Alpha Series Installation
Table Of Contents
- Fig. 5: Clamping of REC Alpha Series panels using a short support
- Fig. 6: Clamping of REC Alpha 72 Series panels with support parallel to short side of the module
- Fig. 7: Clamping of REC Alpha 72 Series panels using a short support
- Fig. 8: Mounting holes: REC Alpha Series
- Fig. 9: Mounting holes: REC Alpha 72 Series
- Fig. 10: Device specifications for mounting holes
- Fig. 11: Mounting hole installation example
- Fig. 12: Drainage and grounding holes
- Fig. 13: Grounding lug dimensions and fastening torque
- Fig. 14: Connector mating matrix
- Fig. 15: Minimum cable bend radius
- Fig. 16: Panel dimensions: REC Alpha Series
- Fig. 17: Panel dimensions: REC Alpha Black Series
- Fig. 18: Panel dimensions: REC Alpha 72 Series
- Fig. 19: REC Alpha Series MLPE device installation zones
- Fig. 20: REC Alpha 72 Series MLPE device installation zones
- Irradiance (W/m²)
- Irradiance (W/m²)
- Irradiance (W/m²)
- module
- module
- module
- Rel. Efficiency (%)
- Rel. Efficiency (%)
- Rel. Efficiency (%)
- Support length under
- Support length under
- Support length under
- Support position
- Support position
- Support position
- Support position
- Support position
- Support position
- INTRODUCTION
- SAFETY MEASURES
- PANEL HANDLING
- CHOOSING AN INSTALLATION LOCATION
- ELECTRICAL INSTALLATION
- MECHANICAL INSTALLATION
- PANEL INSTALLATION
- CONNECTIONS AND CONNECTORS
- CABLE MANAGEMENT
- PANEL MAINTENANCE
- RECYCLING
- DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT
- PANEL CHARACTERISTICS
- ANNEX 1: INSTALLATIONS ON WATER PLATFORMS
- ANNEX 2: INSTALLATIONS USING MODULE LEVEL POWER ELECTRONICS
- DOCUMENT HISTORY
- Fig. 1: Clamp specifications
- Fig. 2: Panel quarter divisions
- Fig. 3: Clamping of REC Alpha Series panels with rails parallel to short side of the panel
- Fig. 4: Clamping of REC Alpha Series panels with rails parallel to long side of the panel
- Fig. 5: Clamping of REC Alpha Series panels using a short support
- Fig. 6: Clamping of REC Alpha Pure Series panels with rails parallel to short side of the panel
- Fig. 7: Clamping of REC Alpha Pure Series panels with rails parallel to long side of the panel
- Fig. 8: Clamping of REC Alpha Pure Series panels using short rails
- Fig. 9: Clamping of REC Alpha 72 Series panels with rails parallel to short side of the panel
- Fig. 10: Clamping of REC Alpha 72 Series panels using short rails
- Fig. 11: Mounting holes: REC Alpha Series
- Fig. 12: Mounting holes: REC Alpha 72 Series
- Fig. 13: Device specifications for mounting holes
- Fig. 14: Mounting hole installation example
- Fig. 15: Drainage and grounding holes
- Fig. 16: Grounding lug dimensions and fastening torque
- Fig. 17: Connector mating matrix
- Fig. 18: Minimum cable bend radius
- Fig. 19: Panel dimensions: REC Alpha Series
- Fig. 20: Panel dimensions: REC Alpha Black Series
- Fig. 21: Panel dimensions: REC Alpha Pure Series
- Fig. 22: Panel dimensions: REC Alpha 72 Series
- Fig. 23: REC Alpha Series MLPE device installation zones
- Fig. 24: REC Alpha 72 Series MLPE device installation zones
REC Installation Manual - REC Alpha Panels - UL 6
Rev G . Ref: PMIM
CAUTION
The center point of each clamp and the minimum grip length must be fully located in the same clamping zones to be rated to that load (fig. ).
If the panel is secured in zones with different load values, it is rated to the lowest load value only.
Rail positioning
Rail positioning
Fig. : Clamping of REC Alpha Pure Series panels with rails parallel to short side of the panel
375 mm [14.8 in]
700 mm [27.5 in]
505 mm [15.9 in]
300 mm [11.8 in]
200 mm [7.9 in]
0
255 mm [10.0 in]
0
300 mm [11.8 in]
200 mm [7.9 in]
0
300 mm [11.8 in]
200 mm [7.9 in]
0
300 mm [11.8 in]
200 mm [7.9 in]
0
610 mm [24.0 in]
375 mm [14.8 in]
700 mm [27.5 in]
505 mm [15.9 in]
0
255 mm [10.0 in]
610 mm [24.0 in]
Legend
Clearance Gap
Clamping zone
mm mm > mm < mm
Test Load
(Design Load)
Test Load
(Design Load)
Test Load
(Design Load)
Test Load
(Design Load)
. in
mm)
X
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
X
. . in
mm)
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
X
. . in
mm)
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
X
. . in
mm)
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
X
. . in
mm)
+ Pa / Pa
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
X
. in
mm)
X
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa *
(+ Pa / Pa)
X
. . in
mm)
X
+ Pa / Pa *
(+ Pa / Pa)
+ Pa / Pa
(+ Pa / Pa)
X
Once a module is secured in each of the zones (fig. ), additional clamps, i.e., ≥, may be freely located on panel frame without affecting
the warranty. Loads marked with a * were not certified as part of IEC / testing; these have been evaluated by REC’s internal
testing process.
Long Side Mounting
Short Side
Mounting
Rail position
Rail position
INSTALLATION OF REC ALPHA PURE SERIES PANELS
MOUNTING REC ALPHA PURE SERIES PANELS WITH CONTINOUS RAILS PARALLEL TO SHORT SIDE OF THE PANEL
A continous rail (or other support structure) spans the complete underside of the panel.