Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Low Occupancy Fixture XL Stairwell Fixture XS Basic Fixture XB 1 Xeleum Lighting, LLC. 333 North Bedford Rd. Mount Kisco, NY 10549 * Phone 954‐617‐8170 * Fax 954‐571‐9777 * www.xeleum.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Please read these instructions carefully, and keep them for future reference. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS. b) Do not use outdoors. c) Do not let power supply cords touch hot surfaces. d) Do not mount near gas or electric heaters.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide PARTS & TOOLS REQUIRED: Artemis Stairwell Fixture Wire Nuts Drill and Masonry Drill Bits (Not provided) Flat Blade Screwdriver (Not Provided) Phillips Screwdriver (Not Provided) Anchors & Mounting Hardware (Not Provided) Note: Ensure compliance with local codes and ordinances. WARNING: Turn power off at circuit breaker or fuse box. Do not rely on a wall switch alone to turn off power.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Installation Step Description 1 Remove the fixture from the packaging and make sure it has arrived in good condition. Place the fixture on a flat surface and remove two screws which secure the back‐box to the light engine (located on either side of the fixture in the middle and just behind the lens).
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Installation (cont.) Step 6 7 8 Description Image Feed the battery connector through the opening in the battery holder you just removed. Place the other end of the battery in the corresponding holder. Use a Philips head screwdriver and re‐install the battery holder. Plug the white connector coming out of the battery into the matting connector inside the back box.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Control Panel For Stairwell (XS) Fixtures Self‐Diagnostic: Periodically it’s a good idea for the operators to push the Self‐ Diagnostic button to run the built‐in testing program. Results of the Self‐ Diagnostic test are reported on the “DIAG” LED Indicator. See the table on the next page for a detailed description of the indications.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Control Panel For Low Occupancy (XL) Fixtures Self‐Diagnostic Status LED: This is a bi‐colored LEDs (Red or Green). This LED provide the operator with the self‐diagnostic test status and results. See the table on the next page for a detailed description of the indications.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Control Panel LED Indicator Message Interpretation “Only For Fixtures (XS & XL) with Battery Back‐Up” Once the fixture has been properly secured to the ceiling and powered, two Indicator LEDs can be seen on the control panel on the side of the fixture. The one to the left (when looking at the control panel) is the Diagnostic LED Indicator. The one to the right is the Status LED Indicator.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide “DIM and POWER” Settings For Artemis Fixtures There are very stringent illumination regulations governing fixtures intended for use in stairwells. Xeleum’s XS Artemis fixtures are specifically design to surpass these requirements, and have been validated with 3rd party testing and certification. As such, neither the POWER (occupied) and DIM (un‐occupied) settings can be turned off.
Artemis Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide Caution: Cet appareil est conforme à la Partie 15 des règlements de la FCC et aux normes RSS de l’Industrie du Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer des interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences qui peuvent provoquer un fonctionnement indésirable.
