User Manual

MOUNTING
Lever-Release Clamp
Simply open the lever to the fully
open position and top load your
gear. Close lever halfway shut and
plate can still be shifted for final
positioning. Close lever shut to lock
plate in place.
Screw-Knob Clamp
You may top load or side load
your gear, but side loading is
faster. To release, turn knob
counterclockwise one-half
turn and slide your gear out
of the clamp.
Note About Cable Releases & Tethering:
On some camera models, installing a cable may
prevent you from CENTERING the camera when
shooting in portrait. To solve this, some L-plates have
a mounting slot instead of a threaded
hole. To create additional clearance
on the side of the camera, loosen the
mounting screw slightly, slide the plate
away from the side of the camera, and
retighten screw.
PORTRAIT MODE
Switching back and forth from landscape to portrait
orientation is a snap with your RRS L-plate. Simply
open your quick-release clamp, remove camera with
its L-plate, re-mount in vertical orientation, and
close clamp.
GUARANTEE
ALL REALLY RIGHT STUFF BRAND PRODUCTS ARE
GUARANTEED TO THE ORIGINAL PURCHASER TO BE FREE
OF DEFECTS IN MATERIALS OR WORKMANSHIP FOR FIVE
(5) YEARS FROM THE DATE OF PURCHASE. PRODUCTS
WILL BE REPAIRED OR REPLACED AT OUR OPTION.
INSTALLATION
Wipe off bottom of camera to prevent trapping dirt
or grit. Looking at the front of the camera, place
the vertical dovetail on the right side. Use included
hex key to gently tighten screw, then check fit and
position vertical dovetail as close as possible to side
of camera. Firmly tighten mounting screw.
REMOVAL
When removing the plate, take care to pull the
plate away from the body of the camera as the
captive screw is being loosened. This prevents the
threads of the captive screw from damaging the slot
or threaded socket in the plate. If the screw needs to
be removed from the plate after it is removed from
the camera, locate the screw at the threaded socket
or threaded end of the slot and carefully guide the
screw threads into female threads in the plate.
USING THE QD SOCKET
Our QD socket accepts industry standard push-
button QD mounts. The QD socket must be kept free
of dirt or grit to allow the QD mount to fully seat
and snap into the socket. Always check that the
QD mount on your strap/swivel is fully seated
and completely engaged before use.
MOUNTING
Lever-Release Clamp
Simply open the lever to the fully
open position and top load your
gear. Close lever halfway shut and
plate can still be shifted for final
positioning. Close lever shut to lock
plate in place.
Screw-Knob Clamp
You may top load or side load
your gear, but side loading is
faster. To release, turn knob
counterclockwise one-half
turn and slide your gear out
of the clamp.
Note About Cable Releases & Tethering:
On some camera models, installing a cable may
prevent you from CENTERING the camera when
shooting in portrait. To solve this, some L-plates have
a mounting slot instead of a threaded
hole. To create additional clearance
on the side of the camera, loosen the
mounting screw slightly, slide the plate
away from the side of the camera, and
retighten screw.
PORTRAIT MODE
Switching back and forth from landscape to portrait
orientation is a snap with your RRS L-plate. Simply
open your quick-release clamp, remove camera with
its L-plate, re-mount in vertical orientation, and
close clamp.
GUARANTEE
ALL REALLY RIGHT STUFF BRAND PRODUCTS ARE
GUARANTEED TO THE ORIGINAL PURCHASER TO BE FREE
OF DEFECTS IN MATERIALS OR WORKMANSHIP FOR FIVE
(5) YEARS FROM THE DATE OF PURCHASE. PRODUCTS
WILL BE REPAIRED OR REPLACED AT OUR OPTION.
INSTALLATION
Wipe off bottom of camera to prevent trapping dirt
or grit. Looking at the front of the camera, place
the vertical dovetail on the right side. Use included
hex key to gently tighten screw, then check fit and
position vertical dovetail as close as possible to side
of camera. Firmly tighten mounting screw.
REMOVAL
When removing the plate, take care to pull the
plate away from the body of the camera as the
captive screw is being loosened. This prevents the
threads of the captive screw from damaging the slot
or threaded socket in the plate. If the screw needs to
be removed from the plate after it is removed from
the camera, locate the screw at the threaded socket
or threaded end of the slot and carefully guide the
screw threads into female threads in the plate.
USING THE QD SOCKET
Our QD socket accepts industry standard push-
button QD mounts. The QD socket must be kept free
of dirt or grit to allow the QD mount to fully seat
and snap into the socket. Always check that the
QD mount on your strap/swivel is fully seated
and completely engaged before use.