User Manual

ManualsBrandsREACT HEALTH ManualsPulse OximeterREACT HEALTH PO2BLK Pulse Oximeter

! Do not immerse the device in liquid.

! It is recommended that the device should be kept in a dry environment. Humidity may reduce the useful life of the device, or even damage it.

9 Troubleshooting

Trouble Possible Reason Solution

The SpO

and Pulse Rate can not be

displayed normally

1. The nger is not properly positioned.

2. The user’s SpO

is too low to be detected.

1. Place the nger properly and try again.

2. Try again; Go to a hospital for a diagnosis if you

are sure the device works all right.

The SpO

and Pulse Rate are not

displayed stably

1. The nger is not placed inside deep enough.

2. The nger is shaking or the user is moving.

1. Place the nger properly and try again.

2. Insure user is still with minimal movement.

The device can not be turned on

1. The batteries are drained or almost drained.

2. The batteries are not inserted properly.

3. Device malfunction.

1. Change batteries.

2. Reinstall batteries.

3. Please contact the local service center.

The display is off suddenly

1. The device will power off automatically

when it gets no signal within 5 seconds.

2. The batteries are almost drained.

1. Normal.

2. Change batteries.

10 Key of Symbols

Symbol Description

Type BF

Refer to instruction manual/booklet

SpO

The pulse oxygen saturation(%)

PRbpm ♥

Pulse rate (bpm)

The battery voltage indication is decient (change the battery in time avoiding the inexact measure)

1. no nger inserted

2. An indicator of signal inadequacy

battery positive electrode

battery negative electrode;

Power switch

Serial number

Alarm inhibit

WEEE (2002/96/EC)

IP22

Ingress of liquids rank

This item is compliant with Medical Device Directive 93/42/EEC of June 14, 1993, a directive of the

European Economic Community

EUROPEAN REPRESENTATIVE

Manufacturer

Manufacture Date

Storage and Transport Temperature limitation

Storage and Transport Humidity limitation

Storage and Transport Atmospheric pressure limitation

This side UP

Fragile, handle with care

Keep dry

Recyclable

-40˚C

60˚C

1060hPa

500hPa

-40˚C

60˚C

-40˚C

60˚C

-40˚C

60˚C

95%

Appendix:

Electromagnetism Compatibility

Guidance and manufacture’s declaration – electromagnetic emissions-

for all EQUIPMENT and SYSTEMS

Guidance and Manufacture’s Declaration – Electromagnetic Emission

The PO2BLU/PO2BLK is intended for use in the electromagnetic environment specified below.

The customer of the user of the PO2BLU/PO2BLK should assure that it is used in such and environment.

11 Function Speciﬁcation

Display Information Display Mode

The Pulse Oxygen Saturation(SpO

) Digital

Pulse Rate (BPM) Digital

Pulse Intensity (bar-graph) Digital bar-graph display

SpO

Parameter Specication

Measuring range 0%~100%, (the resolution is 1%).

Accuracy 70%~100%: ±2%, Below 70% unspecied

Optical Sensor

Red light (wavelength is 660nm)

Infrared (wavelength is 880nm)

Pulse Parameter Specication

Measuring range 30bpm~250bpm (the resolution is 1 bpm)

Accuracy ±2bpm or ±2% select larger

Pulse Intensity

Range Continuous bar-graph display, the higher display indicate the stronger pulse.

Battery Requirement

1.5V (AAA size) alkaline batteries × 2 or rechargeable battery

Battery Useful Life

Two batteries can work continually for 24 hours

Dimensions and Weight

Dimensions 57(L) × 31(W) × 32(H) mm

Weight About 50g (with the batteries)

Emission test Compliance Electromagnetic environment – guidance

RF emissions

CISPR 11

Group 1

The PO2BLU/PO2BLK uses RF energy only for its internal function. Therefore, its

RF emissions are very low and are not likely to cause any interference in nearby

electronic equipment.

RF emission

CISPR 11

Class B

The PO2BLU/PO2BLK is suitable for use in all establishments, including domestic

establishments and those directly connected to the public low-voltage power supply

network that supplies buildings used for domestic purposes.

Harmonic emissions

IEC 61000-3-2

N/A

Voltage uctuations/

icker emissions

IEC 61000-3-3

N/A

Guidance and manufacture’s declaration – electromagnetic immunity –

for all EQUIPMENT and SYSTEMS

Guidance and Manufacture’s Declaration – Electromagnetic Immunity

The PO2BLU/PO2BLK is intended for use in the electromagnetic environment specified below.

The customer or the user of PO2BLU/PO2BLK should assure that it is used in such an environment.

Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance

Electrostatic discharge

(ESD)

IEC 61000-4-2

±6 kV contact

±8 kV air

±6 KV contact

±8 kV air

Floors should be wood, concrete or ceramic tile. If oor are

covered with synthetic material, the relative humidity should

be at least 30%

Electrical fast

transient/burst

IEC 61000-4-4

±2 kV for power supply

lines

N/A

Mains power quality should be that of a typical commercial or

hospital environment.

Surge

IEC 61000-4-5

±1 kV differential mode N/A

Mains power quality should be that of a typical commercial or

hospital environment.

Voltage dips, short

interruptions and

voltage variations on

power supply input

lines

IEC 61000-4-11

<5% UT

(>95% dip in UT)

for 0.5 cycle

40% UT

(60% dip in UT)

for 5 cycles

70% UT

(30% dip in UT)

for 25 cycles

<5% UT

(>95% dip in UT)

for 5 sec

N/A

Mains power quality should be that of a typical commercial

or hospital environment. If the user of the PO2BLU/PO2BLK

requires continued operation during power mains

interruptions, it is recommended that the PO2BLU/PO2BLK

be powered from an uninterruptible power supply or a battery.

Power frequency

(50/60Hz)

Magnetic eld

IEC-61000-4-8

3 A/m 3 A/m

Power frequency magnetic elds

sould be at levels characteristic of a typical location in a

typical commercial or hospital environment.

NOTE UT is the a.c. mains voltage prior to application of the test level.

Guidance and Manufacture’s Declaration – Electromagnetic Immunity –

for EQUIPMENT and SYSTEMS that are not LIFE-SUPPORTING

Guidance and manufacture’s declaration – electromagnetic immunity

The PO2BLU/PO2BLK is intended for use in the electromagnetic environment specified below.

The customer or the user of PO2BLU/PO2BLK should assure that it is used in such an environment.

Immunity test IEC 60601 test level Compliance level Electromagnetic environment - guidance

Radiated RF

IEC 61000-4-3

3 V/m

80 MHz to 2.5 GHz

3 V/m

Portable and mobile RF communications equipment should

be used no closer to any part of the PO2PNK/PO2BLK,

including cables, than the recommended separation distance

calculated from the equation applicable to the frequency of

the transmitter.

Recommended separation distance

80 MHz to 800 MHz

800 MHz to 2.5 GHz

Where P is the maximum output power rating of the

transmitter in watts (W) according to the transmitter

manufacturer and d is the recommended separation

distance in metres (m).

Field strengths from xed RF transmitters, as determined

by an electromagnetic site survey,

should be less than the

compliance level in each frequency range.

Interference may occur in the vicinity of equipment marked

with the following symbol:.

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reection from structures, objects

and people.

Field strengths from xed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM

radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF

transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the PO2BLU/PO2BLK is used

exceeds the applicable RF compliance level above, the PO2BLU/PO2BLK should be observed to verify normal operation. If abnormal performance

is observed, additional measures may be necessary, such as reorienting or relocating the PO2BLU/PO2BLK .

Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m.

Recommended Separation Distances between

portable and mobile RF communications equipment and the PO2BLU/PO2BLK

The PO2BLU/PO2BLK is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of

the PO2BLU/PO2BLK can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications

equipment (transmitters) and the PO2BLU/PO2BLK as recommended below, according to the maximum output power of the communications equipment.

Rated maximum

output power of

transmitter

(W)

Separation distance according to frequency of transmitter

(m)

150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2.5 GHz

0.01 0.12 0.12 0.23

0.1 0.39 0.37 0.74

1 1.17 1.17 2.33

10 3.69 3.69 7.38

100 11.67 11.67 23.33

For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the

equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the

transmitter manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reection from structures, objects

and people.

3958 0819 pulseoximeter