Operation Manual

www.rebox.tv
38
• Connection Settings: You can set the connection settings to your personal preferences. Check your TV
and VCR user manuals for the correct settings. You can change your Connection settings by applying the
following steps:
1. Select “Connection” and press OK or the Right button (Figure 19)
• TV Mode: Press OK or the Right button and set your TV mode to “Multi”, “PAL” or “NTSC”.
• Video Output: Press OK or the Right button and set your Video mode to “CVBS” (Composite
video) or “RGB” (preferred option if your TV set is compatible with it).
• TV mode: Press OK or the Right button and set your screen mode to “4 : 3” , “4 : 3 Letterbox”, or
“16 : 9” format. This depends on the format of your TV.
• Audio Output : Press OK or the Right button and set your audio output to “Stereo”, “Left” or “Right”
(left or Right is for mono TV sets)
• S/PDIF Output: Press OK or the Right button and activate your S/PDIF output on the back of your
receiver, so you can connect it to a digital Audio amplifier using an coaxial cable. If you have
connected your digital amplifier, set the SPDIF output to: “Enabled”.
• VCR Output: Press OK or the Right button and set the scart output to “Automatic” or “Terminal”. If
set to “Terminal”, the VCR scart signal is not automatically looped through.
• RF modulator: Press OK or the Right button and set the UHF mode to “PAL B/G”, “PAL I” or “PAL
D/K”. If the TV set is connected using a coaxial (RF) cable, you must select RF modulator type
here. The RF modulator type affects the channel audio. (Select PAL I for UK , Pal B/G for use in
Central Europe).
• RF Channel: Press OK or the Right button and set the UHF channel number to the same UHF
channel number of your TV set. This only has to be done if your TV set is connected with a coaxial
(RF) Cable. If the UHF Channel numbers of the receiver and the TV set are not set the same, no
picture will be displayed.
2. Press BACK until you go back to main menu.
Menu Settings: You can set the OSD (On Screen Display) to your personal preferences. You can change the OSD
settings by applying the following steps:
1. Select “Menu Settings” and press OK or the Right button.
• Color Scheme: Press OK or the Right button and set the colours of the OSD menu to
“Standard”, “Color 1” or “Color 2”.
• Transparency: Press OK or the Right button and select how transparent you want
your OSD.
• Brightness: Press OK or the Right button and select how you want the OSD to be.
• Duration: Press OK or the Right button and select how long you want the information
banner to be on the screen when starting up your receiver or when changing
channels.
2. Press BACK until you go back to main menu.
• Time setting: The system uses GMT (Greenwich Mean Time) as a default. To set the time, apply the
following steps:
1. Select “Time Settings” and press OK or the Right button.
• Select Time Zone: Press OK or the Right button, and a list of the GMT plus or minus the hours
you need for your country is displayed. Using UP/DOWN keys select the correct one, and the
receiver will automatically show the current time in your country.
To set the time manually:
• Select GMT usage: Press OK or the Right button and use the UP/DOWN buttons to set the GMT
usage to “off”. Press OK to save your setting. The time setting menu will now activate the bottom
two fields of the menu.
• Adjust Time: Use your Numeric buttons [0-9] to set the local time. Once set, press OK to save the
time.
• Select Set Date: Press OK or the Right button and set the date the way you have set the time.
Note: We advise you to use the GMT time settings, if you use the manual time settings, the time will be lost after the
unit has been disconnected from the mainpower.
2. Press the BACK button until you go back to the Main Menu.