Datasheet

RCD-24
Voltage Control (0-15V max)
Output Current
100%
0%
1V
2V
3V 4V 15V
0.13V
4.35V
Analogue Input Voltage
10V
300, 700, 1200mA
4.2V
1000mA
1
0
PWM Digital Control Signal
Output Current (LED appears dim)
200Hz
Typ.
LIGHTLINE
DC/DC-Converter
RCD-24
Series
Specifications (typical at 25°C, nominal input voltage, rated output current unless otherwise specified )
Operating Temperature Range 300mA-350mA -40°C to +85°C
(free air convection) 500mA -40°C to +80°C
600mA -40°C to +75°C
700mA-1000mA -40°C to +71°C
1200mA -40°C to +65°C
Storage Temperature Range -55°C to +125°C
Maximum Case Temperature 100°C
Thermal Impedance Natural Convection 55°C/Watt
Case Material (Pinned or Wired Versions) Non Conductive Black Plastic
Potting Material (Pinned or Wired Versions) Epoxy (UL94-V0)
Dimensions Pinned/Wired 22.1 x 12.6 x 8.5mm
Weight Pinned/Wired 4.5g/6.8g
Soldering Profile Pinned 265°C/10 sec. max
Packing Quantities Pinned Versions 39pcs per Tube
(Refer to App Notes for Tube sizes) Wired Versions 5pcs per Bag
PWM Dimming and ON/OFF Control (Leave open if not used - do not tie to +Vin)
Remote ON/OFF DC/DC ON 300mA-700mA Open or 0V<Vr<0.6V
Threshold Voltages 1000mA-1200mA Open or 0V<Vr<0.8V
DC/DC OFF (Standby) 300mA-700mA 0.6<Vr<2.9V
1000mA-1200mA 1.4<Vr<2.2V
DC/DC OFF (Shutdown) 300mA-700mA 2.9V<Vr<6V
1000mA-1200mA 2.2V<Vr<15V
Remote Pin Drive Current Vr=5V 1mA max
Quiescent Input Current in Shutdown Mode Vin=36V 200μA max
Maximum PWM Frequency For Linear Operation 200Hz max.
Frequency Limit 1000Hz max.
Analogue Dimming Control (leave open if not used - do not tie to +Vin)
Input Voltage Limits Standard -0.3V - 15V
Vref Version -0.3V - 5V
Control Voltage Range Full On 0.13V ± 50mV
(see Graphs) 300, 700, 1200mA: Full Off 4.2V ± 150mV
1000mA: Full Off 4.35V ± 100mV
Vref Version: Full Off 2.6V ± 100mV
Analogue Pin Drive Current Vc=5V 0.2mA max.
Vref Version Vref Voltage 3.3V± 70mV
Vref Output Current 5mA
Vref Output Short Circuit Current 18mA typ.
Environmental
Relative Humidity 5% to 95% RH, non-condensing
/W Versions IP67
Shock / Vibration EN61373
EMC Railways EN50121-3-2:2006
Conducted Emissions (with filter, see note) EN55022 Class B
Radiated Emissions (all series except >700mA) EN55022 Class B
ESD EN61000-4-2 Criterion A
Radiated Immunity EN61000-4-3 Criterion A
Fast Transient EN61000-4-4 Criterion A
Conducted Immunity EN61000-4-6 Criterion A
MTBF (RCD-24-0.70, Nominal Vin, Full Load) +25°C 605 x 10³ hours
using MIL-HDBK 217F +71°C 516 x 10³ hours
Safety Standards EN General Safety Report: SPCLVD1109081EN60950-1 2nd Edition
EMC Railway Report: 12A082105E-C EN50121-3-2
UL General Safety Report: E358085-A3 UL60950-1
CSA C22.2 No 60950-1-03
Analogue Dimming
Digital Dimming
Output Current (LED appears bright)
PWM Digital Control Signal
1
0
200Hz
Typ.
Combined PWM and Analogue Dimming
0
1
Max*
0
PWM Digital Control Signal
Output Current
* Max output current can also be set using Analogue input
Voltage Control (0-5V max)
Output Current
100%
0%
1V
2V
3V
4V
5V
0.13V
2.6V
Vref Version Analogue Input Voltage
Standard Version:
Vref Version:
Note:
1. Requires an input filter to meet EN55022 Class B conducted emissions - see next page
2. All LED Drivers may not be used without a load. They must be switched on the primary side only.
Noncompliance may damage the LED or reduce its lifetime.
L-4 www.recom-power.comREV: 1/2016