Installation & Assembly

ManualsBrandsRed Barrel Studio ManualsCeiling LightsSaurav 2 - Light Simple Circle Flush Mount

PACKAGE CONTENTS

INSTRUCTION SHEET

1OF3

WARNINGS AND CAUTIONS

PREPARATION

INSTALLATION INSTRUCTIONS

WARNING:

● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by

switching off the circuit breaker or removing the fuse.

CAUTIONS:

● These instructions are provided for your safety. It is very important that they are read completely before

the installation of your fixture. We strongly recommend that a professional electrician install the fixture.

● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had

sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may

result.

● Before beginning installation of product, make sure all parts are present. Compare parts with package

contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or

operate the product. Contact customer service for replacement part.

● Estimated Assembly Time: 15 30 minutes

● Tools Required for Assembly (not included): Flathead screwdriver Phillips screwdriver, pliers, electrical

tape, wire cutters, safety glasses &3, 60 Watt, Type A Medium Base Bulbs.

● Helpful Tools (not included): Wire Strippers.

Outlet Box

Screw

Hex Nut

Crossbar

Lock Washer

Nipple

Ceiling Canopy

STEP 1:

a Locate the Crossbar and attach it to the Outlet Box

using the Outlet Box Screws not supplied

b Locate the Nipple and thread one Hex Nut onto it

about half way. Slip a Lock Washer onto it and thread

one end of the nipple into the center hole of the

Crossbar

c Position the Ceiling Canopy over the outlet box,

passing the mounting hole in the center of the Ceiling

Canopy over the end of Nipple

d Adjust the Nipple so approx 3 8 inch of the Nipple is

protruding from the mounting hole. This adjustment

may take a few tries.

e When this length is achieved, remove the Ceiling

Canopy and tighten the Hex Nut up against the

underside of the Crossbar with pliers.

().

./"

Part

Description

Crossbar

Green Ground Screw

Lock Washer

Hex Nut

Nipple

Flat Washer

Finial

Lock Ball

Lock Screw

Steel Washer

Plastic Washer

Hexagon Ring Spanner

Ceiling Canopy

Frame

Quantity

1pc

2pcs

1pc

3pcs

6pcs

1pc

O Shade

1pc

Summary of content (3 pages)

PAGE 1
INSTRUCTION SHEET PACKAGE CONTENTS Part A Description Quantity Crossbar 1pc B Green Ground Screw 1pc C Lock Washer 1pc D 2pcs E Hex Nut Nipple F Flat Washer 1pc G Finial 1pc C H Lock Ball 3pcs D I Steel Washer 6pcs J Plastic Washer Hexagon Ring Spanner 3pcs 1pc Lock Screw Ceiling Canopy 3pcs 1pc G Frame 1pc H Shade 1pc I K L M N O ! 1pc K A L B M N E F O J WARNINGS AND CAUTIONS WARNING: ● Before beginning the installation, turn off electricity at the circuit
PAGE 2
INSTALLATION INSTRUCTIONS STEP 2 : a. Thread another Hex Nut onto the other end of the nipple. Thread this Hex Nut on just enough so the inside surface of the pan rests against it. * You may have to trial fit the Ceiling Canopy one more times to insure this distance also. This Hex Nut is needed here to prevent you from crushing down the center of the Ceiling Canopy . Nipple Ceiling Canopy Hex Nut STEP 3 : * Use Wire Connectors ( not supplied ) to connect the wires . a .
PAGE 3
INSTALLATION INSTRUCTIONS STEP 7 : a . Lift the Shade with Frame upward and make the holes on the Frame over the Nipple on the ends of Support Arms . Thread Lock Balls onto Nipples and hand tighten until snug to secure the Shade with Frame . Support Arm Hole Lock Ball Shade with Frame Your installation is completed now . Restore electricity . Keep this sheet for future reference .