Datasheet

ManualsBrandsRecom ManualsLED DriversLED Driver 6W 500mA 12V IP20

Features

LED

Driver

• Low proﬁle case (11mm height max.)

• 350mA to 700mA constant current outputs

• Terminal block input/output with cable clamps

• Fully protected (OLP, SCP, OCP, OTP)

• Low standby power, ErP conform

• Low cost

Description

These low proﬁle constant current LED drivers have been designed for cost-sensitive applications.

The SELV outputs are suitable for both independently supplied or built-in power-supply LED luminaires.

Their low proﬁle design allows them to be invisibly built into furniture, discreetly mounted under shelves

or integrated in space-restricted applications such as coving lighting, strip lighting or troffer lightingsys-

tems. The power supplies are short circuit and overload protected and come with a full 3-year warranty.

RACD06-LP

AC/DC Converter

www.recom-power.com

REV.: 2/2019 L-1

6 Watt

Constant

Current

Single

Output

ERP

compliant

IEC/EN61347-1 certiﬁed

IEC/EN61347-2-13 certiﬁed

ENEC certiﬁed

CB report

EN55015 compliant

Selection Guide

Part Input Input Output Output Efﬁciency Output

Number Voltage Range Current Voltage Range Current typ. Power max.

[VAC] [mA] [VDC] [mA] [%] [W]

RACD06-350-LP 198-264 80 2-18 350 77 6

RACD06-500-LP 198-264 80 2-12 500 75 6

RACD06-700-LP 198-264 80 2-9 700 74 6

BASIC CHARACTERISTICS

Parameter Condition Min. Typ. Max.

Input Voltage Range 198VAC 230VAC 264VAC

Inrush Current 11.0A

Start-up Time 100ms

No Load Power Consumption 0.4W

Input Frequency Range 47Hz 63Hz

Power Factor full load, 230VAC 0.55

Internal Operating Frequency full load 60kHz 140kHz

Output Ripple Current

(1)

50mAp-p

Speciﬁcations (measured @ Ta= 25°C, 240VAC and rated load)

All LED Drivers may not be used without a load. They must be switched on the primary side only.

Noncompliance may damage the LED or reduce its lifetime.

REGULATIONS

Parameter

Condition

Value

Output Accuracy ±5% max.

Line Regulation 5% max.

Load Regulation 5% max.

Notes:

Note1: Measured at 20MHz Bandwidth using 0.1µF & 47µF parallel capacitor

Summary of content (4 pages)

PAGE 1
• Low profile case (11mm height max.) Features • 350mA to 700mA constant current outputs • Terminal block input/output with cable clamps LED Driver AC/DC Converter • Fully protected (OLP, SCP, OCP, OTP) • Low standby power, ErP conform RACD06-LP • Low cost Description These low profile constant current LED drivers have been designed for cost-sensitive applications. The SELV outputs are suitable for both independently supplied or built-in power-supply LED luminaires.
PAGE 2
RACD06-LP AC/DC Converter Series Specifications (measured @ Ta= 25°C, 240VAC and rated load) PROTECTION Parameter Condition Input Fuse Value external fuse is recommended T1A Open Circuit Protection (OCP) auto recovery after fault condition is removed Over Load Protection (OLP) auto recovery after fault condition is removed Over Voltage Protection (OVP) auto recovery after fault condition is removed Over Temperature Protection (OTP) 110°C Tcase Isolation Voltage auto recovery after fault con
PAGE 3
RACD06-LP AC/DC Converter Series Specifications (measured @ Ta= 25°C, 240VAC and rated load) SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report Number Lamp controlgear Part 1: General and safety requirements (CB Scheme) Standard IEC61347-1:2015+A1:2017, 3rd Edition 374931 Lamp controlgear Part 2-13: Particular requirements for d.c. or a.c.
PAGE 4
RACD06-LP AC/DC Converter Series Specifications (measured @ Ta= 25°C, 240VAC and rated load) 3 PRI SEC FC 40.0 tc 39.5 1 4 2 46.0 15.5 Dimension Drawing (mm) wire preparation M3 Screws 6-7mm FC 85.0 98.0 2 mounting screws are included 11.0 2.0 46.0 Connection via Screw Terminal # 1 2 3 4 Function Solid Wire VAC in (N) 0.75-1.5mm² VAC in (L) 0.75-1.5mm² LED+ 0.5-1.5mm² LED0.5-1.5mm² Stranded Wire (2) 0.75-1.5mm² 0.75-1.5mm² 0.5-1.5mm² 0.5-1.