ELECTRIC PRESSURE WASHER INSTRUCTION MANUAL HPI-1100 WARNING: Do not use the appliance without reading the instruction manual.
. TECHNICAL DATA CONTENT Chapter 1. Application 2. Technical data 3. Product overview 4. Safety symbols on the device and/or in the instructions 5. General safety instructions 6. Special safety instructions for this device 7. Operation instructions 8. Connection requirements 9. Instruction for use 10. After use instructions 11. Maintenance, cleaning and repair 12. Trouble shooting 13. WEEE - Waste of electric and electronic equipment 1. APPLICATION 14. Warranty Page 1 1 1 Motor Max. pressure Max.
4. SAFETY SYMBOLS ON THE DEVICE AND/OR IN THE INSTRUCTIONS Caution! Please read the accompanying documents! The symbol Caution! indicates a source of danger. It draws your attention to a working routine, a method of working, a condition or other situation which may lead to physical injury if performed incorrectly or with insufficient care. Warning Sign on the Device Never point the high-pressure jet at people, animals, the device itself or electrical parts. 5.
spray gun and the jet pipe as tightly as possible. If required, you should wear appropriate protective clothing as protection against spray. Never leave the device unattended as long as the main switch is turned on. During work breaks the manual spray gun should be secured by use of the lock. Here there is a Danger of Death Never operate the device in rooms where there is a risk of explosion. Never touch the mains plug with wet hands.
Caution: Make sure the lance (9) is properly fixed to the gun (7). 3. Attach the nozzles (10-15). Caution: When attaching the nozzle (10-15) the button (A) on the nozzle (10-15) should come out again. Check before activating the trigger that the nozzle (10-15) is properly fixed. 7.5 Start/stop of the machine The trigger gun (7) and lance (9) is affected by a thrust during operation therefore always hold it firmly with both hands. IMPORTANT: Point the nozzle at the ground. 1.
start again when you re-activate the trigger gun (7). 7.8 Angle Nozzle (optional) The angle nozzle (13) can be used for many applications e.g. cleaning the underbody of a car, underneath a lawn mower without being splashed back with debris, etc. 7.6 Adjustable Nozzle The pressure can be adjusted by turning the adjustable nozzle (10). WARNING: Do not do this under operation to avoid that the hand hits the jet.
9. INSTRUCTIONS FOR USE C D 9.1 Use The device is intended for private use only. Clean machines, vehicles, buildings, tools, facades, terraces, garden tools etc. with the high-pressure water jet. If necessary you can use detergents. Please use detergents sparingly, noting the quantities recommended by the producer. B A 8. CONNECTION REQUIREMENTS NOTE:The cleaning of motors/engines and other surfaces that may be covered with oil is only allowed in conjunction with an appropriate oil separator.
EN the high-pressure connection no longer contains any bubbles. Switch off the machine at the main switch(4) and screw the high-pressure hose (6) back on. always be emptied of water prior to storing as follows: 1. Stop the machine (press the start/stop switch (4) “O” and detach water hose, high pressure hose (6) and nozzle (10-15). 2. Restart the machine (4) and activate the trigger of the trigger gun (7). Let the machine run until no more water runs through the trigger gun (7) 3.
11.1 Cleaning of inlet filter Clean the water inlet filter regularly once a month or more frequently according to use. Carefully loosen the filter with a screwdriver and clean it. Check that it is intact before re-mounting it. The inlet filter must always be fitted inside the water inlet pipe to filter out sand, limestone and other impurities, as they will damage the pump valves. CAUTION: Failure to fit the filter will invalidate the warranty 11.
12. TROUBLE SHOOTING Symptom Machine refuses to start Cause Recommended action Machine not plugged in Plug in machine. Defective socket Try another socket. Fuse has blown Replace fuse. Switch off other machines. Defective extension cable Try without the extension cable. Check that hoses and connections are airtight. Pump is sucking air Fluctuating pressure Valves dirty, worn out or stuck Contact your nearest service centre.
13. WEEE - WASTE OF ELECTRIC AND ELECTRONIC EQUIPMENT The symbol on the product or on its packing indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Any transportation costs shall always be borne by the customer, unless agreed otherwise in writing. You can always obtain more information by the email realminfo@yahoo.com or at the number 888-899-1688. Zhejiang Xinchang Bigyao Power Tool Co., Ltd Head Office: Mengjiatang Industrial Zone, Xinchang County, Zhejiang Province, China USA Office: 101 wales avenue,Avon,MA 02322,United States Service Hotline: 888-899-1688 Email: realminfo@yahoo.
