Datasheet

11
6.4 MODULE 4 - SETPOINT OUTPUT PARAMETERS (4-SEtPt)
SEL
Setpoint 2
Enable
Setpoint
Select
Setpoint
Assignment
Setpoint
Output Logic
Setpoint
Output
Action
Setpoint
Value
Setpoint
Output
Time-out
SP2 Only
Setpoint
Annunciator
SPt SEL
4-SEtPt
SP2 Enb SPn ASN SPn ACt SPn tOUt SPn VAL SPn OUt SPn LIt
PPrroo
SPn P-UP
SPn StbY
Setpoint
Standby
Operation
Setpoint
Boundary
Type
SPn tYPE
Counter
Auto Reset
SPn AUtO SPn ChC
Change Display
Color with
Output State
SP2 Output
Off at SP1
Output
SP1 Output
Off at SP2
Output
SP1 OFF2 SP2 OFF1
Setpoint
Output Reset
with Manual
Reset
SPn rSt
Setpoint Output
Power-up
State
SP1 Only SP2 Only
Backlight
Unit Only
PARAMETER MENU
The Setpoint Output Parameters are only active when an optional Setpoint
Output Module is installed in the meter. Some parameters in the menu will not
appear depending on the Setpoint Assignment and Setpoint Output Action. The
Setpoint Parameter Availability chart below illustrates this.
PARAMETER DESCRIPTION
BOUNDARY
bOUNd
LATCH
LAtCH
RATE ASSIGNMENT
TIMED OUT
t-OUt
BOUNDARY
bOUNd
LATCH
LAtCH
Yes No No Yes No No
SPn VAL
Setpoint Value Yes Yes Yes Yes Yes Yes
SPn OUt
Setpoint Output Logic Yes Yes Yes Yes Yes Yes
SPn LIt
Setpoint Annunciator Yes Yes Yes Yes Yes Yes
SPn P-UP
Setpoint Output Power-up State No No Yes No No Yes
SPn tYPE
Setpoint Boundary Type No Yes No Yes Yes Yes
SPn StbY
Standby Operation (Low acting only) No Yes No Yes Yes Yes
SPn AUtO
Counter Auto Reset Yes No Yes No No No
SP1 OFF2
SP1 Output Off at SP2 (SP1 only) Yes No Yes No No No
SP2 OFF1
SP2 Output Off at SP1 (SP2 only) Yes No Yes No No No
SPn rSt
Output Reset with Manual Reset Yes No Yes Yes No Yes
SPn ChC
Change Display Color w/ Output State Yes Yes Yes Yes Yes Yes
Setpoint Output Time-out Value
TIMED OUT
t-OUt
COUNTER ASSIGNMENT (A or B) *
SPn tOUt
* BOUNDARY Setpoint Action not applicable for Counter B Assignment
Select the Setpoint Output to be programmed, starting with Setpoint 1. The
"n" in the following parameters reflects the chosen Setpoint number. After
Setpoint 1 is completely programmed, the display returns to SPt SEL. Repeat
steps for Setpoint 2 if both Setpoints are used in the application.
Select NO to exit the Setpoint programming module. The number of Setpoints
available is dependent on the Setpoint option module installed.
SETPOINT SELECT
SP2SP1NO


NO
SPt SEL
SETPOINT 2 ENABLE (SP2 Only)
Select YES to enable Setpoint 2 and access the setup parameters. If NO is
selected, the unit returns to SPt SEL and Setpoint 2 is disabled.
YESNO


NO
SP2 Enb
SETPOINT ASSIGNMENT
SETPOINT PARAMETER AVAILABILITY
Select the display to which the Setpoint is assigned.


Count A
SPn ASN
SETPOINT OUTPUT ACTION
The parameter selects the action of the Setpoint Output as described in the
chart. Boundary output action is not applicable for Counter B assignment.


LAtCH
SPn ACt
Count A Count b rAtE
LAtCH t-OUt bOUNd
SPT ACTION DESCRIPTION OUTPUT ACTIVATES OUTPUT DEACTIVATES
LAtCH
Latched Output Mode
When Count =
Setpoint
At Manual Reset
(if
SPn rSt=YES)
t-OUt
Timed Output Mode
When Count =
Setpoint
After Setpoint
Output Time-Out
bOUNd
Boundary Mode
(Low Acting Type)
Boundary Mode
(High Acting Type)
When Count 
Setpoint
When Count 
Setpoint
When Count
 Setpoint
When Count
< Setpoint