Signal Conversion Isolation Power Supplies Communication Modules DIN-Rail Relays
ITMS IRMA ITMA APMR VFC/ CFC IAMS AAMA IAMA Models 191 187 183 181 179 173 169 167 Page Signal Conditioner Signal Conditioner Signal Conditioner 3 Phase Fault Detector Signal Conditioner Signal Conditioner Signal Conditioner Signal Conditioner Functions RTD Thermocouple RTD Thermocouple 230 V 380 V 480 V AC DC Current DC Volts DC Current DC Volts DC Current DC Volts DC Current DC Volts Input ALARMS DC Current DC Volts DC Current DC Volts ALARMS FREQ ALARMS D
PSDR12 PSDR13 PSDR6 PRS1 IFMR PRA1 IFMA Models 208 209 207 197 195 199 193 Page Power Supply Power Supply Power Supply Speed Switch Speed Switch Signal Conditioner Signal Conditioner Functions 120 VAC 220 VAC 120 VAC 184 to 264 VAC 86 to 132 VAC FREQ FREQ FREQ FREQ Input 24 VDC @ 100 mA 24 VDC @ 1 Amp 24 VDC @ 650 mA ALARMS ALARMS DC Current DC Volts DC Current DC Volts Outputs DIN Rail DIN Rail DIN Rail 12 Pin Socket DIN Rail 12 Pin Socket DIN Rail Package
AVMR RSRLYB RLY7 RLY6 Models 218 211 216 214 Page Relay Relay (Replaceable) 3 Phase Solid State Relay Solid State Relay Functions 24 VDC 24 VDC 4 to 28 VDC 4 to 28 VDC Input Form A 3 Amp SPST Contacts Form C 6 Amp SPDT Contacts 30 A 3 Phase @ 660 VAC Maximum 25 A @660 VAC Maximum Outputs DIN Rail DIN Rail DIN Rail DIN Rail Package Power Agency Software Signal Conditioning & Communications Quick Reference
GWDN GCM422 GCM232 ICM4 Models 205 204 203 201 Page RS422/RS485 DeviceNet Gateway RS422/485 to 20 mA Current Loop Converter RS232 to 20 mA Current Loop Converter RS232 to RS285 Converter Functions Input Outputs DIN Rail In-line Module Via Bus DC DC DC DIN Rail In-line Module Power Package Agency Software Quick Reference Signal Conditioning & Communications
Signal Conditioning & Communications Notes Red Lion
Signal Conditioning & Communications DC Inputs MODEL IAMA - UNIVERSAL SIGNAL CONDITIONING MODULE O 3-WAY ISOLATION OF ANALOG SIGNALS O UNIVERSAL CONVERSION MODULE - INPUTS AND OUTPUTS CAN BE SELECTED VIA DIP SWITCH SETTINGS O OVER 100 INPUT AND OUTPUT ANALOG CONVERSION COMBINATIONS O ALL RANGES ARE FACTORY PRECALIBRATED.
Signal Conditioning & Communications DC Inputs MODEL IAMA - UNIVERSAL SIGNAL CONDITIONING MODULE Input Specifications TABLE 1, OUTPUT RANGE SETTINGS 1. INPUT/OUTPUT RANGES: See Tables 1 and 2 2. ZERO/SPAN ADJUSTMENTS: Digital (DIP Switch Transition) 3. MAX INPUT SIGNAL: Current Input: 110 mA DC, 1.1 VDC Voltage Inputs: Terminal 7- 1 V +10% Terminal 8- 10 V +10% Terminal 9- 100 V +10% 4. INPUT RESISTANCE: Current: 10 : Voltage: > 100 K 5. INPUT PROTECTION: Surge suppressor diodes 6.
Signal Conditioning & Communications DC Inputs MODEL AAMA - UNIVERSAL SIGNAL CONDITIONING MODULE O 3-WAY ISOLATION OF ANALOG SIGNALS O UNIVERSAL CONVERSION MODULE - INPUTS AND OUTPUTS CAN BE SELECTED VIA DIP SWITCH SETTINGS O OVER 100 INPUT AND OUTPUT ANALOG CONVERSION COMBINATIONS O 18 to 30 VDC MODULE POWER EMC COMPLIANT Product Features Click Icon For User Bulletin FAX/WEB DOC# 10019 The AAMA3535 Universal Signal Conditioning Module can isolate and convert over 100 combinations of industry
Signal Conditioning & Communications DC Inputs MODEL AAMA - UNIVERSAL SIGNAL CONDITIONING MODULE Input Specifications 1. INPUT RANGES: 0 to 60 mV 0 to 100 mV 0 to 200 mV 0 to 300 mV 0 to 500 mV 0 to 1 V 0 to 5 V 0 to 10 V 0 to 20 V ±100 mV ±200 mV ±300 mV ±500 mV ±1 V ±2 V ±5 V ±10 V ±20 V 0 to 5 mA 0 to 20 mA 4 to 20 mA 1 to 5 V 0 to 2 V ±60 mV 2. ZERO/SPAN ADJUSTMENTS: Range Dependent 3. MAX. INPUT SIGNAL: Current Input: 50 mA Voltage Input: 30 V 4.
Signal Conditioning & Communications DC Inputs MODEL AIMI - 0 (4) - 20 MA PASSIVE LOOP POWERED ISOLATOR UL RECOGNIZED USA O PROVIDES INPUT/OUTPUT ISOLATION O LOOP POWERED EMC COMPLIANT Product Features Click Icon For User Bulletin FAX/WEB DOC# 10015 Compact passive loop powered isolator provides ground potential isolation of analog control circuits, 0 to 20 mA and 4 to 20 mA. The isolator ensures safe decoupling of the sensor signal from the control electronics.
Signal Conditioning & Communications DC Inputs MODEL AIMI - 0 (4) - 20 MA PASSIVE LOOP POWERED ISOLATOR Output Specifications 1. OUTPUT SIGNAL: 0 to 20 mA Load Resistance: d 1000 : Ordering Information MODEL NO.
Signal Conditioning & Communications DC Inputs MODEL IAMS - SMART ANALOG TO MODBUS CONDITIONER W/ALARMS EMC COMPLIANT O ANALOG TO MODBUS CONVERSION O 18 DIFFERENT DC ANALOG INPUT RANGES O PROCESSOR BASED SCALING O PC CONFIGURATION SOFTWARE O DUAL SETPOINT RELAY ALARMS O FOUR WAY SIGNAL ISOLATION PROGRAMMING SOFTWARE Product Features Click Icon For User Bulletin FAX/WEB DOC # 10016 The IAMS3535 Smart Analog to MODBUS Conditioner with Alarms module accepts a wide range of DC analog process
Signal Conditioning & Communications DC Inputs MODEL IAMS - SMART ANALOG TO MODBUS CONDITIONER W/ALARMS General Specifications Continued 5. CERTIFICATIONS AND COMPLIANCE: SAFETY EN 61010-1, IEC 1010-1 ELECTROMAGNETIC COMPATIBILITY Immunity to EN 50082-2 Emissions to EN 50081-2 6. CONSTRUCTION: Case body is green high impact plastic. Installation Category II, Pollution Degree 2. 7. CONNECTIONS: 14 AWG max. 8.
Signal Conditioning & Communications DC Inputs MODEL AIMR - LOOP POWERED SETPOINT ALARM EMC COMPLIANT O LOOP POWERED - NO EXTERNAL 24 VDC POWER SUPPLY REQUIRED O LOW BURDEN ON THE 4 TO 20 mA LOOP (275:) O BI-STABLE RELAY - REQUIRES NO HOLDING CURRENT O CONFIGURABLE RELAY ACTION - LATCHING OR NON-LATCHING O SPDT RELAY CONTACT RATED 1 A, 125 VAC O REPEATABILITY BETTER THAN 0.
Signal Conditioning & Communications DC Inputs MODEL AIMR - LOOP POWERED SETPOINT ALARM Input Specifications 1. 2. 3. 4. 5. 6. INPUT SIGNAL: 4 to 20 mA VOLTAGE DROP: 5.5 V LOOP BURDEN: 275 : SETPOINT RANGE: 4 to 20 mA HYSTERESIS RANGE: 0.1 mA, 1.0 mA TEMPERATURE COEFFICIENT: <0.01%/K Output Specifications 1. OUTPUT TYPE: Form C contacts max. rating 1 A @ 125 VAC, 150 VDC Max. Switching Capacity: 30 W DC 60 VA AC Mechanical Life: 108 switching cycles Ordering Information MODEL NO.
Signal Conditioning & Communications DC Inputs MODEL AAMR - DUAL SETPOINT ANALOG ALARM MODULE UL RECOGNIZED USA EMC COMPLIANT O SELECTABLE ANALOG INPUTS ( 0 to 10 VDC or 0 to 20 mA) O 0 to 100% FULL SCALE RELAY TRIP POINT ADJUSTMENTS O 20 to 30 VDC MODULE POWER ±2% ZERO/SPAN O FORM C RELAY OUTPUTS RATED 3 A, 250 VAC/DC O REPEATABILITY BETTER THAN 0.1% FULL SCALE O ACCURACY GREATER THAN 0.
Signal Conditioning & Communications DC Inputs MODEL AAMR - DUAL SETPOINT ANALOG ALARM MODULE Output Specifications 1. OUTPUT TYPE: 2 Form C contacts max. rating 3 A @ 250 VAC/DC Contacts: Silver Cadmium Oxide (Ag CdO) Relay Output Time Delay: 0 to 4 seconds Ordering Information MODEL NO.
Signal Conditioning & Communications DC Inputs MODEL VFC - VOLTAGE TO FREQUENCY CONVERTER MODEL CFC - CURRENT TO FREQUENCY CONVERTER O 0 to 10 VDC OR 4 to 20 mA INPUT UNITS O AC OR DC OPERATION O ADJUSTABLE ZERO & SPAN FOR FREQUENCY FINE TUNE O ADJUSTABLE LOW END CUT-OUT (Output Inhibit) O 3 NPN OPEN COLLECTOR OUTPUTS (10 KHz, 1 KHz, 100 Hz) O LINEARITY 1% OF FULL SCALE Product Features Click Icon For User Bulletin FAX/WEB DOC # 12015 The Voltage/Current to Frequency Converter is a plug-in
Signal Conditioning & Communications DC Inputs MODEL VFC - VOLTAGE TO FREQUENCY CONVERTER MODEL CFC - CURRENT TO FREQUENCY CONVERTER Input Specifications 1. INPUT: Model VFC: 0 to 10 VDC, Impedance greater than 600 K:. Model CFC: 4 to 20 mA, 30 : Impedance, burden less than 600 mV @ 20 mA Protection: 100% of full scale input Common Mode Rejection: 120 dB, 0-60 Hz Normal Mode Rejection: 35 dB @ 50/60 Hz 2. ACCURACY: Linearity: within 1% of full scale Zero Drift: 0.06% per °C of full scale Span Drift: 0.
Signal Conditioning & Communications AC Inputs MODEL APMR - 3 PHASE FAULT DETECTION DIN RAIL MODULE EMC COMPLIANT O PROTECTS AGAINST PHASE LOSS, UNBALANCE, UNDER VOLTAGE, AND PHASE REVERSAL O AVAILABLE IN 230, 380, OR 480 VAC O LOW COST O DIN RAIL MOUNTABLE O INRUSH UNDER VOLTAGE DELAY ALARMS Product Features Click Icon For User Bulletin FAX/WEB DOC# 10003 The APMR protects three phase equipment, mostly motors, from destructive line conditions.
Signal Conditioning & Communications AC Inputs MODEL APMR - 3 PHASE FAULT DETECTION DIN RAIL MODULE Input Specifications 1. POWER: 230 VAC: Min = 185, Max = 264, 3 VA (Typical)Nominal is 185 to 240, 48 to 62 Hz. 380 VAC: Min = 320, Max = 457, 3 VA (Typical)Nominal is 320 to 415, 48 to 62 Hz. 480 VAC: Min = 380, Max = 528, 3 VA (Typical)Nominal is 380 to 480, 48 to 62 Hz. 2. TEMPERATURE COEFFICIENTS: Unbalance: ±0.5% Over temperature range Undervoltage: ±200 PPM/°C Output Specifications 1.
Signal Conditioning & Communications Temperature MODEL ITMA - INTELLIGENT THERMOCOUPLE MODULE WITH ANALOG OUTPUT O USER PROGRAMMABLE INPUT (Thermocouple types J, K, T, & E, or millivolt) O 12 to 42 VDC LOOP POWERED (4 to 20 mA Output) O MICROPROCESSOR CONTROLLED O SIMPLE ADJUSTABLE RANGE SETTING (Using Input Signal) O THERMOCOUPLE BREAK DETECTION O MOUNTS ON “T” AND “G” STYLE DIN RAILS O 2-WAY ELECTRICAL ISOLATION (INPUT/OUTPUT & POWER) O HIGH-DENSITY PACKAGING (22.
Signal Conditioning & Communications Temperature MODEL ITMA - INTELLIGENT THERMOCOUPLE MODULE WITH ANALOG OUTPUT Input Specifications 1. INPUT: J, K, T, E, mV [selectable via DIP switch] 2. RANGE & ACCURACY: (12 Bit resolution) Accuracy: ± ( 0.075% Range + 0.25°C [Conformity] + 0.50°C [Ice Point]) at 23°C after 20 min. warm-up, conforming to ITS-90. Note: TC Conformity and Ice Point do not apply to mV input Relative Humidity: Less than 85% RH (non-condensing) Span: The input span can be set to a min.
Signal Conditioning & Communications Temperature MODEL ITMA DC - INTELLIGENT THERMOCOUPLE MODULE WITH ANALOG OUTPUT O USER PROGRAMMABLE INPUT (Thermocouple types J, K, T, & E, or Millivolt) O MICROPROCESSOR CONTROLLED O SIMPLE ADJUSTABLE RANGE SETTING (Using Input Signal) O THERMOCOUPLE BREAK DETECTION O MOUNTS ON “T” AND “G” STYLE DIN RAILS O 3-WAY ELECTRICAL ISOLATION (POWER/INPUT/OUTPUT) O MULTIPLE ANALOG OUTPUTS (0 to 20 mA, 4 to 20 mA, and 0 to 10 VDC) O WIDE OPERATING TEMPERATURE RANG
Signal Conditioning & Communications Temperature MODEL ITMA DC - INTELLIGENT THERMOCOUPLE MODULE WITH ANALOG OUTPUT Input Specifications 1. INPUT: J, K, T, E, mV [selectable via DIP switch] 2. TC BREAK DETECTION: Nominal values shown in the following order: (0 to 20 mA, 4 to 20 mA, and 0 to 10 VDC). Upscale: 22.9 mA, 22.5 mA, and 11.5 VDC Downscale: -0.5 mA, 3.5 mA, and -0.4 VDC 3. TEMPERATURE EFFECTS: Temperature Coefficient: ± 0.025% of input range per °C Ice Point Compensation: ± 0.
Signal Conditioning & Communications Temperature MODEL IRMA - INTELLIGENT RTD MODULE WITH ANALOG OUTPUT O USER PROGRAMMABLE INPUT (RTD alpha=0.00385 (DIN 43760), alpha=0.00392, or resistance) O 12 to 42 VDC LOOP POWERED (4 to 20 mA Output) O MICROPROCESSOR CONTROLLED O SIMPLE ADJUSTABLE RANGE SETTING (Using Input Signal) O RTD BREAK DETECTION O MOUNTS ON “T” AND “G” STYLE DIN RAILS O 2-WAY ELECTRICAL ISOLATION (INPUT/OUTPUT & POWER) O HIGH-DENSITY PACKAGING (22.
Signal Conditioning & Communications Temperature MODEL IRMA - INTELLIGENT RTD MODULE WITH ANALOG OUTPUT Input Specifications 1. INPUT: RTD 2, 3, or 4 wire, 100 ohm platinum, alpha = 0.00385 (DIN 43760), alpha = 0.00392, or resistance [selectable via DIP switch] Excitation: 0.170 mA nominal Lead resistance: Less than 0.5°C with 15 ohms max. per lead Note: There is no lead compensation for 2 wire input. Field calibration should be accomplished with equivalent series resistance. 2.
Signal Conditioning & Communications Temperature MODEL IRMA DC - INTELLIGENT RTD MODULE WITH ANALOG OUTPUT y O USER PROGRAMMABLE INPUT (RTD alpha = 0.00385 (DIN 43760), alpha = 0.
Signal Conditioning & Communications Temperature MODEL IRMA DC - INTELLIGENT RTD MODULE WITH ANALOG OUTPUT Input Specifications 1. INPUT: RTD 2, 3, or 4 wire, 100 ohm platinum, alpha = 0.00385 (DIN 43760), alpha = 0.00392, or resistance [selectable via DIP switches]. Excitation: 0.170 mA nominal Lead resistance: Less than 0.5°C with 15 ohms max. per lead Note: There is no lead compensation for 2 wire input. Field calibration should be performed with equivalent series resistance. 2.
Signal Conditioning & Communications Temperature MODEL ITMS - INTELLIGENT TEMPERATURE TO MODBUS CONDITIONER W/ALARMS EMC COMPLIANT Click Icon For User Bulletin PROGRAMMING SOFTWARE ALARMS O TEMPERATURE TO MODBUS CONVERSION O ACCEPTS THERMOCOUPLE, RTD, mV OR RESISTANCE SIGNALS O PROCESSOR BASED SCALING O FOUR WAY SIGNAL ISOLATION O RELAY ALARMS BUILT-IN FOR LOCAL ACTION CAPABILITY COMMUNICATIONS CAPABILITY Product Features FAX/WEB DOC # 10017 The ITMS4037 Intelligent Temperature to MODBUS
Signal Conditioning & Communications Temperature MODEL ITMS - INTELLIGENT TEMPERATURE TO MODBUS CONDITIONER W/ALARMS General Specifications Continued 5. CERTIFICATIONS AND COMPLIANCE: SAFETY EN 61010-1, IEC 1010-1 ELECTROMAGNETIC COMPATIBILITY Immunity to EN 50082-2 Emissions to EN 50081-2 6. CONSTRUCTION: Case body is green high impact plastic. Installation Category II, Pollution Degree 2. 7. CONNECTIONS: Wire clamping screw terminals. 8.
Signal Conditioning & Communications Frequency MODEL IFMA - DIN-RAIL FREQUENCY TO ANALOG CONVERTER O SIMPLE ON-LINE RANGE SETTING (Using Actual Input Signal or Signal Generator) O USER SETTABLE FULL SCALE FREQUENCY FROM 1 Hz to 25 KHz O FOUR OUTPUT OPERATING RANGES (0 to 5 V, 0 to 10 V, 0 to 20 mA, and 4 to 20 mA) O PROGRAMMABLE INPUT CIRCUIT ACCEPTS OUTPUTS FROM A VARIETY OF SENSORS O 85 to 250 VAC and 9 to 32 VDC POWERED VERSIONS AVAILABLE O LOW FREQUENCY CUT-OUT AND OVERRANGE INDICATION O
Signal Conditioning & Communications Frequency MODEL IFMA - DIN-RAIL FREQUENCY TO ANALOG CONVERTER Input Specifications 1. OPERATING FREQUENCY RANGE: From 0 Hz to 25 KHz; user selectable. 2. SIGNAL INPUT: DIP switch selectable to accept signals from a variety of sources, including switch contacts, outputs from CMOS or TTL circuits, magnetic pickups, and all standard RLC sensors. Current Sourcing: Internal 1 K: pull-down resistor for sensors with current sourcing output. (Max.
Signal Conditioning & Communications Frequency MODEL IFMR - DIN-RAIL SPEED SWITCH UL RECOGNIZED USA UL RECOGNIZED CANADA O SIMPLE ON-LINE TRIP FREQUENCY SETTING (USING ACTUAL INPUT SIGNAL OR FREQUENCY GENERATOR) O USER SETTABLE TRIP FREQUENCY FROM 0.
Signal Conditioning & Communications Frequency MODEL IFMR - DIN-RAIL SPEED SWITCH Input Specifications 1. OPERATING FREQUENCY RANGE: 0 Hz to 25 KHz 2. SIGNAL INPUT: DIP switch selectable to accept signals from a variety of sources, including switch contacts, outputs from CMOS or TTL circuits, magnetic pickups, and all standard RLC sensors. Current Sourcing: Internal 1 K: pull-down resistor for sensors with current sourcing output. (Max. sensor output current = 12 mA @ 12 V output.
Signal Conditioning & Communications Frequency MODEL PRS1 - PLUG-IN SPEED SWITCH O 5 RANGES, FROM .1Hz to 10 KHz O OVER-SPEED, UNDER-SPEED, OR ZERO-SPEED DETECTION O 4 OPERATING MODES O REPEATABILITY TO 1/2% OF MAX. RANGE O L.E.D.
Signal Conditioning & Communications Frequency MODEL PRS1 - PLUG-IN SPEED SWITCH General Specifications 1. PRIMARY SUPPLY VOLTAGE: Available for 115 or 230 VAC ±10%, 50/60 Hz; 2.5 VA (See Ordering Information). 2. SENSOR OUTPUT POWER: +12 VDC ±5% regulated, 60 mA max. 3. OPERATING TEMPERATURE RANGE: 0 to 60°C. 4. WEIGHT: PRS1 PLUG-IN MODULE - 8 oz (226.8 g). Input Specifications 1.
Signal Conditioning & Communications Frequency MODEL PRA1 - PULSE RATE TO ANALOG CONVERTER O DELIVERS ANALOG OUTPUT PROPORTIONAL TO INPUT PULSE-RATE (Frequency) O ACCEPTS VARIABLE PULSE-RATE INPUTS FROM A WIDE VARIETY OF SENSORS O DUAL SIGNAL OUTPUT, 0 to 10 VDC PLUS SELECTABLE SIGNAL CURRENT OUTPUT OF 0 to 1 mA OR 4 to 20 mA O AVAILABLE IN 5 FREQUENCY RANGE RATINGS FROM 30 Hz to 10 KHz O ACCURACY (Linearity) 0.
Signal Conditioning & Communications Frequency MODEL PRA1 - PULSE RATE TO ANALOG CONVERTER General Specifications 1. PRIMARY SUPPLY VOLTAGE: Available for 115 or 230 VAC ±10%, 50/60 Hz; 2.5 VA (See Ordering Information). 2. SENSOR OUTPUT POWER: +12 VDC ±5% regulated, 60 mA max. 3. OPERATING TEMPERATURE RANGE: 0 to 60°C. 4. WEIGHT: PRA1 Plug-in Module: 8 oz (226.8 g); Mating 12-Pin Socket: 2 oz (56.7 g). Input Specifications 1. OPERATING FREQUENCY RANGE: From 30 Hz to 10 KHz; (See Ordering Information).
Communications Signal Conditioning & Communications MODEL ICM4 - SERIAL CONVERTER MODULE EMC COMPLIANT O ALLOWS COMMUNICATIONS BETWEEN RS-232 CONTROL EQUIPMENT AND PRODUCTS WITH RS485 SERIAL COMMUNICATIONS O WIDE DC INPUT POWER RANGE (+9 to 32 VDC) O HALF DUPLEX (RS485) AND FULL DUPLEX (RS422) O LED INDICATION FOR RXD, TXD, and POWER O UNIVERSAL MOUNTING FOOT FOR DIN RAIL INSTALLATION COMMUNICATIONS CAPABILITY Product Features Click Icon For User Bulletin FAX/WEB DOC # 12010 The ICM4 Seria
Signal Conditioning & Communications Communications MODEL ICM4 - SERIAL CONVERTER MODULE Input/Output Communications 1. RS-232 VOLTAGES: Receive Data Pin: ± 30 VDC max., Mark Condition: d 0.8 VDC Space Condition: t 2.4 VDC Transmit Data Pin: Mark Condition: -8 VDC (typ.) Space Condition: +8 VDC (typ.) 2. RS485 VOLTAGES: Differential Output Voltage: ± 5 VDC max. under no load Differential Input Voltage: ± 5 VDC max. Mark Condition: d -0.2 VDC Space Condition: t +0.
Signal Conditioning & Communications Communications MODEL GCM232 - SERIAL CONVERTER MODULE EMC COMPLIANT O ALLOWS COMMUNICATIONS BETWEEN RS-232 CONTROL EQUIPMENT AND RLC PRODUCTS WITH 20 mA SERIAL COMMUNICATIONS OPTION O ISOLATED 20 mA SERIAL COMMUNICATIONS O FULLY ENCLOSED SCREW-TOGETHER DURABLE PLASTIC CASE COMMUNICATIONS CAPABILITY Product Features Click Icon For User Bulletin FAX/WEB DOC # 12008 The GCM232 Serial Converter Module provides the capability of interfacing Red Lion Controls pro
Signal Conditioning & Communications Communications MODEL GCM422 - SERIAL CONVERTER MODULE O ALLOWS COMMUNICATIONS BETWEEN RS422 CONTROL EQUIPMENT AND RLC PRODUCTS WITH 20 mA SERIAL COMMUNICATIONS OPTION O TRANSMIT DISABLE ALLOWS OPERATION ON A TWO-WIRE BUS FOR RS485 COMPATIBILITY O ISOLATED 20 mA SERIAL COMMUNICATIONS O FULLY ENCLOSED SCREW TOGETHER DURABLE PLASTIC CASE EMC COMPLIANT COMMUNICATIONS CAPABILITY Click Icon For User Bulletin Product Features The GCM422 Serial Converter Module prov
Communications Signal Conditioning & Communications MODEL GWDN - DEVICENET™ GATEWAY MODULE EMC COMPLIANT Click Icon For User Bulletin O ALLOWS COMMUNICATIONS BETWEEN DEVICENET™ CONTROL EQUIPMENT AND PRODUCTS WITH RS485 SERIAL COMMUNICATIONS, INCLUDING MODBUS O HALF DUPLEX (RS485) AND FULL DUPLEX (RS422) O LED INDICATION FOR RXD, TXD, and DEVICENET™ STATUS O UNIVERSAL MOUNTING FOOT FOR DIN RAIL INSTALLATION COMMUNICATIONS CAPABILITY Product Features FAX/WEB DOC # 12016 The GWDN DeviceNet™ Gat
Signal Conditioning & Communications Communications MODEL GWDN - DEVICENET™ GATEWAY MODULE Input/Output Communications 1. RS485 VOLTAGES: Differential Output Voltage: ± 5 VDC max. under no load Differential Input Voltage: ± 5 VDC max. Mark Condition: d -0.2 VDC Space Condition: t +0.2 VDC RS485 Drive Capability: Up to 32 RS485 receivers connected in parallel. 2. MAXIMUM CABLE LENGTH: RS485: 4000 feet DeviceNet: Check DeviceNet™ specification Volumes I and II. 3. RS485 BAUD RATE: 300 min., 19200 max. 4.
Signal Conditioning & Communications Power Supplies MODEL PSDR6 - SIGNAL CONDITIONER 650 mA POWER SUPPLY UL RECOGNIZED USA UL RECOGNIZED CANADA EMC COMPLIANT Product Features Click Icon For User Bulletin FAX/WEB DOC# 06002 The compact PSDR power supplies are an industrial input voltage supplies with primary switched-mode regulator technology. They feature low output ripple and tight (±3%) nominal voltage tolerance. The output is electronically protected against overloads and short circuits.
Signal Conditioning & Communications Power Supplies MODEL PSDR12 - SIGNAL CONDITIONER 100 mA POWER SUPPLY EMC COMPLIANT UL RECOGNIZED USA Product Features PSDR power supplies are compact, linear and highly regulated. Well suited for use with all signal conditioning products. They feature low output ripple and tight (±4%) nominal voltage tolerance. Single isolated output power supply versions are available for galvanic separation. The power supply outputs are fused.
Power Supplies Signal Conditioning & Communications MODEL PSDR13 - SIGNAL CONDITIONER 1 A POWER SUPPLY UL RECOGNIZED USA EMC COMPLIANT Product Features FAX/WEB DOC# 10013 PSDR power supplies are compact, linear and highly regulated. They are well suited for use with all signal conditioning products. They feature low output ripple and tight (±1%) nominal voltage tolerance. The PSDR1300 power supply is fused on both the input and output with 1 A (5 u 20 mm) fuses.
Signal Conditioning & Communications Power Supplies MODEL PSDR13 - SIGNAL CONDITIONER 1 A POWER SUPPLY Input Specifications 1. INPUT POWER REQUIREMENTS: 120 VAC, +6/ -10% Max. Input Power: 55 VA Output Specifications 1. POWER OUTPUT: 24 VDC ±1% @ 1 A DC max. Ripple: <20 mV pk-pk Ordering Information MODEL NO.
Signal Conditioning & Communications Relays MODEL RS - DIN RAIL RELAY SYSTEM O TERMINAL BLOCKS WITH BUILT-IN RELAY OUTPUTS O SLIM DESIGN SAVES DIN RAIL SPACE O REPLACEABLE RELAY SAVES DOWNTIME O JUMPERS SAVE WIRING TIME Product Features Click Icon For User Bulletin FAX/WEB DOC # 10018 The RS Relay System provides a compact, modular means of adding relay outputs to any transistor output device.
Signal Conditioning & Communications Relays MODEL RS - DIN RAIL RELAY SYSTEM RSJMPR - 2-POSITION JUMPER The RSJMPR Jumper can be used to bridge connections between adjacent Relay Blocks. This avoids the tedious task of wire-jumping signals such as commons or neutrals together. The maximum current capability of the RSJMPR is 6 A. The RSJMPR is available in three different colors, and is shipped in packages of 20 pieces. General Specifications 1. MAX. CURRENT: 6 A 2. LENGTH: 0.24" (6 mm) 3.
Signal Conditioning & Communications Relays MODEL RS -DIN RAIL RELAY SYSTEM RSBARR - BARRIER The Barrier is always required at the start and end of a Relay System to provide protective separation according to VDC 0106101. The Barrier should also be used to isolate adjacent Relay Blocks with voltage potentials greater than 250 V. The RSBARR is equipped with prescored breakout points at the bridging positions so that individual bridges can pass through if needed.
Signal Conditioning & Communications Relays MODEL RLY6 - SINGLE PHASE DIN RAIL MOUNT SOLID STATE RELAY O INTEGRATED HEAT SINK O OPTICALLY ISOLATED O SOLID STATE SWITCHING O 25 A SINGLE PHASE OUTPUT RATING O 48 TO 660 VAC SWITCHING O 4 TO 28 VDC CONTROL SIGNAL O ZERO VOLTAGE TURN-ON O MOUNTS ON DIN RAIL OR DIRECTLY TO PANEL O 4000 VOLT ISOLATION O BUILT-IN SNUBBER O LED “ON” INDICATOR O CAGE CLAMP TERMINATIONS UL RECOGNIZED USA CSA CERTIFIED EMC COMPLIANT Product Features The RLY
Signal Conditioning & Communications Relays MODEL RLY6 - SINGLE PHASE DIN RAIL MOUNT SOLID STATE RELAY Output Specifications 1. OPERATING VOLTAGE RANGE: 48 to 660 VAC 2. OPERATING FREQUENCY RANGE: 47 to 63 Hz 3. MAXIMUM CONTINUOUS LOAD CURRENT: 25 ARMS (See Safe Operating Conditions) 4. SURGE CURRENT: Non-Repetitive 1 Cycle: 250 APEAK Non-Repetitive 1 Second: 100 APEAK 5. MIN. LOAD CURRENT: 50 mA 6. LEAKAGE CURRENT @ VOUT (MAX.): 8 mA 7. OVER VOLTAGE RATING: 1200 PIV 8. VOLTAGE DROP @ IOUT: 1.5 VAC 9.
Signal Conditioning & Communications Relays MODEL RLY7 - THREE PHASE DIN RAIL MOUNT SOLID STATE RELAY O INTEGRATED HEAT SINK O OPTICALLY ISOLATED O SOLID STATE SWITCHING O 30 A THREE PHASE OUTPUT RATING O 48 TO 660 VAC SWITCHING O 4 TO 28 VDC CONTROL SIGNAL O ZERO VOLTAGE TURN-ON O MOUNTS ON DIN RAIL OR DIRECTLY TO PANEL O 4000 VOLT ISOLATION O BUILT-IN SNUBBER O LED “ON” INDICATOR O CAGE CLAMP TERMINATIONS UL RECOGNIZED USA CSA CERTIFIED EMC COMPLIANT Click Icon For User Bullet
Signal Conditioning & Communications Relays MODEL RLY7 - THREE PHASE DIN RAIL MOUNT SOLID STATE RELAY Output Specifications 1. OPERATING VOLTAGE RANGE: 48 to 660 VAC 2. OPERATING FREQUENCY RANGE: 47 to 63 Hz 3. MAXIMUM CONTINUOUS LOAD CURRENT: 30 ARMS /phase (See Safe Operating Conditions) 4. SURGE CURRENT: Non-Repetitive 1 Cycle: 250 APEAK Non-Repetitive 1 Second: 100 APEAK 5. MIN. LOAD CURRENT: 50 mA 6. LEAKAGE CURRENT @ VOUT (Max.): 8 mA 7. OVER VOLTAGE RATING: 1200 PIV 8. VOLTAGE DROP @ IOUT: 1.
Signal Conditioning & Communications Relays MODEL AVMR - RELAY TERMINAL BLOCKS O 2 LAYER DOUBLE CONTACT SWITCHES FROM 1 mA TO 3 A CONTINUOUS CURRENT O ISOLATION BETWEEN INPUT AND OUTPUT OF 2 KV RMS O INPUT VOLTAGE OF 24 VAC/DC O LED TO INDICATE THE SWITCHING STATUS O DAMPING AND POLARITY PROTECTION FUNCTIONS UL RECOGNIZED USA Click Icon For User Bulletin Product Features RLC relay terminal blocks are only 6.2 mm wide, but provide a complete relay interface.
Signal Conditioning & Communications Relays MODEL AVMR - RELAY TERMINAL BLOCKS Output Specifications 1. CONTACT SIDE: Contact Type: Double Contact, Form A Contact Material: AgNi, 5mm hard gold plated Max. Contact Voltage: 250 VAC/ 30 VDC Min. Contact Voltage: 5 V Max. Inrush Current: 5 A Limiting Continuous Current: 3 A Min. Switching Current: 1 mA Max. Power Rating: 72 W 2. MECHANICAL LIFE: 20 million cycles Ordering Information MODEL NO.
Signal Conditioning & Communications Notes Red Lion 220
