Datasheet

ManualsBrandsRecom ManualsBoard Mounted DC / DC ConvertersDC/DC Converter 10W 5V 2A

10 Watt

1“x1“

Single & Dual

Output

Features

Regulated

Converters

• 2:1 wide input voltage range

• 1.6kVDC isolation

• UL60950-1 certiﬁed

• Efﬁciency up to 91%

• Six-sided continuous shield

• No minimum load required

PD-1

REV.: 3/2018www.recom-power.com

DC/DC Converter

Description

The RP10-A series are wide input voltage range 1”x1” power DC/DC converters. Despite their small

size, the RP10-A converters are fully speciﬁed devices with built-in Class A EMC ﬁlters, no minimum

load, 1.6kVDC isolation, under-voltage lockout and low ripple/noise ﬁgures. The outputs are fully

protected against short circuits, overcurrent and overvoltage and can be trimmed over a ±10% range.

The RP10-A series will ﬁnd many uses in applications where board space is at a premium as no

external components are required.

E196683

RP10-A

Selection Guide

Part Number Input Output Output Input

(1)

Efﬁciency

(1)

Max. Capacitive

Voltage Range Voltage Current Current typ. Load

[VDC] [VDC] [mA] [mA] [%] [µF]

RP10-123.3SA

(2,3)

9-18 3.3 3000 994 83 3500

RP10-1205SA

(2,3)

9-18 5 2000 969 86 2500

RP10-1212SA

(2,3)

9-18 12 830 933 89 430

RP10-1215SA

(2,3)

9-18 15 670 931 90 350

RP10-1224SA

(2,3)

9-18 24 416 914 91 125

RP10-243.3SA

(2,3)

18-36 3.3 3000 485 85 3500

RP10-2405SA

(2,3)

18-36 5 2000 484 86 2500

RP10-2412SA

(2,3)

18-36 12 830 456 91 430

RP10-2415SA

(2,3)

18-36 15 670 465 90 350

RP10-2424SA

(2,3)

18-36 24 416 457 91 125

RP10-483.3SA

(2,3)

36-75 3.3 3000 243 85 3500

RP10-4805SA

(2,3)

36-75 5 2000 239 87 2500

RP10-4812SA

(2,3)

36-75 12 830 230 90 430

RP10-4815SA

(2,3)

36-75 15 670 233 90 350

RP10-4824SA

(2,3)

36-75 24 416 229 91 125

RP10-1205DA

(2,3)

9-18 ±5 ±1000 969 86 ±1440

RP10-1212DA

(2,3)

9-18 ±12 ±416 935 89 ±250

RP10-1215DA

(2,3)

9-18 ±15 ±333 925 90 ±180

RP10-2405DA

(2,3)

18-36 ±5 ±1000 484 86 ±1440

RP10-2412DA

(2,3)

18-36 ±12 ±416 462 90 ±250

RP10-2415DA

(2,3)

18-36 ±15 ±333 463 90 ±180

RP10-4805DA

(2,3)

36-75 ±5 ±1000 239 87 ±1440

RP10-4812DA

(2,3)

36-75 ±12 ±416 229 91 ±250

RP10-4815DA

(2,3)

36-75 ±15 ±333 231 90 ±180

UL60950-1 Certiﬁed

Ordering Examples

RP10-2405SA/P = 24V Input, 5V Output, Positive Logic CTRL pin and Trim pin ﬁtted

RP10-4805DA/XC-HC = 48V Input, ±5V Output, without CTRL pin, with ﬁtted Heat-sink

RP10-2405SA/N = 24V Input, 5V Output, Negative Logic CTRL pin and Trim pin ﬁtted

Model Numbering

Notes:

Note2: standard part is with sufﬁx “P” for positive logic (1=ON, 0=OFF) and trim pin

add sufﬁx “N” instead for negative logic (0=ON, 1=OFF) and trim pin

or add sufﬁx “XC” instead for no CTRL pin

Note3: add sufﬁx “-HC” for premounted Heat-sink with clamps

Notes:

Note1: Measured at nominal input voltage and full load

Input Voltage

Output Voltage

Single or Dual

RP10-__ __ _A/_- __

Package

(3)

CTRL Logic

(2)

Summary of content (7 pages)

PAGE 1
Features Regulated Converters • • • • • • 2:1 wide input voltage range 1.6kVDC isolation UL60950-1 certified Efficiency up to 91% Six-sided continuous shield No minimum load required DC/DC Converter RP10-A Description The RP10-A series are wide input voltage range 1”x1” power DC/DC converters. Despite their small size, the RP10-A converters are fully specified devices with built-in Class A EMC filters, no minimum load, 1.6kVDC isolation, under-voltage lockout and low ripple/noise figures.
PAGE 2
RP10-A DC/DC Converter Series Specifications (measured at Ta = 25°C, nominal input voltage, full load otherwise noted) BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Internal Input Filter Pi-Type Input Voltage Range nom. Vin = 12V nom. Vin = 24V nom. Vin = 48V Input Surge Voltage Vin = 12V, 1s max. Vin = 24V, 1s max. Vin = 48V, 1s max.
PAGE 3
RP10-A DC/DC Converter Series Specifications (measured at Ta = 25°C, nominal input voltage, full load otherwise noted) External Output Trimming Output Voltage Trimming Single output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for chosing these trimming resistors.
PAGE 4
RP10-A DC/DC Converter Series Specifications (measured at Ta = 25°C, nominal input voltage, full load otherwise noted) RP10-xx24SA Trim up 1 2 3 4 5 6 7 8 9 10 Vout = 24.24 24.48 24.72 24.96 25.20 25.44 25.68 25.92 26.16 26.40 Volts 570.333 278.667 181.444 132.833 13.667 84.222 70.333 59.917 51.815 45.333 kOhms RU = % Trim up 11 12 13 14 15 16 17 18 19 20 Vout = 26.64 26.88 27.12 27.36 27.60 27.84 28.08 28.32 28.56 28.80 Volts RU = 40.030 35.
PAGE 5
RP10-A DC/DC Converter Series Specifications (measured at Ta = 25°C, nominal input voltage, full load otherwise noted) ENVIRONMENTAL Parameter Condition Value -40°C to +78°C -40°C to +100°C without derating with derating Operating Temperature Range Maximum Case Temperature +105°C Temperature Coefficient ±0.02%/°C max. Thermal Impedance without Heat-sink with Heat-sink natural convection 0.1m/s (20LFM) 18.2°C/W 15.
PAGE 6
Fuse DC DC/DC Converter Specifications RP10-A +VOUT +VIN Input LOAD C1 DC (measured at Ta = 25°C, nominal input voltage, full load otherwise noted) -V Series -VOUT IN EMI Filtering Class B +VIN Input DC DC C1 LOAD C1 +VOUT LOAD +VIN Input MODEL Fuse +VOUT GND DC DC -VOUT -VOUT -VIN LOAD Fuse -VIN Fuse C1 RP10-12xxS_DA 10μF/25V 1812 MLCC RP10-24xxS_DA 6.8μF/50V 1812 MLCC RP10-48xxS_DA 4.
PAGE 7
RP10-A DC/DC Converter Series Specifications (measured at Ta = 25°C, nominal input voltage, full load otherwise noted) Dimension Drawing with heat sink (mm) 25.4 25.4 Top View Heat-sink 24.2 5.85 31.4 5.6 16.5 9.9 Pin Connections 2.54 Ø 1.0±0.1 8 x 2.54= 20.32 Recommended Footprint Details 2 Bottom View 3 5 1 Dual “XC-HC“ 1 +Vin +Vin +Vin 2 -Vin -Vin -Vin 3 CTRL(2) CTRL(2) no Pin 4 +Vout +Vout +Vout 5 Trim Com Com 6 -Vout -Vout -Vout Pin Pitch Tolerance ±0.