (-) 3 Encoder A 4 +5 V 5 GND 6 Encoder B 7 Motor ID W.M.D. CAN CONNECTOR The W.M.D. CAN connector is a 4-pin 0B LEMO connector that provides power and CAN communications between the W.M.D. and T.H.C.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. START/STOP/TALLY EXPANSION CONNECTOR The W.M.D. Start/Stop/Tally expansion connector is a 14-pin 1B connector that provides expansion (EXP) support for the RED 3-Axis Lens Control System. 1 2 10 11 12 14 13 3 4 5 6 9 8 7 W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. AUX CONNECTOR The W.M.D. AUX connector is a 10-pin 1B connector used for RS-232 communication and power with other third-party systems and accessories. 1 5 8 2 9 7 3 10 6 4 5 W.M.D. 10-pin 0B RS232 connector 6-PIN 0B LEMO AUX CONNECTOR PIN SIGNAL 1 Pwr Out 2 232 Tx 3 232 Rx 4 422 Tx+ 5 422 Rx+ 6 422 Rx- 7 422 Tx- 8 232 Jumper 9 232 Jumper 10 GND COPYRIGHT © 2014 RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. POWER CONNECTOR The W.M.D. PWR connector is a 2-pin 1B LEMO power connector to supply power to the W.M.D. from your camera or other power modules. 1 2 W.M.D. 2-Pin 1B Power connector 2-PIN 1B LEMO POWER CONNECTOR PIN SIGNAL 1 GND 2 +12 V COPYRIGHT © 2014 RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E T.H.C. CONNECTORS 1 2 T.H.C. Connections # CONNECTOR CONNECTOR TYPE CONNECTOR FUNCTION 1 AUX 6-pin 0B LEMO RS-232 communication to auxiliary devices 2 CAN 4-pin 1B LEMO CAN communication and power from the W.M.D. T.H.C. AUX CONNECTOR The T.H.C. AUX connector is a 6-pin 0B LEMO connector on the T.H.C. used for RS-232 communications and power with third-party systems and accessories. NOTE: The T.H.C.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E T.H.C. CAN CONNECTOR The T.H.C. CAN connector is a 4-pin 0B LEMO connector that provides power and CAN communications between the W.M.D. and T.H.C., or other auxiliary devices. 1 4 2 3 T.H.C. 4-Pin 0B CAN Connector 4-PIN 0B LEMO CAN CONNECTOR PIN SIGNAL 1 GND 2 CANL 3 CANH 4 VCC COPYRIGHT © 2014 RED.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E Lens Control Motor CONNECTORS 1 # CONNECTOR TYPE CONNECTOR FUNCTION 1 7-pin 1B LEMO Lens motor drive support Lens Control Motor Connection Lens Control Motor CONNECTOR The Lens Control Motor connector is an industry-standard 7-pin 1B LEMO connector.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E 3-AXIS SYSTEM CABLES RED W.M.D. MOTOR CABLE (FOCUS, IRIS, ZOOM) The RED W.M.D. Motor Cable is a 7-pin 1B to 7-pin 1B LEMO cable used to connect RED Lens Control Motors to the W.M.D. Cables are available in 12", 18", and 24". NOTE: The RED Lens Control Motor is also compatible with third-party systems using an appropriate RED motor cable with the proper internal identification resistor. For more information, visit the RED Store at http://www. red.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E RED LENS CONTROL MOTOR CABLE (3.3KΩ VERSION) The RED Lens Control Motor Cable (3.3KΩ Version) provides a 7-pin 1B to 7-pin 1B LEMO cable used to connect RED Lens Control Motors to compatible third-party motor drivers. This cable provides a 3.3k ohms (Ω) resistance identification to the motor driver. Cables are available in 18" and 24".
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E RED CAN COMMAND CABLE (5', 50', 100') The RED CAN Command Cable is a 4-pin 0B to 4-pin 0B LEMO cable that provides CAN communications and power from the W.M.D. to the T.H.C. It is used for wired operation and wireless pairing of T.H.C. units. RED CAN Command Cable (5') W.M.D. CAN T.H.C. CAN FGG-0B.304.CLAD52Z FGG-0B.304.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E W.M.D. POWER CABLE 2-PIN 1B TO 2-PIN 0B The W.M.D. Power Cable 2-Pin 1B to 2-Pin 0B (18") connects your RED W.M.D. to a standard 12 V 2-pin 0B LEMO accessory port (found on the QUICKPLATE MODULE and REDVOLT XL MODULE) to power the RED 3-Axis Lens Control System. W.M.D. Power Cable 2-Pin 1B to 2-Pin 0B (18") W.M.D. POWER DSMC POWER MODULE FGG-1B.302.CLAD62Z FGG-0B.302.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E RED START/STOP CABLE (1B TO SYNC, CTRL, BNC) The RED Start/Stop Cable (1B to Sync, Ctrl, BNC) provides Start/Stop, Tally, Genlock and Timecode support. This cable connects to the EXP port on the W.M.D. and the CTRL port of your DSMC, with an additional BNC for jamming Timecode. NOTE: Full support requires the 3BNC-to-00 LEMO Sync Cable and a BNC-TO–BNC Adaptor (included with the RED 3-Axis Lens Control System).
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E RED START/STOP CABLE (1B TO BNC) The RED Start/Stop Cable (1B to BNC) provides Start/Stop, Genlock, and Timecode support. This cable connects to the EXP port on the W.M.D. and an auxiliary device for Start/Stop, Genlock and Timecode. NOTE: Full support requires the 3BNC-to-00 LEMO Sync Cable and a BNC-TO–BNC Adaptor (included with the RED 3-Axis Lens Control System). RED Start/Stop Cable (1B to BNC) W.M.D. EXPANSION PORT EPIC START/STOP FGG-1B.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E RED START/STOP CABLE (1B TO 00B SYNC) The RED Start/Stop Cable (1B to 00B Sync) supports Start/Stop functionality through the RED W.M.D. This cable connects to the EXP port on the W.M.D. and to the SYNC port of your DSMC and is ideal for run-and-gun shooters who want convenient Start/Stop capability only. NOTE: When using the RED Start/Stop Cable (1B to 00B Sync), you must configure the W.M.D. for EPIC start/ stop operation only. On the W.M.D.
R E D 3 - A X I S S Y S T E M O P E R AT I O N G U I D E D W.M.D. MAIN MENU MAP W.M.D.
RED DIGITAL CINEMA COPYRIGHT© 2014 RED.COM, INC. All trademarks, trade names, logos, icons, images, written material, code and product names used in association with the accompanying product are the copyrights, trademarks or other intellectual property owned and controlled exclusively by RED.COM, INC.
