ASSEMBLY INSTRUCTIONS SINGLE DOOR FLOOR CABINET WHITE ESPRESSO ADULT ASSEMBLY REQUIRED This product requires assembly by an adult because of the small parts. Care should be taken in unpacking and assembling this item to keep the small parts away from children. WARNING Young children can be seriously injured or killed, if furniture tips over. Don’t use this item for a TV stand. Use angle-braces or anchors to secure furniture to the wall.
THIS SHELF UNIT WILL HOLD UP TO 25 POUNDS PER SHELF OR A TOTAL OF 75 POUNDS. DO NOT LOAD EACH SHELF WITH MORE THAN 25 POUNDS. IF LOADED WITH MORE THAN 25 POUNDS PER SHELF AS THIS MAY CAUSE DAMAGE TO THE SHELF AND MAY CAUSE SERIOUS INJURY OR DEATH.
PARTS LIST
STEP 1 STEP 1 1. Screw 4 cam bolts (A) into the pre-threaded holes on the top board (1) by using a Philips screwdriver. 2. Insert 6 wood dowels (C) into the dowel holes on the top board (1). STEP 2 STEP 2 1. Screw 4 cam bolts (A) into the pre-threaded holes on the left side panel (2) by using a Philips screwdriver. 2. Insert 8 wood dowels (C) into the dowel holes on the left side panel (2). 3. Attach the magnet (H) to the left side panel (2). 4.
STEP 3 STEP 3 1. Screw 4 cam bolts (A) into the pre-threaded holes on the right side panel (3) by using a Philips screwdriver. 2. Insert 8 wood dowels (C) into the dowel holes on the right side panel (3). STEP 4 STEP 4 1. Insert 1 screw (K) through the hole on the magnet plate (J) then tighten to the door (5) by using a Philips screwdriver, 2. Attach knob (D) to the door (5), insert 1 screw (E) through hole on the door (5) then tighten to knob (D) by using a Philips screwdriver. 3.
STEP 5 STEP 5 1. Attach the cross bar (4), middle panel (6), bottom board (7) and rear cross bar (10) to the left side panel (2) by inserting cam bolts into cam lock holes and inserting wood dowels into dowel holes on the cross bar (4), middle panel (6), bottom board (7) and rear cross bar (10). 2. Insert 4 cam locks (B) into cam lock holes on the middle panel (6) and bottom board (7) separately then rotate clockwise to secure cam bolts in place by using a Philips screwdiver. STEP 6 STEP 6 1.
STEP 7 STEP 7 1. Insert 4 wood dowels (C) into dowel holes on the cross bar (4) and rear cross bar (10). 2. Attach the door (5) to the middle panel (6) and bottom board (7) by inserting door pins (G) into the holes on the middle panel (6) and bottom board (7). STEP 8 STEP 8 1.
STEP 9 STEP 9 1. Attach the top board (1) to the pre-assembled both side panel (2),(3) ,cross car (4) and rear cross bar (10) by inserting cam bolts into cam lock holes and inserting wood dowels into dowel holes on the both side panel (2),(3) ,cross car (4) and rear cross bar (10). 2. Insert 4 cam locks (B) into cam lock holes on the both side panel (2),(3) separately then rotate clockwise to secure cam bolts in place by using a Philips screwdiver. STEP 10 STEP 10 1.
ENJOY YOUR NEW CABINET NOW ! Attention Adults: The cabinet should be checked periodically for damage or loose screws/parts. Take appropriate action necessary to correct the hazard such as tightening of screws and taking any damaged parts away from the children.
