MEETS NFPA 1851: 2020 REQUIREMENTS READY RACK EXTRACTOR OWNER’S MANUAL EW30 Extractor DIMENSIONS OF THE WASHER: LENGTH: 29.0” (L) DEPTH: 32.0” (D) HEIGHT: 40.8” (H) DEPTH WITH DOOR OPEN: 53.
PRODUCT FEATURES PRODUCT FEATURES DIRECT DRIVE SYSTEM The advanced brushless DC motor drives the drum directly without using a belt and pulley. TILTED DRUM AND EXTRA LARGE DOOR OPENING The tilted drum and extra large opening makes it possible to load and unload clothing more easily. ULTRA CAPACITY The larger drum enables more tumbling action and greater centrifugal force, but also less tangling and wrinkling of the laundry. SEE-THROUGH DOOR AND BIG DOOR You can see the laundry throughout the cycle.
IMPORTANT SAFETY INSTRUCTIONS 3 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death. Your Safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death. BASIC SAFETY PRECAUTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.
IMPORTANT SAFETY INSTRUCTIONS 5 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death. SAFETY INSTRUCTIONS FOR INSTALLATION WARNING To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE WARNING For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death. SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL WARNING To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.
PARTS AND ACCESSORIES PARTS AND ACCESSORIES Parts Detergent dispenser drawer Water inlets Control panel Shipping bolts Door Power cord Door seal Magnet Door Plunger (see page 2) Drain hose Tub Drain pump filter cover Drain pump filter Drain hose Accessories (-) (+) Hot and Cold Water Hoses Wrench (for removing shipping bolts and adjusting leveling feet) Non-skid pads Hole cap (5) (for securing auto dosing hole) Caps (4) (for covering shipping bolt holes) Harness (for connecting auto dos
CONTROL PANEL FEATURES CONTROL PANEL FEATURES Display LED Optional cycle The display shows t h e remaining time and programming options. Error codes are also displayed here. Super Wash: Wash cycle with longest run time. Start/Pause button The Start/Pause LED flashes when the cycle has been chosen. Cycle button Status LED Press the CYCLE button to select the desired cycle based on laundry types and conditions. Blood Bourne Increased temperature for cleaning of heavily soiled clothing.
INSTALLATION INSTRUCTIONS 9 INSTALLATION INSTRUCTIONS Checking and choosing the proper location Install the washing machine on a solid floor that is strong and rigid enough to support the weight of the washing machine, even when fully loaded, without flexing or bouncing. If the floor has too much flex, you may need to reinforce it to make it more rigid. If the floor is not solid, it may cause severe vibration and noise. 1 Installing on a floor 23.3” (59.1 cm) Clean the floor before installation. 32.
INSTALLATION INSTRUCTIONS Unpacking and removing shipping bolts When removing the washer from the carton base, be sure to remove the foam drum support in the middle of the carton base. If you must lay the washer down to remove the base packaging materials, always lay it carefully on its side. DO NOT lay the washer on its front or back. FoamTub Support 1 NOTE • Save the bolt assemblies for future use.
INSTALLATION INSTRUCTIONS 11 Connecting the water lines 1 Check the rubber seals on both sides of the hose. - Insert a rubber seal into the threaded fittings on each hose to prevent leaking. Rubber seal 4 Rubber seal Connect the hoses to the water inlets tightly by hand and then tighten another 2/3 turn with pliers. - Connect the blue hose to the cold water inlet and the red hose to the hot water inlet.
INSTALLATION INSTRUCTIONS Connecting the drain line Secure the drain hose in place to prevent moving and leaking. Using a laundry tub 1 NOTE • The drain hose should be properly secured. Failure to properly secure the drain hose can result in flooding and malfunction. • Total height of the hose end should not exceed 96 inches (244.8 cm) from the bottom of the washer. • The drain must be installed in accordance with any applicable local codes and regulations.
INSTALLATION INSTRUCTIONS Leveling the washing machine 4 Check the washing machine’s level. - Check the precise level by rocking the top edges of the washing machine or placing a level on the washing machine. The slope beneath the washing machine must not exceed 1°, and all four leveling feet must rest firmly on the floor. Level Check the washing machine’s level again. - Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock.
OPERATING YOUR WASHER OPERATING YOUR WASHER 1. Ready mode The cycle LEDs flash at the same time, and displays PUSH. 2. Select the cycle Press the desired button and press the Start button. The display LED will show the remaining time and the selected cycle starts. 3. Change course You cannot change the cycle while the machine is running. 4. Cycle finish The machine stops and LED display shows “End” with beeper sound.
OPERATING YOUR WASHER INSTALLING A PUMP Channel # Type Wire Color Signal Type Input Period 1 N/A Black - N/A 4 N/A Brown + N/A 5 N/A Orange + N/A 6 N/A Yellow + N/A 7 Main Wash Blue + 8 N/A Red + Main Wash Phase N/A - The Blue and Black wire will be used for connecting the extractor to a single pump. - The Blue wire triggers the pump to run detergent into nozzle 1 of the extractor. - All other colored wires can be taped or capped off.
MAINTENANCE MAINTENANCE Cleaning the drum 1 Wear rubber gloves and protective goggles. Using the washing machine in a humid space for a long period of time may lead to a buildup of black mold and germs in the air inside the washer tub and affect your health. If you clean the washer tub regularly on a monthly basis Using the “Blood Bourne” (hot) cycle it will keep the washer tub clean for hygienic use. 2 Dilute 3/4 cup (177 ml) of liquid chlorine bleach in 1 gallon (3.8 L) of water.
MAINTENANCE 3 Cleaning the water inlet filters Clean the water inlet filters periodically to prevent clogging. Take extra care to clean the water inlet filters for areas using hard water. Water may not be supplied if there are foreign objects, such as rust, sand, or stones in the water inlet filters. 1 Pull out the plug to turn off the washing machine. 2 4 Unclip the drain hose and remove the plug from the drain hose to drain the remaining water. Twist the pump filter counterclockwise to remove.
ERROR MODE 18 ERROR MODE Meaning of Error Codes that LED displays during occurrence of problem. Problem • • • • Possible Cause Solution Water supply is not adequate in area. Water supply taps are not completely open. Water inlet hose is bent. The filter of the inlet hose clogged. Check another tap in the house. Fully open tap. Straighten hose. Check the filter of the inlet hose. • Drain hose is bent or clogged. • The drain filter is clogged. • Load is too small. • Load is out of balance.
POWER FAIL RECOVERY& DEFAULT WASHER SETTINGS & SPECIFICATIONS POWER FAIL RECOVERY In case of power failure, the machine stops running but the time display remains on, showing the time just before power failure. SPECIFICATIONS Model Name Front-loading Washing Machine: EW30 Power supply 120 V~ 60 Hz Size 29.0”(L) X 32.0”(D) X 40.8”(H), 53.9”(D with door open) 73.7 cm (L) X 81.4 cm (D) X 103.6 cm (H), 137.0 cm (D with door open) Weight 221 lbs (100.25 kg) Wash capacity 5.2 cu.ft (IEC: 6.0 cu.
