Install Instructions
Welcome
Thank you for choosing TripleGuard. TripleGuard SMART is the ultimate IoT cloud-based system
for home safety. The system is managed via an App and is designed to prevent damage due to
water leakage. TripleGuard offers you total peace of mind at home or away.
Please Note
Please read these instructions carefully and follow the system’s installation and commissioning
steps. Maintain this document in a safe place for future reference. Contact your authorized
installer with any questions.
WARNING! This product was designed to prevent water leakage damages and should be
used for this purpose only.
TripleGuard SMART
TripleGuard’s line of products includes innovative battery-operated devices which enables
the automated control of water valves. This unies under the “Smart Home” umbrella. The
TripleGuard HUB serves as a Gateway that ensures a secured communication between the
system devices, TripleGuard™ Leak Detector cloud, and App.
TripleGuard SMART integrates easily into the Smart Home IoT ecosystem, providing a unique
cloud-based secured platform for Water Leak Management.
TripleGuard Water Leak Detector Specication:
Avoid Installing the Water Leak Detector in:
• Metal cabinets
• Dusty places
• Where the temperature exceeds -4°F to +122°F (-20°C and 50°C)
• Where it can be hit or damaged
• Outdoor, Exposed to rain and direct sunlight
• High level of humidity
Water Leak Detector Description
A. LED indicator
B. Electrodes
C. Body
D. Wall mounting tting
Leak Detector Installation
1. Open the battery housing cover by sliding it down.
2. Remove the cover and expose the battery housing to insert batteries.
3. Insert the batteries.
4. Close the battery housing cover.
5. Place the Leak Detector at a height where only the electrodes are in contact
with water during a leak.
6. Fix the Detector to the wall using the double-sided adhesive tape.
The bottom part might be xed using two screws (not included).
7. After the installation, check that the LED indicator is visible.
Leak Detector LED Behavior
• RED ashes every 10 seconds – water leak detection
• GREEN ashes every 30 seconds – OK
• BLUE ashes every 30 seconds – communication problems
• RED ashes every 30 seconds – low battery
Leak Detector Buzzer Behavior
In case of a leak, the buzzer will sound every 10 seconds.
System Installation
TripleGuard devices are installed and activated using the TripleGuard™ Leak Detector App
available on AppStore and Google Play.
This Water Leak Detector is designed for internal use only and should be installed by an
authorized plumber.
Warranty Instructions
Please visit www.rectorseal.com/tripleguard-support for warranty, technical support, terms, and
conditions or troubleshooting. RectorSeal, LLC warrants the TripleGuard (product only) to be free
of defects in workmanship, and material for a period of up to one year from date of purchase.
TripleGuard Leak Detector Installer Guide
Product 97718
RectorSeal
2601 Spenwick Drive - Houston, TX 77055 800-231-3345 rectorseal.com
RectorSeal, the logos and other trademarks are property of RectorSeal, LLC, its afliates or its licensors and are protected by copyright, trademark and other intellectual property laws,
and may not be used without permission. RectorSeal reserves the right to change specications without prior notice. © 2018 RectorSeal. All rights reserved. R50310-0918
C
A
B
D
Part Code 97710
Product Description
The wireless and battery-operated Water Leak Detector is
installed in places where high chance of water leak may occur.
Whenever water is detected, an automatic command is sent to
the TripleGuard HUB.
Dimensions
Body: 2.56 x 1.57 x 5.51 inches (6.5 x 3.99 x 14 cm)
Electrodes: 1.34 x 0.63 x 0.43 inches (34 x 16 x 11 mm)
Cable length: 1 feet (30 cm)
Weight 0.24 lbs (108.86 g)
Power Supply 2x AAA non-rechargeable batteries
Operation Voltage 3V
Battery Life Span
Up to two years. Manufacturer recommends to visually inspect
batteries every year.
Operating RF 868/915 MHz
Transmission Range
Open space - up to 750 ft. (230 m)
In enclosed space - up to 390 ft. (120 m)
Avoid installing in a metal cabinet.
Certications
FCC ID: 2AFOICLMFLD10
IC: 20798-CLMFLD10
Working Temperature -4°F to +122°F (-20°C to +50°C)