Installation & Assembly

ManualsBrandsRed Barrel Studio ManualsBlack Outdoor Hanging LightsJames Mystic Black 3 -Bulb 15.5" H Outdoor Hanging Lantern

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

EstimatedAssemblyTime:30-45 minutes

Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer service for replacement

parts.

Warnings and Cautions

1of3

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Package Contents

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling Canopy

Fixture Chain

Quick Link

BulbRecommended: (3)CandelabraBase60WMaximum.

Fixture

Loop

Cage with

Shade

Fixture Body

STEP 1 Attach parts together-

A. Thread Fixture Loop (A) onto the nipple on the top center of Fixture

Body (B). Hand tighten until snug.

B. Remove Lock Screws from top edge of

Cage with Shade (C). Insert sockets

inside of Shade. Align holes on fixture

hood to mounting holes on top edge of

the cage. Secure them together with

Lock Screws. Hand tighten until snug

with screwdrivers.

Lock

Screw

Mounting

Hole

Figure 1

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included) Tighten until snug..

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 3 Install Canopy Chain

Loop and Nipple

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one

end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one

Lock Washer (BB) over the end of

the Nipple (DD) and thread the

Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers,

thread the Hex Nut (CC) against

the Canopy Chain Loop (EE) and

hand tighten until snug.

B. Thread another Hex Nut (CC) to

the middle of the Nipple (DD).

Place another Lock Washer (BB)

over the Nipple (DD) and then

thread the Nipple (DD) into the

Crossbar (AA) until the Nipple

Step B

Step A

Figure 3

(DD) is about 0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop

Socket

Assembly Instruction

Summary of content (3 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (3) Candelabra Base 60W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
(EE) against the ceiling to determine the correct position of the Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to rest against the ceiling when held in place by the Canopy Lock Ring (FF). D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II). Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in place. STEP 4 - Install Fixture Chain and Ceiling Canopy STEP 6 - Install Bulbs Figure 6 A.
PAGE 3
4.5”Sq. 1” FINISH: MYSTIC BLACK 119” OVERALL HEIGHT ( INCLUDES 96” CHAIN AND 2 QUICK LINKS ) 2 1 15.5” 11” 8”Sq. 9.5”Sq. NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2" NO. PART NUMBER REPLACEMENT PART REQ.