User manual

ManualsBrandsRecoda ManualsComputer equipment4CH MINI Mobile DVR

User Manual for Mobile DVR

4CH MINI Mobile DVR USER MANUAL

Ver. 1.1

RECODA

Summary of content (41 pages)

PAGE 1
A User Manual for Mobile DVR D 4CH MINI Mobile DVR USER MANUAL R E C O Ver. 1.
PAGE 2
User Manual for Mobile DVR Contents 1. System Introduction....................................................................................................................................... 4 1.1. Features.............................................................................................................................................. 4 1.2. Appearance ...................................................................................................... 错误！未定义书签。 1.3. Remote Control ..
PAGE 3
User Manual for Mobile DVR 6. Syestem Upgrade User Guideline................................................................................................................ 33 6.1. MU-MINI-RFS.crc（Record File System）Upgrade ..................................................................... 33 6.2. MU-MINI-APP.crc（Application Program）Upgrade ................................................................... 33 6.3. MCU Upgrade ........................................................................
PAGE 4
User Manual for Mobile DVR 1. System Introduction 1.1. Features  H.264 main profile Video compression format; Support 1 to 4 channels video input.  Adopt 10bit video decoder processor to ensure picture quality, and each video channel is attached with an independent video decoder to avoid disturbing from each other.  Industrial grade design: all electronic components conform to industrial standard through the entire design, including the special connectors dedicated for mobile DVR.
PAGE 5
User Manual for Mobile DVR 1.1.1. 1.2.
PAGE 6
User Manual for Mobile DVR R E C O D A 1.
PAGE 7
User Manual for Mobile DVR 1.4 Front panel C O D The front panel for the device which supports one SD card: A The front panel for the device which supports two SD card: 1.4.1 LED indicators: 【PWR】Power indicator.  【ERR】Error indicator: LED on－No SD cards  【CH1－CH4】Video input indicators  【CH1】LED blinks indicating that the system firmware is being upgraded.
PAGE 8
User Manual for Mobile DVR 1.5 Back panel 【PWR】Power Supply connector  【GPS】GPS antenna connector  【WIRELESS】WIRELESS antenna connector  【USB】USB1.1 port  【ETHERNET】LAN port.  【ALARM IN/OUT】Alarm input and output connector  【VI/VO AI/AO】Audio and video input and output connector E C O D A  R Remark: GPS and wireless transmission functions are available with M603B.
PAGE 9
User Manual for Mobile DVR Specifications Function Item Description Channel 1-4 channels Support CIF、HD1、D1 resolution, compatible with 2CH of D1 & 2CH of CIF. fps: Resolution Recording System 1 to 25f/s/ch adjustable (PAL) or 30f/s/ch (NTSC) . Video Quality 1-4 levels, 1 is the highest level and 4 is the lowest level. OSD Overlays information such as date time and vehicle ID Support two SD card recycle recording.
PAGE 10
User Manual for Mobile DVR Technique Parameters Description Processor Hisilicon Hi3511 Operating system Linux(2.6) Signal format PAL/NTSC GUI Yes Two level password protections for administrators and Security Video users A System Item Input 4 CVBS, 1.0Vp-p, 75Ω Output 1 CVBS, 1.
PAGE 11
User Manual for Mobile DVR Support two (SDHC) SD card, the max capacity is 32G for Storage capacity each. File system: FAT32 4Ch input output 2Ch output Communication RS-232 Yes Interface RJ45 10M/100M Ethernet GPS Embedded GPS module Optional PC Viewer PC playback software Yes Firmware upgrade Upgrade with SD card Yes Power input DC:+8V ~ +36V Power output +12V@1.5A；+5V@1.5A D Others Operating temperature -25℃ to +70℃ R E C GUI 4.
PAGE 12
User Manual for Mobile DVR Factory Default User Password: 111111 4.5 System Main Interface O D A The main interface will be displayed on the screen when you login successfully, it contains C 4.
PAGE 13
User Manual for Mobile DVR "REC TYPE": press the【Enter】 button to select All or Alarm. The default setting is All. “DISK SELECT ": press the【Enter】 button to select the SD card: The default setting is SD1. "DATE": Default is current day. Press digit keys to reset "START TIME": Press digit keys to setup the start time, default setting is 00:00. "END TIME": Press digit keys to setup the end time, default setting is 23:59. "SEARCH": Take curser move to "SEARCH" and press the【Enter】 key to see the result.
PAGE 14
User Manual for Mobile DVR 4.7.2 Basic Settings BASIC SETUP Three type：Y/M/D, D/M/Y, M/D/Y DATE TYPE：Y/M/D TIMEZONE：GMT +08（00~+12 / -01~-12 ） DATE：2009-05-27 09：01：30 IDLE TIME： 30（s）（Default 30 senconds） DEVICE NO ：11111 (Default 30 senconds） COMPANY NAME：Company Name VEHICLE NO：00000 BUS LINE NO：Line number D SAVE A DRIVER NAME：Driver Name “DATE TYPE”: year/month/day, day/month/year or month/day/year. Press 【ENTER】 to select.
PAGE 15
User Manual for Mobile DVR 4.7.
PAGE 16
User Manual for Mobile DVR RECORD TIME LIST DATE TIME 1 EVERYDAY MONDAY 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 TUESDAY WEDNESDAY THURSDAY FRIDAY SATURDAY SUNDAY 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 00:00-00:00 A D SAVE TIME 2 O Note: System will auto start recording within the period in “Timed” setup. 4.7.4 Sub-Stream Settings C Press the【ENTER】key to enter below setting interface.
PAGE 17
User Manual for Mobile DVR Default is 10f, press【ENTER】 key to enter. Click ’SAVE’ to save the configuration. 4.7.5 Power Management POWER SETUP POWER MODE： DELAY POWER OFF： TIME /ACC ON/OFF 5（MIN） HH:MM:SS POWER OFF TIME： HH:MM:SS O D SAVE A DELAY TIME： POWER ON TIME： "Power mode": start up and shut down mode by pressing 【ENTER】 key to select. TIME: DVR will auto power on/off according to the preset time table.  ACC: System will auto power on/off according to vehicle acc switch on/off signal.
PAGE 18
User Manual for Mobile DVR 4.7.6 Alarm Settings ALARM SETUP INPUT PWL RECORD ALARM ON HIGH ON LEFT ON HIGH OFF RIGHT ON LOW ON BRAKE OFF LOW OFF OUTPUT ENABLE PWL ON HIGH OUTPUT2 OFF LOW "ENABLE": switch on/off. G-SENSOR O Alarm input Support 4ch alarm input. SPEED D MOVE DETECT A OUTPUT1 SAVE  ENABLE ON---Enable alarm input; C OFF---Disable alarm input. Press the 【ENTER】 key to select on or off to enable or disable alarm input.
PAGE 19
User Manual for Mobile DVR MOTION DETECTION CHANNEL LEVEL ENABLE CHI/CH2/CH3/CH4 HIGH/MID/LOW OFF/ON AREA SETUP SPEED D  A SAVE  O OVER SPEED SAVE R E C THRESHOLD：0（0~60）（km/h） ENABLE： ENABLE：ON/OFF  G-SENSOR（This functions is available with M603B） G-SENSOR setup, Press the 【ENTER】 key to enter below setting interface for G-sensor configuration: 19
PAGE 20
User Manual for Mobile DVR G-SENSOR REAL LIMIT VALUES X= -0.00 Y= -0.00 Z= -0.00 ADJUST THRESHOLD VALUES ALARM: CLOSE/OPEN X: 2.00g Y: 2.00g Z: 2.00g A SAVE D “LIMIT”: Limit value for X/Y/Z, Minimum value is 0.00g and Maximum value is 9.99g, press digit keys to setup. “ALARM”: G-Sensor alarm OPEN/CLOSE setup, press 【ENTER】to set it.
PAGE 21
User Manual for Mobile DVR Password setting: "PASSWORD": ON---Enable password; OFF---Disable password, press the【ENTER】 key to select. Select and press “SAVE” to save the configuration. 4.7.8 Network Settings: Network parameters should be set on the device. The system will detect devices without any further setting if the configuration is correct . NETWORK SETUP A LOCAL SETUP D IP ADDRESS: 192. 168. 000. 192 NETMASK：255. 255. 255. 000 GATEWAY: 192. 168. 000.
PAGE 22
User Manual for Mobile DVR 3G SETUP 3G： ON / OFF TYPE： WCDMA / EVDO / TD APN： CENTER NO： USER NAME： 3gnet *99# card PASSWORD： card A SAVE D “WIRLESS”: ON—enable wireless; OFF—Disable wireless, press the【ENTER】 key to select. “TYPE”: WCDMA—WCDMA module; EVDO—EVDO module, TD-TD module press the【ENTER】 key to select. O “APN”: APN CMWAP, Press the【Enter】 key to enable the keyboard window, then use left/right/up/down/ enter key to setup.
PAGE 23
User Manual for Mobile DVR DDNS SETUP DDNS： ON / OFF TYPE： DYNDNS / 3322 USER NAME： PASSWORD： DOMIAN： A SAVE D DDNS: Close / Open, with 【Enter】 key to select. "User Name", "Password": user name and password for setting DDNS, press 【Enter】 key to enter, then go to the keyboard interface, move the cursor and input corresponding letter through press 【Enter】 key.
PAGE 24
User Manual for Mobile DVR 4.8 System Info SYSTEM INFO FIRMWARE VER：Mini001.00 HARDWARE VER：V0001 MCU VER：V0001 SD CAPACITY REMAINING SD1 3.6842GB 407.6875MB SD2 0KB "FIRMWARE VER": Software version number. A TOTAL 0KB D SD NO. O "HARDWARE VER": Hardware version number. "MCU VER": Single-chip version number. "SD NUM": Name of SD card. "Remaining ": C "TOTAL ": the total capacity of SD card. The remaining space of SD cards E 4.
PAGE 25
User Manual for Mobile DVR MANAGE TOOL DISK MANAGE DEFAULT SET CFG MANAGE PTZ MANAGE OSD SET 4.9.
PAGE 26
User Manual for Mobile DVR 4.9.3 SD Card Management DISK MANAGE SD FORMAT SD SELECT：SD1/SD2 FORMAT CANCEL D A The data will lost against ’ FORMAT ’, otherwise please press ’ CANCEL’ 。 Disk management is used to format the SD cards. O "SD SELECT": to select SD1 or SD2 by pressing the ‘enter’ key. "CANCEL": Cancel disk management operations, and return back to the management tool interface.
PAGE 27
User Manual for Mobile DVR 4.9.4 Default Settings Warning: Default all settings? No D A Yes O "Yes": Press the【ENTER】key to recover all parameters to the original default settings. "No": Cancel this operation and return back to the management tool interface. C 4.9.5 Config Management Import and export config file R E CONFIG MANAGE  IMPORT CONFIG FILE: IMPORT CFG  EXPORT CURRENT CONFIG FILE: EXPORT CFG NOTICE: CONFIG FILE NAME: DVR.CFG Import Configuration: Import the “DVR.
PAGE 28
User Manual for Mobile DVR 4.9.6 PZT Management PTZ MANAGE CHANNEL ADDRESS BAUDRATE CH1 1（0 ~ 255） 255） 4800/9600/19200/38400/57600/115200 CH2 1（0 ~ 255） 255） 4800/9600/19200/38400/57600/115200 CH3 1（0 ~ 255） 255） 4800/9600/19200/38400/57600/115200 CH4 1（0 ~ 255） 255） 4800/9600/19200/38400/57600/115200 D A SAVE O OSD SETUP REAL TIME DISPLAY TIME: YES \NO C RECORD OVERLAY DISPLAY TIME: YES\ YES\NO GPS: YES\ YES\NO SAVE R E VEHICLE NO: YES\ YES\NO 5 Device Installation 5.
PAGE 29
User Manual for Mobile DVR Notes: 1: Please make sure the battery voltage range within 12-24V, otherwise device will break down when voltage more than 24V A 2: Please check out the three cables and make sure isolative between them after complete connection 3: Make sure connect the Black and Red cables with battery directly and never choose ground strap connection D way as GND, otherwise device cannot work normally 4: The yellow cable must be connected to the ignition; otherwise device will not support
PAGE 30
D A User Manual for Mobile DVR Connector Name Video Input VIN1~VIN4 Video Output VOUT 1 VOUT BNC connector Audio Input AIN1~AIN2 2 AIN BNC connector AOUT1~AOUT2 2 AOUT PCA connector C O 4 VIN BNC connector E Audio Output Instruction MIC IN 1 MIC IN RCA connector R MIC Input 5.1.
PAGE 31
R E C O D A User Manual for Mobile DVR 5.2. Main Board Outside View 5.2.1.
PAGE 32
User Manual for Mobile DVR VI/VO AI/AO cable connector O 5.2.2.
PAGE 33
User Manual for Mobile DVR 6 Syestem Upgrade User Guideline 6.4 MU-MINI-RFS.crc（Record File System）Upgrade 1. Cope files into SD card. Make sure files were copied totally 2. Insert SD card into device before power on 3. Power on the device and all indicator except SD1 and SD2 will be light. 4. “LOADING” and “ERASING FLASH”showed on window, mainwhile PWR light one and CH1 indicator on front pannel flicking, it means upgrading. A 5. Progress bar will be showed on the window (1%--100%).
PAGE 34
User Manual for Mobile DVR 7 3G User Guideline 7.4 Working principle representation A External Module O D G Sensor,GPS C WCDMA 3G/EVDO HSPA Remote Control Wireless network E 7.
PAGE 35
User Manual for Mobile DVR 7.6 Parameter Settings 7.6.2 Network Setting NETWORK SETUP LOCAL SETUP IP ADDRESS: 192. 168. 000. 192 NETMASK：255. 255. 255. 000 GATEWAY: 192. 168. 000. 001 MAC：00：44：53：75：55：56 CENTER SET D A TYPE：IP/DOMAIN DOMAIN：www.123.cn SERVER IP：192 . 168 . 001 . 000 CONTROL PORT：5678 MEDIA PORT： 5678 SAVE 3G DDNS WIFI 1） Server IP must be globe IP C 2） Default Port is 5678.
PAGE 36
A User Manual for Mobile DVR 7.6.3 D Picture 3 Wireless setting O There are 3 types: WCDMA, EVDO and TD. When user set it, please make sure the type you select must be match with the type of 3G modules (Please R E C make a reference in picture 3) 3G SETUP 3G： ON / OFF TYPE： WCDMA / EVDO / TD APN： CENTER NO： USER NAME： 3gnet *99# card PASSWORD： card SAVE Picture 4 7.6.4 Statues check out 7) Press F1 key on remote control under preview interface to check out current statues.
PAGE 37
User Manual for Mobile DVR (Please make a reference in picture 4) 7.7 PC software setting Make Fclient software running first. When device dial-up successfully, it will connect with sever setted by user automatically. Green color means connecting success (Please make a reference in picture 5) R E C O D A Remote ID 8 Picture 5 F.A.Q 8.4 Wireless Module 1) Q: How to setup network after choose the wireless module? A: Please make a reference on eighteenth page in User Manual.
PAGE 38
User Manual for Mobile DVR and the other possibility is antenna not connect well. 3) Q: Why 3G can not transmit data? A: Probably of the reason is as follows: 1) Didn’t connect 3G antenna 2) Didn’t insert SIM card; 3) Wireless and network setup in a wrong way 4) The PC setup not matches with 3G. For example, the gateway router have not port mapping. 5) Have never turn on PC play back tool.
PAGE 39
User Manual for Mobile DVR 1) Electric voltage isn’t within the range of 8-36 V; 2) The fuse in power cable was burned; 3) ACC setting failure or ignition connects in a wrong way Problem 2: ERR indicator keep on light. The following errors will cause the ERR indicator keep on light. 1) Two SD cards didn't be inserted.
PAGE 40
User Manual for Mobile DVR 3) If the camera takes an electricity power from the equipments directly, may be the equipment’s electric voltage isn't enough to make camera work as usual; 4) The cable that links this channel has problem Problem 6: Record files have no audio Probably of the reason is as follows: 1) Audio function setup in “OFF” mode in system 2) Use wrong input cables Audio input including two types. One is LINE IN and the other one is MIC IN.
PAGE 41
User Manual for Mobile DVR 2) System setting in a wrong way Remarks: More information and user guidelines please find on page fifteenth in user manual Problem 10: GPS signal lost GPS has no signal, probably of the reason is as follows: 1) Didn’t connect GPS antenna; 2) The GPS antenna put indoors; 3) The GPS module damages; 4) The software of device M603A nonsupport this function; Problem 11: G-Sensor data abnormal.