WSS530 VoIP Phone Advanced Business Phone For IPPBX applications User Manual Version: V1.7.90.72 © 2009 Realtone technology Co,. Ltd All rights reserved. This document is supplied by Realtone Technology Co.
Safety Notices Please read the following safety notices before installing or using this phone. They are crucial for the safe and reliable operation of the device. l Please use the external power supply that is included in the package. Other power supplies may cause damage to the phone, affect the behavior or induce noise. l Before using the external power supply in the package, please check with home power voltage. Inaccurate power voltage may cause fire and damage.
Table of Content 1.INTRODUCING WSS530 VOIP PHONE .................................................................................... 5 1.1. THANK YOU FOR YOUR PURCHASING WSS530 ........................................................................ 5 1.2. DELIVERY CONTENT ............................................................................................................... 5 1.3. KEYPAD................................................................................................................
.3.3.1. SIP Config..............................................................................................................................28 4.3.3.2. IAX2 Config...........................................................................................................................32 4.3.3.3. Stun Config ............................................................................................................................33 4.3.3.4. DIAL PEER setting ...........................................
1. Introducing WSS530 VoIP Phone 1.1. Thank you for your purchasing WSS530 Thank you for your purchasing WSS530, WSS530 is a full-feature telephone that provides voice communication over the same data network that your computer uses. This phone functions not only much like a traditional phone, allowing to place and receive calls, and enjoy other features that traditional phone has, but also it own many data services features which you could not expect from a traditional telephone.
Transfer mute for more details). In idle mode, press this key, LCD will show “Do Not Disturb”, and this phone is set to be No disturbing mode. Press this key again to cancel this function. Use the key to realize blind transfer or attended transfer please refers to 3.4.-call transfer for more details). In the idle mode, press this key, LCD will show”call forward”. After this indication disappears, User can configure the forward phone no. of SIP1 or SIP2.
1.4. Port for connecting Port Port name Power switch description Input: 5V AC, 1A WAN 10/100M Connect it to Network LAN 10/100M Connect it to PC Handset Port type: RJ-9 connector Headset Port type: RJ-9 connector Headset Port type: 3.5mm jack WSS530 provide two Ethernet ports and a power adaptor. Also has two headset interfaces with RJ-9 port and 3.5mm jack. Please refer to safety notes of this manual carefully before power adaptor is connected.
2. Initial connecting and Setting 2.1. Connect the phone 2.1.1. Connect to network Step 1: Connect the IP Phone to the corporate IP telephony network. Before you connect the phone to the network, please check if your network can work normally. You can do this in one of two ways, depending on how your workspace is set up. Direct network connection—by this method, you need at least one available Ethernet port in your workspace.
Step 4: push the on/off switch on the back of the phone to the on side, then the phone’s LCD screen displays “Initializing wait logon”. Later, a ready screen typically displays the date, time. If your LCD screen displays different information from the above, you need refer to the next section “Initial setting” to set your network online mode. If your VoIP phone registers into corporate IP telephony Server, your phone is ready to use. 2.1.2.
5. Press Soft2 (Edit) again, then input your PPPoE password and press Soft2 (OK), With “Saved” displayed, screen will display the current password: ******, and confirm: you need input the password again, after confirm, press soft2 (OK) to save the Account and password. 6. Press Soft3 (Quit) once return to “Net Mode”. Press Soft2 (Save) the screen will show “Saved” and then jump to show the current net mode. 7.
2. Press "OK" or Soft2 (Enter) to show “Net Mode”. Select “DHCP”. Press Soft2 (Save), with “saved” shown, screen will jump to show the current net mode. 3. Press or Soft3 (Quit) thrice back to main interface and at this time phone is until the phone shows “DHCP”，If the trying to change to DHCP mode. Press screen shows the IP address and gateway which were set just now, it shows that DHCP mode takes effect.
3. WSS530’s basic operation 3.1. Answer calls WSS530 will ring to indicate you when there is call incoming，below is ways to answer call： l Answer with hook off Take handset, you can talk directly. You can just hang up to finish talk。 l Answer with hands-free Press l to begin talking. Press again to finish talk Answer with headset Press to answer the call, if the phone detect headset LED will turn to green, when you press again the phone change to speaker mode.
getting dialing tone, you could begin to dial number. After finishing it, press # and WSS530 will send the number and call the number. When you hear a ringback tone and screen shows the callee’s number, it shows that the person you called is ringing. If callee answers the call, you can begin to talk and your phone will keep showing callee’s number and counting time. Press again to finish talk. l Using directory Press in stand-by mode, you will access to phonebook.
Note：it is no use to press Soft3(Close) to finish talk, if there is only one current call. 3.4. Call transfer l Blind Transfer During talk, press or Soft2 (Transf), and then dial the number that you want to transfer to, and finished by "#". Phone will transfer the current call to the third party. After finishing transfer, the call you talk to will be hanged up. User can not select SIP line when phone transfers call.
User can press Soft1 (Conf) to dial the line2 (press Soft1 (Answer) to answer the call directly if this call is from line2) during talking with line1. After line2 connect, user can press Soft1 (Switch) to select which line you prefer to transfer, then press transfer and press to input the number you want to again to do the transfer. 3.8. Call records WSS530 supports 100 items of missed call, 100 items of incoming call, and 100 items of dialed call.
4. Web configuration 4.1. Introduction of configuration 4.1.1. Ways to configure WSS530 has three different ways to different users. l l l Use phone keypad. Use web browser（recommendatory way）. Use telnet with CLI command. 4.1.2. Password Configuration There are two levels to access to phone: root level and general level.
4.3. Configuration via WEB 4.3.1. BASIC 4.3.1.1. Status Status Field name Network Phone Number Explanation Shows the configuration information on WAN and LAN port, including the connect mode of WAN port (Static, DHCP, PPPoE), MAC address, the IP address of WAN port and LAN port, ON or OFF of DHCP mode of LAN port. Shows the phone numbers provided by the SIP LINE 1-3 servers and IAX2. The last line shows the version number and issued date. 4.3.1.2.
Please select the proper network mode according to the network condition. WSS530 provide three different network settings: l Static: If your ISP server provides you the static IP address, please select this mode, then finish Static Mode setting. If you don’t know about parameters of Static Mode setting, please ask your ISP for them. l DHCP: In this mode, you will get the information from the DHCP server automatically; need not to input this information artificially.
Display detailed information that you manual config. Choose DHCP MODE，click【NEXT】can config SIP(default SIP1)simply, also can browse too. Click【BACK】can return to the last page. Like Static IP MODE。 Choose PPPoE MODE，click【NEXT】can config the PPPoE account/password and SIP(default SIP1)simply, also can browse too. Click【BACK】can return to the last page. Like Static IP MODE。 PPPoE Server It will be provided by ISP. Username Input your ADSL account. Password Input your ADSL password.
MMI SET Field name Language Set Greeting Message explanation Set the language of phone, English is default. The greeting message will display on lcd when phone is idle. It can support 16 chars. the default chars are VOIP PHONE. 4.3.2. Network 4.3.2.1.
Active IP Current Netmask MAC Address Current Gateway Get MAC Time The current IP address of the phone. The current Netmask address. The current MAC address of the phone. The current Gateway IP address. Shows the time of getting MAC address Please select the proper network mode according to the network condition. WSS530 provide three different network settings: l Static: If your ISP server provides you the static IP address, please select this mode, then finish Static Mode setting.
Password Input your ADSL password. Notice: 1）Click “Apply” button after finished your setting, IP Phone will save the setting automatically and new setting will take effect. 2）If you modify the IP address, the web will not response by the old IP address. Your need input new IP address in the address column to logon in the phone.
In chart 1, there is a layer 2 switch without setting VLAN. Any broadcast frame will be transmitted to the other ports except the send port. For example, a broadcast information is sent out from port 1 then transmitted to port 2,3and 4. In chart 2, red and blue indicate two different VLANs in the switch, and port 1 and port 2 belong to red VLAN, port 3 and port 4 belong to blue VLAN.
QoS Configuration Field name VLAN Enable VLAN ID Check Enable Voice/Data VLAN differentiated DiffServ Enable DiffServ Value Voice 802.1P Priority Data 802.1P Priority Voice VLAN ID Data VLAN ID explanation Before select it to enable VLAN, you need enable Bridge mode in LAN config. Enable VLAN ID check by selecting it. After enable VLAN ID check, if VLAN ID of a data package is not the same with the phone’s or a data package do not have VLAN ID, the data package will be discarded.
4) Startup VLAN, if set Voice/Data VLAN differentiated as data untagged, then the packet of the signal/voice will use the Voice VLAN ID as the tag, but the data packets will not take the VLAN tag. 5) If Disable the VLAN, regardless to set the Voice/Data VLAN differentiated or not, all packets will not take the VLAN tag; If enable the DiffServ, all packets will only take the DiffServ value.
4.3.2.5. DHCP SERVER DHCP SERVER Field name DHCP Leased Table explanation IP-MAC mapping table. If the LAN port of the phone connects to a device, this table will show the IP and MAC address of this device. Shows the DHCP Lease Table， the unit of Lease time is Minute.
Select name of lease table, click the Delete button will delete the selected lease table from DHCP lease table. Select DNS Relay, the default is enabled. Click the Apply button to DNS Relay become effective. Notice: 1）The size of lease table can not be larger than the quantity of C network IP address. We recommend you to use the default lease table and not modify it. 2）If you modifies the DHCP lease table, you need save the configuration and reboot. 4.3.2.6.
Server Time Zone Time Out 12 Hours Systems SNTP Enable Daylight Time shift(minutes) Month Week Day Hour Minute Set SNTP Server IP address. Select the Time zone according to your location. Set the time out, the default is 60 seconds. Switch the time mechanism between 12 hours and 24 hours. Default is 24 hours mode Select the SNTP, and click Apply to make the SNTP Times effective.
SIP Config Field name explanation Choose line to set info about SIP, there are 3 lines to choose. You can switch by 【Load】 button.
Server Name Server Address Server Port Account Name Password Phone Number Display Name Proxy Server Address Proxy Server Port Proxy Username Proxy Password Domain Realm Enable Register Register Expire Time NAT Keep Alive Interval User Agent Signal Key Media Key Local port Ring type Hot line Number Conference Number Transfer Expire Time Enable subscribe Enable Keep Authentication NAT Keep Alive so, show Unapplied; Set the server name. Input your SIP server address. Set your SIP server port.
Enable Via rport Enable PRACK Long Contact Enable URI Convert Dial Without Register Ban Anonymous Call Enable DNS SRV Forward Type Forward Phone Number Server Type DTMF Mode RFC Protocol Edition Transport Protocol RFC Privacy Edition Subscribe Expire Time Enable Conference number MWI Number Click to Talk Signal Encode RTP Encode Enable Session Timer has no packets sending to device in private network to keep NAT alive, user could set this function ON.
Answer With Single Codec Auto TCP Enable Strict Proxy Enable GRUU Enable Display name Quote will refresh the SIP sessions. Enable/Disable the function when call is incoming, phone replies SIP message with just one codec which phone supports. Set to use automatically TCP protocol to guarantee usability of transport as message is above 1300 byte Support the special SIP server-when phone receives the packets sent from server， phone will use the source IP address, not the address in via field.
Echo Test Number Echo Test Text Refresh Time Enable Register Enable G.729 Set echo test number. If IAX2 server supports echo test, and echo test number is non- numeric, system could set an echo test number to replace the echo test text. So user can dial the numeric number to test echo voice test. This function is provided with server to make endpoint to test whether endpoint could talk through server normally. Specify echo test text’s name.
STUN Field name STUN NAT Transverse STUN Server Addr STUN Server Port STUN Effect Time Local SIP Port explanation Shows STUN NAT Transverse estimation, true means STUN can penetrate NAT, while False means not. Set your SIP STUN Server IP address Set your SIP STUN Server Port Set STUN Effective Time. If NAT server finds that a NAT mapping is idle after time out, it will release the mapping and the system need send a STUN packet to keep the mapping effective and alive. Set the SIP port.
If user makes the above configuration, after user dials 11 digit numbers started with from 135 to 139, the phone will send out 0 plus the dialed numbers automatically. Use this phone you can realize dialing out via different lines without switch in web interface. DIAL PEER Field name Phone number Destination Port Alias explanation There are two types of matching conditions: one is full matching, the other is prefix matching.
Note: There are four types of aliases. 1) add: xxx, it means that you need dial xxx in front of phone number, which will reduce dialing number length. 2) all: xxx, it means that xxx will replace some phone number. 3) del: It means that phone will delete the number with length appointed. 4) Rep: It means that phone will replace the number with length and number appointed. You can refer to the following examples of different alias application to know more how to use different aliases and this dial rule.
The phone will automatically send out alias number adding your dialed number, if your dialed number starts with your set phone number. You need set Phone Number, Alias and Delete Length. Phone number is XXXT and Alias is rep:xxx If your dialed phone number starts with your set phone number, the first digits same as your set phone number will be replaced by the alias number specified and New phone number will be send out. If your dialed phone number starts with your set phone number.
DSP Configuration Field name First Codec Second Codec Third Codec Forth Codec Fifth Codec Input Volume Hands-free Volume G729 Payload Length Handdown Time Ring Type Output Volume Ring Volume G722 Timestamps G723 Bit Rate Default Ring Type Signal Standard VAD explanation The fist preferential DSP codec: G.711A/u, G.722, G.723, G.729 The second preferential DSP codec: G.711A/u, G.722, G.723, G.729 The third preferential DSP codec: G.711A/u, G.722, G.723, G.729 The forth preferential DSP codec: G.711A/u, G.
Call Service Field name Hotline No Answer Time P2P IP Prefix Remote Record No Do Not Disturb Ban Outgoing Enable Call Transfer Enable Call Waiting Enable Three Way Call Accept Any Call Auto Answer Use Record explanation Specify Hotline number. If you set the number, you can not dial any other numbers. Specify No Answer Time Set Prefix in peer to peer IP call. For example: what you want to dial is 192.168.1.119, If you define P2P IP Prefix as 192.168.1., you dial only #119 to reach 192.168.1.119.
Server Auto handdown Black List The phone will hang up and return to standby automatically at hands-free mode Set Add/Delete Black list. If user does not want to answer some phone calls, add these phone numbers to the Black List, and these calls will be rejected. x and . are wildcard. x means matching any single digit. for example, 4xxx expresses any number with prefix 4 which length is 4 will be forbidden to dialed out DOT (.) means matching any arbitrary number digit. for example, 6.
Digital Map Configuration Field name End with "#" Fixed Length Time out explanation Set Enable/Disable the phone ended with “#” dial. Specify the Fixed Length of phone ending with. Set the timeout of the last dial digit. The call will be sent after timeout. Below is user-defined digital map rule: [] Specifies a range that will match digit. May be a range, a list of ranges separated by commas, or a list of digits. x Match any single digit that is dialed. .
4.3.4.4. Phone Book You can input the name, phone number and select ring type for each name here. Phone Book Field name explanation Shows the detail of current phonebook. Shows the name corresponding to the phone number Name Number Shows the phone number Ring Type Shows the ring type of the incoming call. Click “Modify” to change the selected information and click the “Delete” to delete the selected record. Notice: the maximum capability of the phonebook is 500 items 4.3.4.5.
Function Key Field name Contrast Luminance MWI Number explanation Set contrast of screen Set luminance of screen To listening record in server , we defined the function key F10 ,After you set it, you can pick up or hands-free, then press to listen record in server. Line: select SIP1, SIP2, SIP3, Dial peer, or IAX2 in function key type. After you set it, you pick up handset or hands-free, press this function key, then you can use the corresponding IP line.
l You can set speed dial function by Memory Key mode. For example, you need set speed dial 8000 via sip 1. Select memory key in F4’s function key type, then fill 8000@1/f in the corresponding right table. l You can set shortcut key of pbook, redial, DND, MWI, call forward, or callers by Key Event mode in function key type. Select key event in function key type, then fill F_PBOOK, F_REDIAL, F_DND, F_MWI, F_CFWD,or F_CALLERS in the corresponding right table. For example: 4.3.5. Maintenance 4.3.5.1.
Update Mode Different update modes: 1. Disable: means no update 2. Update after reboot: means update after reboot. 3. Update at time interval: means periodic update. 4.3.5.2. Syslog Config Syslog is a protocol which is used to record the log messages with client/server mechanism. Syslog server receives the messages from clients, and classifies them based on priority and type. Then these messages will be written into log by some rules which administrator can configure.
Config Setting Field name Save Config Backup Config Clear Config explanation you can save all changes of configurations. Click the Save button, all changes of configuration will be saved, and be effective immediately. . Right clicks on “Right click here…” and select “Save Target As….” then you will save the config file in .txt format user can restore factory default configuration and reboot the phone.
Update Field name explanation Click the browse button, find out the config file saved before or Web Update provided by manufacturer, download it to the phone directly, press “Update” to save. You can also update downloaded update file, logo picture, ring, mmiset file by web. Server Set the FTP/TFTP server address for download/upload. The address can be IP address or Domain name with subdirectory. Username Set the FTP server Username for download/upload.
Account Configuration Field name Keyboard Password explanation Set the password for entering the setting menu of the phone by the phone ‘s key board. The password is digit. This table shows the current user existed. User Name Set account user name. User Level Set user level, Root user has the right to modify configuration, General can only read. Password Set the password. Confirm Confirm the password.
If you modified some configurations which need the phone’s reboot to be effective, you need click the Reboot, then the phone will reboot immediately. Notice: Before reboot, you need confirm that you have saved all configurations.. 4.3.6. Security 4.3.6.1. MMI Filter MMI Filter User could make some device own IP, which is pre-specified, access to the MMI of the phone to config and manage the phone.
through the web. 4.3.6.2. Firewall Firewall Configuration In this web interface, you can set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet (input rule), or prevent unauthorized private network devices from accessing the Internet (output rule). Firewall supports two types of rules: input access rule and output access rule. Each type supports at most 10 items.
out access enable Input/Output Deny/Permit Protocol Type Port Range Src Addr Select it to Enable out_ access rule Specify current adding rule by selecting input rule or output rule. Specify current adding rule by selecting Deny rule or Permit rule. Filter protocol type. You can select TCP, UDP, ICMP, or IP. Set the filter Port range Set source address. It can be single IP address, network address, complete address 0.0.0.0, or network address similar to *.*.*.0 Des Addr Set the destination address.
DMZ config： In order to make some intranet equipments support better service for extranet, and make internal network security more effectively, these equipments open to extranet need be separated from the other equipments not open to extranet by the corresponding isolation method according to different demands.
NAT Configuration Field name IPSec ALG FTP ALG PPTP ALG explanation It is an encryption technology. Select it to enable IPSec ALG, the default is enable FTP is a service of connection layer which can transform intranet IP into extranet IP when intranet IP is sending out packet.
Outside Port Set the WAN port of the NAT mapping Notice: After finish setting, click the Add button to add new mapping table; click the Delete button to delete the selected mapping table. Shows the outside WAN port IP address and the inside LAN port IP address. Outside IP Set the outside Wan port IP address of DMZ. Inside IP Set the inside LAN port IP address of DMZ Click the Add button to add new table; click the Delete button to delete the selected mapping table.
VPN Configuration Field name VPN IP explanation Shows the current VPN IP address Select UDP Tunnel (VPN Tunnel) or VPN L2TP. You can choose only one for current state. After you select it, you’d better save configuration and reboot your phone.
Click Logout，and you will exit web page. If you want to enter it next time, you need input user name and password again. 5. Configuration via Keypad 5.1. Keypad introduction User can browse, modify or cancel via screen menu by using and v Use need input password (default 123),when login the menu (system config) 5.2.
6. Appendix 6.1. Specification 6.1.1. Hardware Item Adapter (Input/Output) port WSS530 Input: 100-240V Output: 5V 1A WAN 10/100Base- T RJ-45 for LAN LAN 10/100Base- T RJ-45 for PC Power Consumption Idle: 2.5W/Active: 2.8W LCD Size 128*64 dot matrix LCD Operation Temperature 0～40℃ Relative Humidity CPU SDRAM Flash 10～65% Dimension(L x W x H) Weight Broadcom 128M 32M 11.6×8×3 in.(295×205×75mm) 0.955kg 6.1.2.
l l l l l l l Support path, gruu Support SIP Privacy Support SMS Support Memo Support WMI Support Speed dial Support Alarm clock 6.1.3.
6.2. Digit-character map table Keypad Character Keypad 1@ Character 7PQRSpqrs 2AB C a b c 8TUVtuv 3DEFdef 9WXYZwxyz 4GHIghi */.
