User Manual
Table Of Contents
- Table of contents
- Introduction
- Mounting the 1000AP
- Figure 1: Mounting the 1000AP to a ceiling or wall
- To mount on a ceiling or wall:
- 1. Select a location on a ceiling or wall to mount the 1000AP (we recommend mounting on a ceiling).
- 2. Ensure the ceiling or wall can support the 1000AP’s weight (around 250 g or 8.5 oz). If in dou...
- 3. Install the Category 5 Ethernet cable according to whether you decided to ‘star-wire’ or ‘dais...
- 4. Use the mounting bracket as a template to mark out drill positions.
- 5. Drill two holes (43 mm apart) using a 5.5 mm drill bit. Ensure the two holes are vertically al...
- 6. Insert suitable fastenings into the holes (e.g. wall plugs).
- 7. Position the mounting bracket over the two holes and insert the appropriate screws.
- 8. Connect the cables from the hole in the ceiling/wall to the 1000AP.
- 9. Slide the 1000AP over the mounting bracket until it fits into the groove. Continue sliding unt...
- Connecting the cables
- Star-wiring from a 3000AS
- Star-wiring from a Linux server
- Daisy-chaining
- Figure 3: Daisy-chain installation
- 1. Connect a Category 5 Ethernet cable (with RJ-45 connectors) to the 1000AP’s IN port.
- 2. Connect the other end of the cable to the 3000AS’s blue Access Point port or purple Office LAN...
- 3. Connect the first 1000AP’s OUT port to the second 1000AP’s IN port. Ensure there is no more th...
- Using more complicated networks
- Connecting power
- 1. Connect the loose power cable to the country- specific mains power lead.
- 2. Connect the mains power lead to an electricity supply.
- 3. Insert the other end of the cable into the 1000AP’s DC 12v power port. The 1000AP’s LED indica...
- 4. The 1000AP is now ready to use. You can configure the 1000AP’s software features through the G...
- Configuring 1000APs
- To edit the 1000AP’s configuration
- 1. Log on to the management interface as an administrator from a management PC.
- 2. The AP List dialog displays with all connected access points. If a 1000AP is missing from this...
- 3. Click on a 1000AP’s name or hardware address to open the AP Stats dialog, which shows informat...
- 4. Click on AP Record to open the Bluetooth AP Edit dialog. In this dialog, you can rename the 10...
- To edit the 1000AP’s configuration
- Using Identify mode
- Reading the LED
- LED startup sequence
- 1. When power is connected, the LED is orange for about a second to indicate that power is on.
- 2. The LED flashes orange for a few seconds to indicate that the 1000AP is starting up and conduc...
- 3. The LED illuminates steady red after startup to indicate normal operation.
- 4. If the 1000AP has passed its startup tests but cannot either connect to Genos or obtain an IP ...
- 5. If there is a fatal error at any time, the LED illuminates steady orange. If it remains in thi...
- LED indicator status chart
- LED startup sequence
- 1000AP diagram
- Contact information
- Regulatory information
- The following regulatory statements apply to the Red-M 1000AP access point.
- By attaching themark to this product, we confirm:
- To conform with FCC rules regarding RF exposure, this equipment should be installed a minimum of ...
- Any changes or modifications not expressly approved by the manufacturer could void the user’s aut...
- This device has been designed to operate with an antenna that has a maximum gain of 0 dB. Antenna...
- To reduce potential radio interference to other users, the antenna type and its gain should be so...
- To prevent radio interference to the licensed service in Canada, this device is intended to be op...
- This product is designed to connect to "Bluetooth" compatible radio interfaces using the 2.4 GHz ...
- [Member States of the EEA are: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Icela...
- English
- Dansk
- Deutsch
- Español
- Flemish
- Français
- Íslenska
- Italiano
- Nederlands
- Norsk
- Português
- Suomi
- Svensk
Red-M 1000AP getting started guide
20
Italiano
ATTENZIONE: Utilizzare questo prodotto solo con sorgenti di
alimentazione che soddisfano i requisiti di sicurezza IEC 60950 o
equivalenti. Utilizzare l'alimentatore fornito (ove applicabile) o
contattare Red-M per ottenere un elenco delle sorgenti di alimentazione
adeguate.
Nederlands
WAARSCHUWING: Gebruik dit product alleen met een voedingsbron die
voldoet aan de "Minimum voedingsbron"-vereisten van IEC 60950 of
evenwaardige veiligheidsvoorschriften. Gebruik de bijbehorende
voedingsbron (indien van toepassing) of neem contact op met Red-M
voor een lijst van geschikte voedingsbronnen.
Norsk
FORSIKTIG: Dette produktet skal bare brukes med en strømkilde som
tilfredsstiller kravene til "Begrenset strømkilde" i IEC 60950 eller
tilsvarende sikkerhetsstandard. Bruk den medfølgende
strømforsyningen (hvis en slik finnes) eller kontakt Red-M for å få en
oversikt over passende strømkilder.
Português
Advertência: Utilize este produto apenas com uma fonte de energia que
respeite os requisitos definidos em "Fontes de Energia Limitadas" da
norma IEC 60950 ou dos padrões de segurança equivalentes. Utilize a
fonte de alimentação fornecida (se aplicável) ou contacte Red-M para
obter uma lista de fontes adequadas.
Suomi
MUISTUTUS: Käytä tätä tuotetta vain sellaisen virtalähteen yhteydessä,
joka täyttää standardin 60950 "rajoitetun virtalähteen" tai muiden
vastaavien standardien asettamat turvallisuusvaatimukset. Käytä
toimitettua virtalähdettä (jos asianmukaista) tai ota yhteys RedM:ään
sopivien virtalähteiden luettelon saamiseksi.
Svensk
FÖRSIKTIGT! Denna produkt får bara användas med en effektkälla som
uppfyller kraven för "Begränsad effektkälla" i IEC 60950 eller
motsvarande säkerhetsnormer. Använd medföljande effektkälla (i
förekommande fall) eller begär en lista över lämpliga effektkällor från
Red-M.
Σλληνικά
ΠΡΟΣΟΧΗ
:
Χ
ρησιµοποι
ή
στε αυτ
ό
το προ
ϊό
ν µ
ό
νο µε πηγ
ή
εν
έ
ργειας που ε
ί
ναι σ
ύ
µφω
νη µε την οδηγία του IΕC 60950 περί «Περιορισµένης Πηγής Ενέργειας» ή αντίστοιχων
προδιαγ ραφών ασφαλείας. Χρησιµοποιήστε την πηγή ενέργειας που παρέχεται
(αν είναι κατάλληλη) ή επικοινωνήστε µε την Red-M για να σας προµηθεύσει µε
κατάλογο συµβατών πηγών ενέργειας