Panel Install Manual
Table Of Contents
- Fig. 5: Clamping of REC Alpha Series panels using a short support
- Fig. 6: Clamping of REC Alpha 72 Series panels with support parallel to short side of the module
- Fig. 7: Clamping of REC Alpha 72 Series panels using a short support
- Fig. 8: Mounting holes: REC Alpha Series
- Fig. 9: Mounting holes: REC Alpha 72 Series
- Fig. 10: Device specifications for mounting holes
- Fig. 11: Mounting hole installation example
- Fig. 12: Drainage and grounding holes
- Fig. 13: Grounding lug dimensions and fastening torque
- Fig. 14: Connector mating matrix
- Fig. 15: Minimum cable bend radius
- Fig. 17: Panel dimensions: REC Alpha Black Series
- Fig. 18: Panel dimensions: REC Alpha 72 Series
- Fig. 19: REC Alpha Series MLPE device installation zones
- Fig. 20: REC Alpha 72 Series MLPE device installation zones
- Irradiance (W/m²)
- Irradiance (W/m²)
- module
- module
- module
- Rel. Efficiency (%)
- Rel. Efficiency (%)
- Support length under
- Support length under
- Support length under
- Support position
- Support position
- INTRODUCTION
- SAFETY MEASURES
- PANEL HANDLING
- CHOOSING AN INSTALLATION LOCATION
- ELECTRICAL INSTALLATION
- MECHANICAL INSTALLATION
- PANEL INSTALLATION
- CONNECTIONS AND CONNECTORS
- CABLE MANAGEMENT
- PANEL MAINTENANCE
- RECYCLING
- DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT
- PANEL CHARACTERISTICS
- ANNEX 1: INSTALLATIONS ON WATER PLATFORMS
- ANNEX 2: INSTALLATIONS USING MODULE LEVEL POWER ELECTRONICS
- DOCUMENT HISTORY
- Fig. 1: Clamp specifications
- Fig. 2: Panel quarter divisions
- Fig. 3: Clamping of REC TwinPeak 4 Series panels with rails parallel to short side of the panel
- Fig. 4: Clamping of REC TwinPeak 4 Series panels with rails parallel to long side of the panel
- Fig. 5: Clamping of REC TwinPeak 4 Series panels using a short support
- Fig. 6: Clamping of N-Peak panels on rails parallel to short side of module
- Fig. 7: Clamping of N-Peak panels on rails parallel to long side of module
- Fig. 8: Clamping of REC N-Peak Series panels using short rails
- Fig. 9: Clamping of REC N-Peak 2 Series panels with rails parallel to short side of the panel
- Fig. 10: Clamping of REC N-Peak 2 Series panels with rails parallel to long side of the panel
- Fig. 11: Clamping of REC N-Peak 2 Series panels using a short support
- Fig. 12: Mounting holes: REC 60-cell panels
- Fig. 13: Mounting holes: REC 72-cell panels
- Fig. 14: Device specifications for mounting holes
- Fig. 15: Mounting hole installation example
- Fig. 16: Drainage and grounding holes
- Fig. 17: Grounding lug dimensions and fastening torque
- Fig. 18: Connector mating matrix
- Fig. 19: Minimum cable bend radius
- Fig. 20: Panel dimensions: REC TwinPeak 4 Series
- Fig. 21: Panel dimensions: REC TwinPeak4 Black Series
- Fig. 22: Panel dimensions: REC N-Peak Series
- Fig. 23: Panel dimensions: REC N-Peak Black Series
- Fig. 24: Panel dimensions: REC N-Peak 2 Series
- Fig. 25: Panel dimensions: REC N-Peak 2 Black Series
- Fig. 26: REC 60-cell panels MLPE device installation zones
- Fig. 27: REC 72-cell panels MLPE device installation zones
REC Installation Manual - REC Panels - UL 6
Rev L . Ref: PMIM
INTRODUCTION
Thank you for choosing REC photovoltaic panels for your installation. REC solar panels are ideal for delivering long-lasting and reliable power output.
They have been created through intelligent design and are manufactured to the highest quality and environmental standards. With correct installation
and maintenance, REC panels will provide decades of clean and renewable energy.
Please read this entire manual carefully. It contains critical information on safety, as well as detailed instructions for the installation, operation and
maintenance of the panels. Failure to follow these procedures will invalidate the warranty (www.recgroup.com/warranty). Review all instructions and
safety notes in this manual before working on the system. Failure to do so may lead to injury or damage to property.
HOW TO USE THIS MANUAL
This manual describes the procedures for the terrestrial installation of all REC solar panels certified according to IEC & UL standards.
This includes all product variants (indicated by the appropriate suffix in the panel name) e.g., a white or black backsheet. The installed panel is considered
to be in compliance with IEC & UL only when mounted in the manner specified by this installation manual. Note that any panel without
a frame (laminate) is not considered to comply with the requirements of IEC & UL unless mechanically installed with hardware that has
been tested and evaluated with the panel under this standard or by a field inspection certifying that the installed panel complies with the requirements
of IEC & UL .
Except where specifically stated, the information and drawings in this manual refer to all frame, backsheet, and cell types; the illustrations are only a
generic representation of the instructions regardless of color or exact design. Throughout the manual, you will see sections which highlight important
information or notes:
YOUR RESPONSIBILITY AS AN INSTALLER
Installers are responsible for the safe and effective installation and operation of the system and for adhering to all applicable local standards and
regulations. Prior to installation installers must check all current regulations and permits concerning solar installations and ensure all local directives
are observed. Furthermore, installers are responsible for the following:
• Only qualified personnel must perform work on photovoltaic systems such as installation, commissioning, maintenance and repairs
• Be sure to follow the safety instructions for all system components
• Ensuring the REC panels are in a suitable condition for use and appropriate for the particular installation and environment
• Using only parts that comply with the specifications set out in this manual
• Ensuring a safe installation of all aspects of the electrical array
• All tools and equipment should be properly maintained and inspected prior to use
As this manual may contain instructions for different product variants, ensure you follow the instructions for the correct product where specified.
SUPPORT
Do not aempt to install REC solar panels if you are unsure of the procedure or suitability. For further support, questions or guidance with your
installation, please call your distributor or contact your REC sales office, which can be found at: www.recgroup.com/contacts.
LIABILITY DISCLAIMER
REC SOLAR PTE. LTD. accepts no liability for the usability and functionality of its photovoltaic panels if the instructions in this guide are not observed.
Since compliance with this guide and the conditions and methods of installation, operation, use and maintenance of the panels are not checked or
monitored by REC SOLAR PTE. LTD., REC SOLAR PTE. LTD. accepts no liability for damage arising from improper application or incorrect installation,
operation or maintenance. This does not apply to damages due to a panel fault, in cases of loss of life, bodily injury or damage to health or in the event
of a grossly negligent breach of obligations on the part of REC SOLAR PTE. LTD. and/or in the event of an intentional or grossly negligent breach of
obligations by a legal representative or vicarious agent. REC reserves the right to make changes or amendments to this manual at any time, without
prior notice.
This document may be produced in different languages. If there is any conflict, the English language version shall be definitive.
LIMITED WARRANTY
The REC Limited Warranty is available to download from www.recgroup.com/warranty. Ignoring any of the instructions in this manual may be classed
as improper installation or use and invalidate the Warranty Terms and Conditions. If you have any questions about installation and the Warranty validity,
please contact REC.
NOTE
Indicates important notes to help with the installation.
i
CAUTION
Indicates potential for damage to the array or property.
DANGER
Indicates potential for damage to personal safety.