User's Manual

ControlPanelForStairwell(XS)Fixtures
FloorX1DialSwitch:
Thisdialissetto
indicatethefloora
particularfixtureis
beinginstalledon.If
thefixtureisbeing
installedonthe4
th
floor,thisdialwould
besetto“4”.Ifthe
fixtureisbeing
installedonthe23
rd
floorthisdialwouldbe
setto“3”,etc.
StairwellDialSwitch:Some
buildingshavemorethanone
stairwell.Thisswitchhelpsto
keepfixturesinonestairwell
fromtalkingtofixturesin
anotherstairwell.Ifyouhave
onestairwell,useasmall
straightslotscrewdriverand
setthedialto
“1”.Formultiple
stairwellswithinabuilding,set
thedialaccordingly.
Timer:Oncethefixtureseesmotionwithinthe
stairwellitwillimmediatelyilluminatetofullintensity.
Asmallscrewdriverisusedtoadjustthe“Timer”.
ThisTimeradjuststhelengthoftimethatthefixture
remainsonatfullpower
priortoreturningtothe
“DIM”setting.TurningtheTimerallthewaytothe
left(counterclockwise)willkeepthefixtureonat
highpowerforonly10‐seconds.TurningtheTimerall
thewaytotheright(clockwise)willkeepthelightson
atfullpowerfor5‐
minutesafterthesensorseesits
lastmotion.Thetimecanalsobesetanywhere
between10‐secondsand5‐minutesbypositioning
theTimeraccordingly.
StatusIndicatorLED:Thisisa
bi‐coloredLED(RedorGreen).
ThisLEDprovidestheoperator
withthecurrentsystemstatus.
Seethetable
onthenextpage
foradetaileddescriptionof
thevariousindications.
Self‐Diagnostic:Periodicallyit’sagood
ideafortheoperatorstopushtheSelf‐
Diagnosticbuttontorunthebuilt‐in
testingprogram.ResultsoftheSelf‐
Diagnostictestarereportedonthe
“DIAG”LEDIndicator.Seethetable
on
thenextpageforadetaileddescription
oftheindications.
Self‐DiagnosticStatusLED:Thisis
abi‐coloredLEDs(RedorGreen).
ThisLEDprovidetheoperator
withtheself‐diagnosticteststatus
andresults.Seethetableonthe
nextpageforadetailed
descriptionoftheindications.

6
FloorX10DialSwitch:This
dialissettoindicatethe
flooraparticularfixtureis
beinginstalledon.Ifthe
fixtureisbeinginstalledon
floors1‐ 9,thisdialwould
besetto“0”.Ifthefixture
isbeinginstalledonfloors
10– 19,thisdialwouldbe
set
to“1”.Ifitisbeing
installedonfloors20– 29,
thisdialwouldbesetto“2”,
etc.
EXAMPLE#1:Ifafixtureisbeinginstalledinthesecondstairwellofabuildingonthe17
th
floor,thedialindicators
wouldbesetlikethis:217.
EXAMPLE#2:Ifafixtureisbeinginstalledinabuildingwithonlyonestairwellonthelandingbetweenfloors5and
6,thedialindicatorswouldbesetlikethis:105.
NOTE:Landingsbetweenfloorsshouldhave
thesamedialsettingsasthefloorjustbelowit…i.e.Afixtureinstalled
onalandingbetweenfloors2and3shouldhavethesamedialsettingsasthefixtureonfloor2.
XeleumLighting,LLC.333NorthBedfordRd.MountKisco,NY10549*Phone954‐617‐8170*Fax954‐571‐9777*www.xeleum.com
ArtemisSeriesofLowOccupancyLED
CeilingMountedFixtures(IncludingStairwells)
Installation&OperationGuide
STAIRWELLX10FLOORX1
DIM
HILOW
POWER
HILOW
“DIM”Settingcontrols
thelightlevelwhenthe
stairwellisun‐occupied.
“POWER”Setting
controlsthelight
levelwhenthe
stairwellisoccupied.
STAIRWELLX10FLOORX1
TEST
DIAG.STATUS