User's Manual

ManualsBrandsRDI Technology ManualsElectronicsHOME VIEWER

Specifications

LCD Monitor

Multi-camera Operation

If you use the multi camera, you must set the Dip-switch for each cam-

eras and the LCD monitor. The LCD monitor system is designed to work

with up to three cameras. Additional cameras have to be purchased.

• Dip-switch positon of the LCD monitor

You can find the dip-switch on the battery box as shown below.

• Dip-switch positon of Wireless Camera

You can find the dip-switch on the battery box as shown below.

Battery installation guide.

When you use the Wireless camera system without the supplied adapter,

you can use the Wireless system by using four batteries.

Detach the battery cover on the camera and LCD monitor, and insert

four AA size batteries on the with 3 and # aligned correctly as shown

below.

Note : Do not mix old and new batteries and never mix different types

of batteries such as standard, alkaline, etc.

Trouble shooting

Check the following guide for the possible cause of a problem before

contacting service.

Wireless Camera

Antena

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the

user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be

of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence

of important operating and maintenance (servicing) instructions in the literature accompanying

the product.

FCC WARNING : This equipment may generate or use radio frequency energy. Changes or modifications to

this equipment may cause harmful interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or

modification is made.

Regulatory Notices For U.S.A

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-

ference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

•Asuitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in

the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equiva-

lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s

instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall

be provided with brushings.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference

in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local

codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with

liquids, such as vases, should be placed on the apparatus.

Important Safety Instructions

LG WIRELESS HOME VIEWER

Instruction Manual

Models : LSP-R1000

LSP-R1100

Before installing, operating or adjusting this

product, please read this instruction booklet

carefully and completely.

1 32

Set the camera 1 in

use.

Set the camera 1 and 2

in use.

Set the all 3 cameras in

use (Default setting).

Set the camera as

channel 1 (Default set-

ting).

Set the camera as

channel 2.

Set the camera as

channel 3.

Item Description

Frequency Range 2.400 --- 2.483Ghz

Polarizaion Monopole

SWR < 2 : 1

Gain 0 dB

Impendance 50 Ohm

Outline Size øı2x85mm (Transmitter)/

øı2x145mm (Receiver)

Item Description

Rated Voltage DC 9 V

Rated Current 800 mA

Frequency Range 2.4~2.48 GHz

Frequency 2.41, 2.44, 2.47 Ghz

Intermediate Frequency 480MHz

Type of Radio Waves Analog

Display Mode TMR

Display Size (Diagonal) 2.5 inch (LSP-R1000),

1.8 inch (LSP-R1100)

Number of Dots(HxV) 882x228 Dot

Dot Pitch (H x V) 0.056 x 0.168 mm

Color Number Full Color/16 Million

Viewing Angle U/D: 17/45o L/R: 45/45o

Brightness 250cd/m2

Contrast Rate 200:1

Light Source Type LED

TV System NTSC/PAL (Color) Standard

Color Configuraton R.G.B Strip

Overall Size 75mm (W) x 118mm (H) x 46mm (D)

Weight 180g

Operating Temperature -10° to 40°

Operating Humidity Less than 85%

Item Description

Rated Voltage DC 9 V

Rated Current 400 mA

Transmit Power Less than 10mW

Frequency Range 2.4~2.48 GHz

Frequency 2.41, 2.44, 2.47 Ghz

Modulation Method FM

Oscillation Method PLL

Image Sensor 1/3'' CMOS IC

Integrated Lens 5.6mm, F1.8 Fixed Focus

TV System NTSC/PAL (Color) Standard

Auto Electronic Exposure 1/60~1/15000 sec.

Min Illumination 0.5 Lux

Resolution 360 Horizontal TV lines

Signal/Noise Ratio 48dB

Overall Size 95mm W x 107mm H x 62mm D

Weight 100g (Without Battery)

Operating Temperature -10° to 40°

Operating Humidity Less than 85%

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

1. Read these instructions. - All these

safety and operating instructions

should be read before the product is

operated.

2. Keep these instructions. - The

safety, operating and use instructions

should be retained for future refer-

ence.

3. Heed all warnings. - All warnings on

the product and in the operating

instructions should be adhered to.

4. Follow all instructions. - All operat-

ing and use instructions should be

followed.

5. Do not use this apparatus near

water. - For example: near a bath

tub, wash bowl, kitchen sink, laundry

tub, in a wet basement; near a swim-

ming pool; etc.

6. Clean only with dry cloth. - Unplug

this product from the wall outlet

before cleaning. Do not use liquid

cleaners.

7. Do not block any ventilation open-

ings. Install in accordance with the

manufacturer’s instructions. - Slots

and openings in the cabinet are pro-

vided for ventilation, to ensure reli-

able operation of the product, and to

protect it from over- heating. The

openings should never be blocked by

placing the product on a bed, sofa,

rug or other similar surface. This

product should not be placed in a

built-in installation such as a book-

case or rack unless proper ventilation

is provided and the manufacturer’s

instructions have been adhered to.

8. Do not install near any heat

sources such as radiators, heat

registers, stoves, or other appara-

tus (including amplifiers) that pro-

duce heat.

9. Do not defeat the safety purpose

of the polarized or grounding-type

plug. A polarized plug has two

blades with one wider than the

other. A grounding type plug has

two blades and a third grounding

prong. The wide blade or the third

prong are provided for your safety.

If the provided plug does not fit

into your outlet, consult an electri-

cian for replacement of the obso-

lete outlet.

10. Protect the power cord from

being walked on or pinched par-

ticularly at plugs, convenience

receptacles, and the point where

they exit from the apparatus.

11. Only use attachments/acces-

sories specified by the manufac-

turer.

12. Use only the cart,

stand, tripod,

bracket, or table

specified by the

manufacturer, or

sold with appara-

tus. When a cart is used, use

caution when moving the cart/

apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus during

lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified

service personnel. Servicing is

required when the apparatus has

been damaged in any way, such

as power- supply cord or plug is

damaged, liquid has been spilled

or objects have fallen into the

apparatus, the apparatus has

been exposed to rain or mois-

ture, does not operate normally,

or has been dropped.

P/NO : MFL3058013?

Symptom

Abnormal or no picutre

Interference on

Camera picture

Audio problems

Correction

• Check the connection.

• Plug the power cord into the wall

outlet securely.

• Make sure the camera(s) and LCD

monitor switched on.

• Maker sure rechargeable battery is

charged.

•Check the batteries polarity with 3

and # aligned correctly.

• Make sure each camera is within

range, and that no large obstuctions

are blocking the signal.

•Try repositioning the camera, moni-

tor or both to impove the reception

quality.

• Reposition other nearby equipment

transmitting on the 2.4GHz frequen-

cy.

• Ensure the volume is turned up suf-

ficiently on the monitor.

• Make sure the sound is within the

microphone range.

• If the units emit a loud wailing

sound(feeds back), try moving the

camera away from the monitor or

angle the monitor differently.

1 32

DC IN 6V

Rear of the camera.

Rear of the LCD monitor.

FCC NOTE:

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY

UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S

AUTHORITY TO OPERATE THE EQUIPMENT.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)•This device may not cause harmful interference.

2)•This device must accept any interference received including interference that may cause undesired operation