Instruction Manual
Table Of Contents
- CONTENTS
- INTRODUCTION
- SAFETY MEASURES
- PANEL HANDLING
- CHOOSING AN INSTALLATION LOCATION
- ELECTRICAL INSTALLATION
- MECHANICAL INSTALLATION
- PANEL INSTALLATION
- Securing of Panels
- Installation of REC TwinPeak 4 Series panels
- Installation of REC TwinPeak 5 Series panels
- Installation of REC N-Peak 2 Series panels
- Installation of REC N-Peak 3 Black Series panels
- Mounting methods: Slide in systems
- Mounting methods: Mounting holes
- Mounting methods: Six-point mounting
- Drainage holes
- CONNECTIONS AND CONNECTORS
- CABLE MANAGEMENT
- PANEL MAINTENANCE
- RECYCLING
- DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT
- PANEL CHARACTERISTICS
- ANNEX 1: INSTALLATIONS ON WATER PLATFORMS
- ANNEX 2: INSTALLATIONS USING MODULE LEVEL POWER ELECTRONICS
- EC DECLARATION OF CONFORMITY
- UKCA DECLARATION OF CONFORMITY
- DOCUMENT HISTORY
- Fig. 1: Clamp specifications
- Fig. 2: Panel quarter divisions
- Fig. 3: Clamping of REC TwinPeak 4 Series panels with rails parallel to short side of the panel
- Fig. 4: Clamping of REC TwinPeak 4 Series panels with rails parallel to long side of the panel
- Fig. 5: Clamping of REC TwinPeak 4 Series panels using short rails
- Fig. 6: Clamping of REC TwinPeak 5 Series panels with rails parallel to short side of the panel
- Fig. 7: Clamping of REC TwinPeak 5 Series panels with rails parallel to long side of the panel
- Fig. 8: Clamping of REC TwinPeak 4 Series panels using short rails
- Fig. 9: Clamping of REC N-Peak 2 Series panels with rails parallel to short side of the panel
- Fig. 10: Clamping of REC N-Peak 2 Series panels with rails parallel to long side of the panel
- Fig. 11: Clamping of REC N-Peak 2 Series panels using short rails
- Fig. 12: Clamping of REC N-Peak 3 Black Series panels with rails parallel to short side of the panel
- Fig. 13: Clamping of REC N-Peak 3 Black Series panels with rails parallel to long side of the panel
- Fig. 14: Clamping of REC N-Peak 3 Black Series panels using short rails
- Fig.15: Mounting holes
- Fig. 16: Device specifications for mounting holes
- Fig. 17: Mounting hole installation example
- Fig. 18: Six-point mounting configuration clamping zones
- Fig. 19: Drainage and grounding holes
- Fig. 20: Minimum cable bend radius
- Fig. 21: WEEE symbol
- Fig. 22: Panel dimensions: REC TwinPeak4 Series
- Fig. 23: Panel dimensions: REC TwinPeak 4 Black Series
- Fig. 24: Panel dimensions: REC TwinPeak 5 Series
- Fig. 25: Panel dimensions: REC TwinPeak 5 Black Series
- Fig. 26: Panel dimensions: REC N-Peak 2 Series
- Fig. 28: Panel dimensions: REC N-Peak 3 Black Series
- Fig. 29: MLPE device installation zones
REC Installation Manual - REC Solar Panels - IEC /
Rev N . Ref: PMIM
Fig. : Clamping of REC TwinPeak Series panels with rails parallel to long side of the panel
MOUNTING REC TWINPEAK SERIES PANELS WITH CONTINOUS RAILS PARALLEL TO LONG SIDE OF THE PANEL
A continous rail (or other support structure) spans the complete underside of the panel.
250 mm [9.8 in]
100 mm [3.9 in]
0
0
250 mm [9.8 in]
100 mm [3.9 in]
0
750 mm [29.5 in]
250 mm [9.8 in]
100 mm [3.9 in]
0
0
250 mm [9.8 in]
100 mm [3.9 in]
0
750 mm [29.5 in]
CAUTION
The center point of each clamp and the minimum grip length must be fully located in the same clamping zones to be rated to that load (fig. ).
If the panel is secured in zones with different load values, it is rated to the lowest load value only.
Rail position
Rail position
Legend
Clearance Gap
Clamping zone
mm mm > mm
Test Load
(Design Load)
Test Load
(Design Load)
Test Load
(Design Load)
Long Side
Mounting
mm
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
Short Side
Mounting
mm X
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa *
(+ Pa / Pa)
mm X
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
Once a module is secured in each of the zones (fig. ), additional clamps, i.e., ≥, may be freely located on panel frame without
affecting the warranty. Loads marked with a * were not certified as part of IEC / testing; these have been evaluated by
REC’s internal testing process.