Installation Guide

BACK TO
NATURE
READY-STRIP
TM
SAFER PAINT & VARNISH REMOVER
TECHNICAL DATA SHEET
I. Description: Ready-Strip Plus, now 50% stronger, is a one
of a kind, environmentally friendly, paint and varnish remover
capable of removing up to 7 layers in a single application using
a stripping tool. The revolutionary "Color Change" feature
signals the time for paint removal. The stripper is applied to
the surface and turns off-white or a pale green when the
paint or varnish is READY to be removed. Ready-Strip Plus
is non-flammable, biodegradable, virtually odorless and can be
cleaned up with water. It does not contain methylene chloride,
caustic, flammable chemicals or harmful vapors like many
traditional strippers. Ready-Strip Plus avoids the uncertainty
associated with other strippers that are ineffective if removed
too soon, or dry out and not work if left on too long. Ready-
Strip Plus eliminates the guesswork. Unlike other strippers,
Ready-Strip Plus is a semi-paste and therefore truly clings to
vertical surfaces.
II. Types of Paint Removed: Ready-Strip Plus can remove
most varieties of household paints & varnishes which are water
or oil-based including, latex, stains, enamels, lacquers, clear
paints as well as polyurethanes, etc.
III. Surfaces: Ready-Strip Plus can be applied on a multitude
of interior and exterior surfaces including wood, plaster,
concrete, brick, stone, masonry, marble, metal and fiberglass,
etc. Ready-Strip Plus will not damage plaster or wood (discolor
or raise the grain) or affect any surface it is used on. Ready-
Strip Plus is not to be used on sheetrock, plastic, rubber or
linoleum surfaces.
IV. Instructions:
A. TEST PATCH - Since it is often hard to know the
type or amount of paint or varnish on a surface, a small test
area should be tested first to determine whether the desired
results will be achieved.
B. Preparation- Mask any areas not being stripped
with plastic and masking tape.
C. Application and Removal- Apply Ready-Strip Plus
liberally to the surface with a brush, medium sized nap paint
roller, or putty knife so that the remover completely "masks" or
covers the color of the surface to be stripped. Do not attempt
to brush out too thin like a coat of paint. It covers
approximately 50 sq. ft. per gallon. Apply at temperatures
between 60
0
F and 80
0
F. When the stripper turns off-white or a
pale green, it may form an eggshell like skin to lock in the
stripping action. Misting the area to be removed with water or
After-Strip Paint Remover Wash prior to actual removal will
soften the skin and make lifting of the paint or varnish easier.
After the stripper has turned off-white or a pale green, use a stiff
putty knife to lift paint from flat surfaces or a stiff bristle brush for
detailed areas. After initial lifting, use a nylon bristle brush or
stripping pad to scrub surface. The time the stripper takes to
turn off-white or pale green may vary depending upon the type
and amount of paint, the surface and temperature. . Typical
color change usually occurs within 4 - 24 hours. Paint or
varnish removal may take place prior to the “Color Change”,
although the “Color Change” will indicate the end of stripping
action. Apply After-Strip Paint Remover Wash or light amounts
of water for final clean up of residue. Surface should be
completely dry before repainting. No need to neutralize (acid
wash) surface. Clean tools promptly after use with soap and
water.
D. Removal Time - On interior surfaces, the softened
paint/varnish may remain moist under the eggshell skin for
several days for easy removal. On exterior surfaces, due to the
potential for higher temperatures and direct sunlight, the “Color
Change” may be greatly accelerated (1–8 hours). The paint
should be removed shortly after “Color Change” to prevent the
stripper from drying out. Not advisable for outdoor decks
E. Hints – If Ready-Strip Plus is applied too thinly, left
on too long, or due to excessive heat conditions, the applied
area is difficult to scrape, try the following: 1) Mist the applied
area with water or After-Strip, wait 5-15 minutes and remove; 2)
Reapply Ready-Strip Plus over itself, wait 15-30 minutes and
remove; 3) if 1) or 2) does not work, scrape off and reapply.
If product freezes in bucket, let thaw and stir vigorously until
product is consistent.
V. Safety Instructions: Due to the sensitive nature of certain
person's skin, rubber gloves and safety glasses are
recommended . Avoid eye contact. If eye contact occurs
immediately flush with plenty of water for 15 minutes. Avoid
prolonged and repeated contact with skin. If skin contact
occurs, wash with soap and water. Maintain adequate
ventilation especially in confined areas. If spraying is expected
use NIOSH approved chemical cartridge (organic vapor)
respirators. If swallowed do not induce vomiting. Give 1 or 2
glasses of water and call a physician immediately.
SUNNYSIDE CORPORATION 225 CARPENTER AVENUE WHEELING, IL 60090 PH:847-541-5700 FAX:[phone]