Mini Stand-Alone 1 Ch / 2 ~ 4 Ch Sequence View & Record Mobile DVR User Manual (104CF-A) Please read this user manual completely before operating this DVR system and keep it in a safe place for future reference.
TABLE OF CONTENTS Table of Contents ……………………………………………………………………… 1 Introduction …………………………………………………………………………….. 2 Important Safety Information ………………………………………………………… 2 Unpacking Your System ……………………………………………………………… 3 Control Panel and Function ……………………………………………….…………. 5 Installation ……………………………………………………………………………… 7 Before Operation ……………………………………………………………………… 9 Operation ………………………………………………………………………………. 10 OSD (On Screen Display) Menu Setting Operation Process …………………..
INTRODUCTION Thank you for purchasing our unique DVR system. To ensure that you optimize the full capabilities of this product, please read this user’s manual before proceeding. Be sure to keep this manual for future reference in case any problems or questions should arise. We hope you enjoy your new DVR system. IMPORTANT SAFETY INFORMATION When using your DVR equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.
UNPACKING YOUR SYSTEM Your DVR system will include the followings: 1 x Mini DVR 1 x DC connector 1 x Key on/Key start cord 2 x Cover for Key on/Key start wire 1 x DC power cord 2 x Fuse 1 x RCA A/V connector 1 x Sensor control wire 1 x A/V Input connector 1 x IR Remote Control 1 x User’s Manual 3
Optional Accessories CF Card Car rear view camera Car rear view camera CCD color dome camera Shatter proof CCD color dome camera Motion detector (Sensor) Alarm 4
CONTROL PANEL AND FUNCTION Front Panel 1. 2. 3. 4. Power indicator CF card slot CF card indicator IR remote control receiver Rear Panel 5. 6. 7. 8. Power On/Off switch Audio output terminal Video output socket Mode 1/Mode 2 select switch 9. DC input socket 10. RS-232 signal to DVR socket 11. Sensor input socket 12.
IR Remote Control 1. Power On/Off button 2. Menu button 3. Record button 4. PTZ button 5. Up key (Camera 1) 6. Down key (Camera 3) 7. Left key (Camera 2) 8. Right key (Camera 4) 9. Select button 10. Play button 11. Fast forward button 12. Fast back button 13. Pause button 14. Audio 1 button 15. Audio 2 button 16. Audio Mute button 17. Zoom in button 18. Zoom out button 19. PTZ auto button 20.
Installation DVR Installation Please refer to the installation process as the following drawing: 1. CF Card installation Insert the CF card into the CF card slot of the DVR. 2. Audio output connection Connect audio output to TV audio input. 3. Video connection Connect the monitor to Video output terminal. 4. Mode 1 or Mode 2 select switch Mode 1: 2~4 channels sequencing view & record. Mode 2: One channel real time recording.
5. System Camera installation Connect one end of camera cable to Camera and the other end to Video Input terminal at the back of DVR. Please number the camera by yourself for convenient operation. 6. Detecting wire (Sensor control) connection If you select Mode 2, you can also connect the detecting wire for switching record. Connect the detecting wire to this socket. Please refer to the following drawing as for the connecting.
BEFORE OPERATION (1) The system will auto detecting the hardware and enter Recording mode while hardware is in normal condition. (2) The system will show [UNKNOW HDD] then enter [Format Menu] within 3 seconds when first time start the system or CF card is changed. Please select [FORMAT HDD YES] to format CF card. The system will auto enter record mode after format CF card. (Or, enter the Main menu “record setup” and select HDD information to format the CF card.
OPERATION The system is preset [KEY LOCK] mode [OFF], when the system setting [KEY LOCK] mode [ON], the screen will show below message: PASSWORD： ＊＊＊＊ Please key in the security code by remote control number keys to enter the OSD manual for setting. OSD (On Screen Display) Menu Setting Operation Process 1. Press [ ] to enter menu selection mode. 2. Press up [ 3. Press ] key or down [ ] key to select the item for setting. key to enter sub menu to select item for setting. 4.
(Down Key) Go Down (Left Key) Go Left (Right Key) Go Right (Enter Key) ENTER next page 2、 Play operation key Key Operation PLAY PLAY FF FAST FORWARD FB FAST BACK P/S PAUSE / STOP Remarks 3、 REC operation key Key REC Operation Remarks RECORD 4、 PTZ control key operation Key Operation PTZ PTZ IN ZOOM IN OUT ZOOM OUT Remarks 1. Press key to enter the function. 2. Press function key to operate. 3. Press direction to select the area.
The DVR system is preset to work in Mode 2. If you want to change it to Mode 1, please switch the select switch to Mode 1. (The select switch is at the back of DVR.) When the DVR system is power ON and on record mode, 1. Press FF key two times, FB key two times and (Select) key two times. Then, the following screen will be showed. If there are 2 channels or 1 channel selected, then the other cameras setting under MENU will not function.
[M]: Motion recording [A]: Alarm [R]: Overwriting enabled. [O]: Overwriting is not allowed. 99%: The percentage of HDD recording space. OSD Setting Operation 1. Title Setup Operation A. Press key to enter menu selection mode. MAIN TITLE SETUP DATE/TIME VIDEO SETUP MOTION DETECT EVENT LIST AUTO SEQUENCE RECORD SETUP SYSTEM SETUP PERIPHERAL SETUP KEY LOCK：OFF NETWORK CF /HDD LOCK: ON B. Use / key to select [TITLE SETUP] setting section. key to enter channel select mode. C.
F. Use / key to select alphabet (A~Z) or digital (0~9) for title, maximum 4 alphabet or digits can be setting for one channel title. key to exit for select other channel or press G. Press than 2 seconds to exit OSD setting operation. key and keep more 2. Date / Time & Daylight Saving Time Setting A. Date/Time Setting a. Press key to enter menu selection mode. b. Use / c. Press key to select [DATE/TIME] setting section. key to enter [DATE/TIME] setting mode.
DAYLIGHT SAVING TIME TURN: OFF START TIME MONTH DAY HOUR END TIME MONTH DAY HOUR : 04 : 02 : 02 : 10 : 29 : 02 G. Use / key to select area for setting. H. Use / key to select value for setting. I. Press key to exit for select other setting mode or press more than 2 seconds to exit OSD setting operation. 3. Video Setup A. Press B. Use key to enter menu selection mode. / C. Press key to select [VIDEO SETUP] setting section. key to enter [VIDEO SETUP] select mode.
VIDEO SETUP CH1 BRIGHTNESS： 36 (00~63) CONTRAST： 36 (00~63) SATURATION： 36 (00~63) HUE： 36 (00~63) APPLY TO ALL a. Brightness: Brightness is adjustable, “00” = the darkest, “63” = the lightest. b. Contrast: Contrast is adjustable, “00” = maximum, “63” = minimum. c. Saturation: Saturation is adjustable, “00” = maximum, “63” = minimum. d. Hue: Hue is adjustable, “00” = maximum, “63” = minimum. e.
MOTION DETECTION_CH1 TURN： ：ON (or OFF) RELAY OUTPUT: ON (or OFF) key to exit for select other setting mode or press F. Press more than 2 seconds to exit OSD setting operation. key and keep 5. Event List Selection A. Press B. Use key to enter menu selection mode. / key to select [EVENT LIST] setting section. C. Press key to enter [EVENT LIST] select mode.
6. Auto Sequence Setting A. Press key to enter menu selection mode. B. Use / key to select [AUTO SEQUENCE] setting section. C. Press key to enter [AUTO SEQUENCE] select mode. AUTO SEQUENCE CH01: ON CH02: ON CH03: ON CH04: ON TIME INTERVAL: 5.0 B. Use / key to select channel for auto sequence view. C. Use / key to turn On for view or turn Off for not viewing. F. / Press key to select view each channel time. G. Use / key to select the time to view each channel (0.25 / 0.5 / 0.75 / 1.0 / 1.
E. Press Key to enter selected section for setting, then use select the section for setting and use / / key to key to select the value. a. Record Mode set up: 3 record modes (“C” = Continuous, “A” = Alarm and “M” = Motion) for select. SCHEDULE RECORD AM PM 0 — — 3 — — 6 — — 9 — — C C C C C C C C C C C C 12 — — 15 — — 18 — — 21 — — C C C C C C C C C C C C b. Continuous Record: for set-up 4 level record quality and 4 kinds frame rate for record.
c. Alarm / Motion Record: for set-up 4 level record quality, 10 kinds frame rate and duration for record while detect alarm or motion. ALARM/MOTION RECORD RESOLUTION: CIF QUALITY: STANDARD REC TIME: 60 REC RATE: 30_FPS SENSITIVITY: 04 * Resolution: 0.25CIF / CIF / 2CIF * Quality: Standard / Super / High / Normal. * REC Time: 10~99 (seconds) * REC Rate: Set up frame per second (fps) as below NTSC: 30 / 15 / 8 / 4 (fps) PAL: 25 / 12 / 8 / 4 (fps) * Sensitivity: 01 ~ 10 (10 = the highest) d.
* Set “ALARM/MOTION RECORD” mode and then select “PRE-RECORD: ON”. The system will record 100 images in the hard disk before event detected motion. F Press key to exit for other setting or press seconds to exit OSD setting operation. key and keep more than 2 8. System Setup Operation A. Press B. Use key to enter menu selection mode. / C. Press key to select [SYSTEM SETUP] setting section. key to enter [SYSTEM SETUP] select mode.
b. Password: for change pass word. (initial password: 0000) PASSWORD： c. PTZ: for setting protocol, baud rate. PTZ PROTOCOL： ： PELCO-D BAUD RATE： 9600 * Protocol: PELCO-D / PELCO-P * Baud Rate: 2400 / 4800 / 9600 / 19200 d. Audio: for turn on or off audio record. AUDIO SETUP AUDIO REC： ：ON (or OFF) e. Display information: for display Channel Name, Record Mode, HDD Mode, HDD Space, Date and Time on the screen.
* Device: GPS / DIAL * Baudrate: 2400 / 4800 / 9600 / 14400 / 19200 / 38400 / 57600 / 115200 * Dial mode: TONE / PULSE g. DVR ID: for setting DVR ID number. DVR ID ID TYPE: ID ID: 0000 ID TYPE: ID / BUS / TAXI / TRAIN h. Factory default: for setting load default yes or no. When you press Key, the DVR will go back to factory default. The screen will show “FACTORY DEFAULT OK!”. i. Update code from CF card: Please contact your distributor for more information if this DVR got problem. 9.
value for setup. key to exit for other setting or press E. Press second to exit OSD setting operation. key and keep more than 2 10. Key Lock Function Setting Operation A. Press B. Use key to enter menu selection mode. / key to select key lock function on or off. C. Press / key to select other section for setting or press OSD menu setting function. key to exit 11. Network Setting Operation (optional) (This function is available when the DVR is connected with LAN) A. key to enter menu selection mode.
12. CF / HDD LOCK: ON Function Setting B. Press key to enter menu selection mode. MAIN TITLE SETUP DATE/TIME VIDEO SETUP MOTION DETECTION EVENT LIST AUTO SEQUENCE RECORD SETUP SYSTEM SETUP PERIPHERAL SETUP KEY LOCK：ON/OFF NETWORK CF /HDD LOCK: ON B. Use / key to select the [CF / HDD lock] on or off. C. Press / key to select other section for setting or press OSD menu setting function.
PLAY BACK RECORD DATA There are two ways to playback the record data. 1. Playback by Time: Press the “Play” button, the screen will display playback menu, you can use up/down/right/left/enter buttons to select the start day and time which you want to play back, then move to “PLAY” and press “Enter” button to playback. PLAYBACK： 1.TIME: 2006/12/26 12:26 PLAY 2. EVENT: LIST HDD FILE BEGIN 06/12/26 08:26 END 06/12/26 16:20 2. Playback by Event: 4.
PTZ CAMERA SETTING AND CONTROL 1. Introduction: Connect the Signal I/O box to the DVR. The signal I/O box has RS485 ports for PTZ camera control. 2. Installation: 2.1 Setting PTZ camera control protocol: Follow PTZ camera user manual to choose and setting control protocol, all the camera need to choose same protocol type. 2.2 Setting PTZ camera ID: Follow PTZ camera user manual to set PTZ ID, each camera has a unique ID it’s own.
4. PTZ control: How to move PTZ camera? The process is as follows: 1. Press PTZ button. 2. Select Channel to control. 3. Press Up key to move camera up. 4. Press Down key to move camera down. 5. Press Left key to move camera left. 6. Press Right key to move camera right. 7. At any time press Stop key to stop camera move. 8. Press Auto key to turn the auto pan on. 9. Press PTZ key to quit PTZ control mode.
PC PLAYER SOFTWARE OPERATION 1. Install PC player software. 2. Control panel and function.
Minimize / Exit Watermark Protection: The system will show the warning light and stop playing when the recorded data is abnormally put in or removed. Press “Play” button to continue the playback.
3. How to play the file (1) Open the recorded file. (2) Select the file location. (3) Select the file.
(4) Press “Search” button to select recorded data stored on the disk and then press “Open” button. (5) Press “Play” button to start playback. (6) Press “JPEG” button to save single image in JPEG file. (If the image is 16 splits, it will save 16 splits. You can use mouse to select specific channel and then save it).
(7) Press “AVI” button to start transfer function. Select start time & end time, select transferred channel and transferred quality and saving access. Press “Confirm” button to start. (8) The bar will show progress when the system is transferring the file. (9) Play the transferred AVI file: After finding the saved file location, double-click the file by mouse to activate “Media Player” for playback.
(10) Play. (11) Adjust Audio Channel 1 or Channel 2.
