Datasheet

ManualsBrandsRecom ManualsLED DriversLED Driver 21W 350mA 59V IP20

Features

LED

Driver

• Low proﬁle case (13mm height max.)

• 350mA to 700mA constant current outputs

• Terminal block input/output with cable clamps

• Fully protected (OLP, SCP, OCP, OTP)

• Suitable for Class I and Class II luminaires

• Low cost

Description

These low proﬁle constant current LED drivers have been designed for cost-sensitive applications.

The SELV outputs are suitable for both independently supplied or built-in power-supply LED luminaires.

Their low proﬁle design allows them to be invisibly built into furniture, discreetly mounted under shelves

or integrated in space-restricted applications such as coving lighting, strip lighting or troffer lighting sys-

tems. The power supplies are short circuit and overload protected and come with a full 3-year warranty.

RACD20-LP

AC/DC Converter

www.recom-power.com

REV.: 1/2019 L-1

20 Watt

Constant

Current

Single

Output

ERP

compliant

IEC/EN61347-1 certiﬁed

IEC/EN61347-2-13 certiﬁed

ENEC certiﬁed

CB report

EN55015 compliant

BASIC CHARACTERISTICS

Parameter Condition Min. Typ. Max.

Input Voltage Range 198VAC 230VAC 264VAC

Inrush Current 8.0A

Start-up Time 500ms

Input Frequency Range 47Hz 63Hz

No Load Power Consumption 0.5W

Power Factor full load, 230VAC 0.55

Internal Operating Frequency full load 45kHz 140kHz

Output Ripple Current

(1)

50mAp-p

Speciﬁcations (measured @ Ta= 25°C, 240VAC and rated load)

REGULATIONS

Parameter Condition Value

Output Accuracy ±5% max.

Line Regulation 5% max.

Load Regulation 5% max.

Notes:

Note1: Measured at 20MHz Bandwidth using 0.1µF & 47µF parallel capacitor

Selection Guide

Part Input Input Output Output Efﬁciency Output

Number Voltage Range Current Voltage Range Current typ. Power max.

[VAC] [mA] [VDC] [mA] [%] [W]

RACD20-350-LP 198-264 210 2-59 350 86 21W

RACD20-500-LP 198-264 210 2-40 500 85 20W

RACD20-700-LP 198-264 210 2-31 700 85 22W

All LED Drivers may not be used without a load. They must be switched on the primary side only.

Noncompliance may damage the LED or reduce its lifetime.

Summary of content (4 pages)

PAGE 1
• Low profile case (13mm height max.) Features • 350mA to 700mA constant current outputs • Terminal block input/output with cable clamps LED Driver AC/DC Converter • Fully protected (OLP, SCP, OCP, OTP) • Suitable for Class I and Class II luminaires RACD20-LP • Low cost Description These low profile constant current LED drivers have been designed for cost-sensitive applications. The SELV outputs are suitable for both independently supplied or built-in power-supply LED luminaires.
PAGE 2
RACD20-LP AC/DC Converter Series Specifications (measured @ Ta= 25°C, 240VAC and rated load) PROTECTION Parameter Condition Input Fuse Value external fuse is recommended T1A Open Circuit Protection (OCP) auto recovery after fault condition is removed Over Load Protection (OLP) auto recovery after fault condition is removed Over Voltage Protection (OVP) auto recovery after fault condition is removed Over Temperature Protection (OTP) 110°C Tcase Isolation Voltage auto recovery after fault con
PAGE 3
RACD20-LP AC/DC Converter Series Specifications (measured @ Ta= 25°C, 240VAC and rated load) SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report Number Standard Lamp controlgear Part 1: General and safety requirements (CB Scheme) 305985 IEC61347-1:2007 2nd Edition + A2:2012 Lamp controlgear Part 2-13: Particular requirements for d.c. or a.c.
PAGE 4
RACD20-LP AC/DC Converter Series Specifications (measured @ Ta= 25°C, 240VAC and rated load) 52.0 PRI SEC 3 2 4 50.0 tc 1 FC 44.0 18.0 Dimension Drawing (mm) wire preparation 6-7mm M3 Screws FC 115.0 50.0 Connection via Screw Terminal # 1 2 3 4 Function Solid Wire VAC in (N) 0.75-1.5mm² VAC in (L) 0.75-1.5mm² LED+ 0.5-1.5mm² LED0.5-1.5mm² Stranded Wire (2) 0.75-1.5mm² 0.75-1.5mm² 0.5-1.5mm² 0.5-1.