VARIO-LINE VLA-120 C / VLA-240 C VARIO-LINE P.A.
VLA-120 C / VLA-240 C VARIO-LINE SAFETY INSTRUCTIONS SICHERHEITSHINWEISE Read all safety instruction before operating the amplifiers. 1. Install equipment as follow condition: - Install at flat place, not bending curved. - Do not install near the water and moisture. - Locate power amplifier away from heat source, such as radiators or other device that produce heat. - Do not drop objects or spill liquids into the inside of amplifier. 2. Keep in mind the following when connecting amplifier.
VARIO-LINE VLA-120 C / VLA-240 C MOUNTING MONTAGE COOLING KÜHLUNG Amplifier racking size for VLA series are designed for standard 19" rack mounting with additional left, right bracket. Please pay close attention to the cooling requirements. Never block the air vents in the sides and front of the amplifier the following is figure of air-flow.
VLA-120 C / VLA-240 C VARIO-LINE AMP SECTION Hauptmerkmale - AUTOMATIC VARIABLE SPEED FAN - OVER CURRENT PROTECTION - OVER HEATING PROTECTION - LOAD SHORT CIRCUIT PROTECTION - BUILT IN L.P.F.
VARIO-LINE VLA-120 C / VLA-240 C - REMOTE 2 VOLUME / EQ VOLUME - REMOTE 2 Regler / EQ Regler Remote 2 volume control / EQ control let you adjust input 2 level and REMOTE CONTROLLER (VLM-105/205) level. BASS and TREBLE CONTROLS make you adjusted equalizer - IMPORTANT NOTE : In case the priority function is activated, if you supply signal to MIC/LINE 2, then, all signals including LINE 4, 5, PAGING RINGER andmodule signals will be closed, set Jumper MS 2 on the FRONT PCB to "SLAVE". 2. Also, P.T.
VLA-120 C / VLA-240 C VARIO-LINE RÜCKSEITE 1. MIC PRIORITY SWITCH 1. MIC PRIORITY Schalter These are for priority setting switches for mic 1, 2, 3 to change priority ranking from No 3 to No 2, turn switch lever to the right. 3-fach Schalter um die Priorität der Mikrophoneingänge 1 bis 3 zu aktivieren. MIC 1 - 3 können separat auf "on" (Priorität) gestellt werden.
VARIO-LINE VLA-120 C / VLA-240 C 7. SPEAKER ZONES & ATT. OUTPUT 7. SPEAKER ZONES Pushing speaker zone selector (front panel NO.7), signal will be assigned to the selected zone. If all call switch, P.T.T microphone priority and zone selector of remote controller are activated, selected zone output outputare reseted to 100V/70V output. Ausgänge der 5 Lautsprecherkreise, einzeln einschaltbar und zu regeln in 6 Schritten (100V - 70V - 50V - 25V - 12,5V - 8,9V) oder über "ALL CALL" (100V).
VLA-120 C / VLA-240 C VARIO-LINE - PRIORITY FUNCTION - PRIORITÄTS FUNKTIONEN When shipped it is factory preset as follows pack signal priority switch (FRONT PCB SW305) : Setting at SLAVE. The following is priority ranking against all signal inputs of system and priority signal is "ON" "OFF" automatically. Werkseinstellung des Prioritätsschalters SW305 (hinter Modulleerfeldpaneel): "SLAVE". Die folgende Tabelle gibt alle möglichen Prioritäten wieder und ihre Rangfolge.
VARIO-LINE VLA-120 C / VLA-240 C Anwendungs und Einsatzmöglichkeiten - Beispiele 9
VLA-120 C / VLA-240 C VARIO-LINE Weitere Einsatzbeispiele * The above is for emergency situation like a fire. First, record alert voice message to the memory bank M6 in the DM-10A (Digital Massage). Second, select S/W MS802 PCB or RR-10 to „off“ position so as not to operate E/M message of VLM-205. This ist to prevent mistake from remote controller. 10 * Zur Fernsteuerung von „ALL CALL“ bzw. der Speicherbank 6 des DM-10A (Jumper MS 2 auf „Priorität“).
VARIO-LINE VLA-120 C / VLA-240 C Kaskadierung mit weiteren Verstärkern 1. TALK When pressing „TALK“ MIC signal is activated and make input of DC 24V from the crew terminal NO. 2 of main amplifier and priority is activated. 2. DIN JACK This consists of 7 pins use shield cable for microphone. 1. TALK Bei Bestätigung des Tastschalters 1 kann gesprochen werden, weiterhin wird der Vorgong und die Priorität aktiviert (wenn Schalter auf „ON“). 2. DIN-Buchse 7-pol.
VLA-120 C / VLA-240 C VARIO-LINE Remote Microphone VLM-105 Remote Microphone VLM-205 (identisch mit VLM-105, jedoch mit Fernbedienung für Digital Massage JDM-10A) 1. POWER (STATUS INDICATOR) 1. POWER Turn on the power, LED indicator lights. Diode zeigt Betriebsbereitschaft an 2. SEND (STATUS INDICATOR) In case data are supplied to amplifier, send LED indicator lights. 2. SEND Diode leuchtet, wenn Signale zum Verstärker gesendet werden. 3. BUSY 3.
VARIO-LINE VLA-120 C / VLA-240 C Technische Daten : Eingangsempfindlichkeit und Impedanz Ausgangsleistung Lautsprecherausgänge MIC / LINE 1 - 3 : -50dBu (2,45mV) 5k Ohm symm. bis -10dBu (245mV) 5k Ohm symm. LINE 4 - 5 : -10dBu (245mV) 15k Ohm unsymm. TEL PAGING : -10dBu (245mV) 5k Ohm symm. PACK UNIT : -10dBu (245mV) 10k Ohm unsymm. REC OUT : 0dBu (775mV) 3k Ohm unsymm. PRE OUT : 0dBu (775mV) 100 Ohm unsymm. AMP IN : 0dBu (775mV) 10k Ohm unsymm. VLA - 120 C : 120 W sinus (max.
VLA-120 C / VLA-240 C BLOCK DIAGRAM 14 VARIO-LINE
VARIO-LINE VLA-120 C / VLA-240 C NOTES 15
VLA-120 C / VLA-240 C VARIO-LINE Electromagnetic compatibility and low-voltage guidelines: RCS leaves all devices and products, which are subject to the CE guidelines by certified test laboratories test. By the fact it is guaranteed that you may sell our devices in Germany and in the European Union domestic market without additional checks.
