Installation & Assembly

2of3
STEP 4 - Install Fixture Chain and Ceiling
Canopy
A. Adjust the Fixture Chain (GG) to your
desired length by removing the links if
needed.
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached
to the Fixture Loop (A) and the Canopy
Chain Loop (EE), pull the supply wires
through the Fixture Chain (GG)
alternating links. After the wires are
through the Fixture Chain (GG), pull the
Supply Wires and the Ground Wire
through the Canopy Lock Ring (FF) and
the Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain (GG)
to the Fixture Loop (A) with one Quick
Link (HH). Lift the fixture and Fixture
Chain (GG) up And Attach the other end
of the Fixture Chain (GG) onto the
Canopy Chain Loop (EE) with another
Quick Link (HH). The fixture will now
hang safely. Close the chain loop at the
Ceiling Canopy Loop (EE).
D. Feed the Supply Wires and Ground Wire
through the Canopy Chain Loop (EE) and
Nipple (DD) into the Outlet Box. Cut the
wires leaving approximately 8” of wire
extending from the Outlet Box.
E. Refer to Step 5 for wire connections.
F. Raise the Ceiling Canopy (II) and Canopy
Lock Ring (FF) up the Fixture Chain (GG)
and over the Canopy Chain Loop (EE).
Tighten the Canopy Lock Ring (FF) onto
the Canopy Chain Loop (EE) until tight.
Suggested chain length for Ceiling height
:
8’ ceiling : use 9 links of chain and 2
quick links
9’ ceiling : use 19 links of chain and 2
quick links
10’ ceiling : use 29 links of chain and 2
quick links
*
DD
GG
II
Supply Wires
and Ground Wire
EE
FF
HH
HH
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 5
A
(EE) against the ceiling to determine the correct position of the
Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain
Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to
rest against the ceiling when held in place by the Canopy Lock Ring
(FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
Figure 4
STEP 6 - Install Bulbs
A. This fixture uses candelabra bulb with
standard screw base. Maximum 60 watts.
B. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready
to use. Enjoy!
Figure 6
Bulb
Socket
STEP 1 Remove Shade Assembly-
A. Remove Bulbs from Sockets.
B. Remove Fixture Body from Cage with
Shade by unscrewing Lock Screws.
STEP 2 Replace Shade-
Shade inside of the Side Arms.
C. Reassemble removed Side Arms back onto the Shade Assembly
and secure with Cup Head Screws. Tighten until snug.
Replace Shade
Cup Head
Screw
Cup Head
Screw
Lock Washer
Side
Arm
Shade
Shade Holder
Ring
Bulb
Socket
Fixture
Body
Cage with
Shade
Lock Screw
B. With one person hold fixed Side Arms, another person replace the
A. Remove two Side Arms by unscrewing Cup Head Screws on the
top and bottom of Shade Assembly.
Recommends two people for this step.