RCLander T-33 OPERATIONAL MANUAL
Please read before operating this system! W e would like thank you for purchasing our new product T-33, designed for the hobby enthusiast. Based on its full - scale counterpart, this USA Jet can undertake loops, inverted flight, rolls and other aerobatics easily. It is a highly maneuverable model aimed at the intermediate to expert pilot.
Specifications: Wing Span : 1683mm Length: 1520mm AUW: 3.7kg up EDF(Lander Metal DPS EDF): 90mm Power: 9S 4500mAh 25C or above Thrust: Up to 3.96kg Function: Flaps system-included Metal Electric retract & scale suspension struts included Gear doors system & Air-Brake (Option) ESC: 100A or above EDF SYSTEM LEDFDPS EDFDPS90 DPS9090-1A13/9 1A13/9 Main Accessories -3- Material: Aluminum Alloy, Metal special Weight: Ca. 538g(Motor included) Rotor: 90mm dia, 5-bladed.
Main Fuselage Front Lower Fuselage Both side of Inlet Parts Inside Ducting plate Parts Upper Rear Fuselage Lower Rear Fuselage Both Side Main Wing Set Horizontal Stabilizer Vertical Stabilizer Canopy 90 & 120 EDF Bay Parts Both Side Fuel Tanks -4-
Bombs& Missiles Parts PVC Wheel Cups parts PVC Air-Brake Set Plywood Block Set PVC Gear Doors Parts Remarks: 1) Operational Manual (included) 2) Extension cord x 7pcs & Y cord x 6pcs (included) except ARF version 3) Push rods for Elevator, Rudder, Aileron, Flaps, Air-Brake & Front Steering (included) 5) One plastic bag includes screws, Control Horns, Linkage Stoppers & related plywood block set.
Assembling the aircraft. For color images please go to www.rclander.com for download. 01 1) Take one extension cord to connect the nose electric retract first. 2) The nose electric retract has been pre-installed by factory before shipment. 02 1）Suggest to find one piece 70-130mm anti-slip foam plate (not included) for the battery compartment. 03 1) Using the strong double tape to fit on the anti-slip foam plate on the battery compartment as shown. Then put on the nose gear extension cord well. .
04 1) Use your Radio to gear down the nose gear first for preparation to glue up the front lower fuselage on the main fuselage. 05 1) Take enough epoxy to glue up the lower front fuselage on the main fuselage. 06 1) After finished the fixing of lower front fuselage, keep on the install the inside ducting plate. 2) Pls glue up the both side ducting plates together first.
07 1)According to the inside slot of main fuselage to take some epoxy to glue up the inside ducting plate set on the right position. 08 1) After glued up the inside ducting plate, pls cut out the cross foam bar as shown.
10 1) Inside the main fuselage is already pre set some slot for fitting both of two side inlet parts. 2) Kindly use the enough the epoxy and work carefully to install the inlet parts one by one as shown. It is because glue up area so longer. 11 1) Glue up both side inlet parts on the main fuselage should be one by one procedure.
13 1) Make sure the guiding inlet plate to be able fitted on the right position before glue up. Pls be reminded the shorter side is out & longer side is in side. 2) The installing method is put it from inside to outside. 14 1) After confirm the guiding inlet plate on the right position that can be used some epoxy to glue up as shown. 15 1) Prepare to install the horizontal & vertical stabilizer on the upper rear main fuselage. 2) Pls install the related servos before glue up action.
16 1) Pls use the cutter to open a small hole on the slot of the horizontal stabilizer for pass through rudder servo cable. 17 1) Pre-check the vertical stabilizer to be able well on the horizontal stabilizer slot before glue up action. 18 1) Use some epoxy to glue up the vertical stabilizer on the horizontal stabilizer. Pls make sure it able on the vertical degree.
19 1) Pre-check the whole set stabilizer can be well on the upper rear main fuselage and the rudder servo cable well pass through before glue up action. 20 1) Everything is correct then takes some epoxy to glue up as shown. 21 1) Prepare to install the main wing. Pls be noted the retract plug gear doors system and air-brake system are pre-installed by factory before shipment. 2) Pls prepare the related servos / extension cables and related pre-cut wood plates (included with the kit).
22 1) Gear down both side main gear first. 2) Glue up on side pre-cut wooden plate (shorter one) on one side maid wing (bottom) slot as shown. 23 1) Take enough epoxy to glue up both side main wings together. 2) Recommend to take some epoxy to fit up the gap or at lease on the upper of both of wooden plates for reinforcement purpose. 24 1) After finished the bottom side, turn around to install the upper side reinforcement wooden plated (included with the kit) on the middle main wing slots as shown.
25 1) Install the Aileron & Flaps servos on the main wing servos bay and use the extension cables to extend the cable pass through into the main fuselage. 2) Pls be reminded that the joiner position of extension must be fully put into the cable slot by cut out some foam for gaining the space if necessary. 26 1) All related servos cables included of Aileron/ Flaps and metal retract gear cable must be passed through under the metal retract to main fuselage.
28 1) Pre check the related wooden plate to be able on the right position or not before glue up. 29 1) Take some epoxy to glue up the wooden plate on the main fuselage as shown. 30 1) Take some epoxy or hot melt glue to fit on the steering servo on the main fuselage and link up the related push rod as shown.
31 1) Prepare to install the upper rear fuselage to the main fuselage. Pls be reminded to check up the four reinforcement carbon tube able connect the right position on the main fuselage and make sue whole set stabilizer on the right angle before glue up. 32 1) Take enough epoxy to glue the upper rear fuselage on the main fuselage. 33 1) After glued up action, take one y & one extension cable to link up both side elevator servos and one more extension cable for rudder servo.
34 1) Make sure the related extension cable on the right position then prepare to install the lower rear fuselage on the main fuselage. 35 1) Use some epoxy to glue up the lower rear fuselage on the main fuselage. Pls be reminded that the main rear edge wing bind nut wooden plate was pre-installed by factory. 36 1) Put in the pvc exhaust tube (included with the kit) on the EDF set as shown.
37 1) Take the metal edf mount (included with the kit) to lock up the EDF set on the bay and lock up the ESC on the wooden plate as shown. 2) Pls be reminded to check the EDF set space is fully enough installed your EDF set (specially other brand name edf set). Otherwise, you need to cut out some foam to gain the space or add some strong foam tape to fill up the gap before locked up by the metal mount. 38 1) Put on the foam edf cover with some double tape for fixing.
40 1) Install the other side elevator & rudder control horns and link up the push rods with servos. 41 1) Install both side main wings control horns of Aileron & flaps and link up the push rods with servos. Then cover the related servos by provided pvc pre-painted servos sheet. 42 1) Use the enough Y cables and extension cables to connect the aileron / flaps & air-brake servos and well bind up all cables then fix on the middle position in order to pass through main fuselage RX compartment easily.
43 1) Pass through all related cables from main wing into the main fuselage RX compartment before lock up the main wing on the fuselage. 44 1) Use the provided 4mm screws & wooded plates and washers to lock up the main wing on the fuselage as shown. 2) 4 x 40mm for front & rear position. 4 x 35mm for middle position. 45 1) Prepare to install both side fuel tanks parts /bombs & missiles.
46 1) Take some epoxy on the both side fuel tank pre set slot and put on both side main wing. Pls be reminded to make sure both side fuel tanks to be able fully insert on the main wing as shown. 47 1) Depend your request to install bombs & missile or not. Those must be used epoxy to glue up if you want to install. 48 1) Using some strong 4mm double tape to fix the canopy on the cockpit. Pls be reminded to fix the panel stick and pilots on the cockpit before fixing the canopy.
49 1) Competed canopy set. 50 1) Pls take the provided pre-cut pvc sheet to cover RX compartment closed to rear in order to reduce the air flow come from the front fuselage in order to let the nose gear door system well perform during the flight. 2) Link up all related servos cables with Receiver and bind up well. 51 1) Fully competed T-33A version and ready to fly.
- 23 -
Flight attention Do not fly at any place where another same-frequency model is being operated. Taking off: Always take off toward the wind. When launch T-33 by hands, maximize the power (include the micro-adjuster) and run several meters, then throw the T-33 horizontally. When launch T-33 on the ground, maximize the power and let T-33 accelerate in direction of the wind and keep it running straightly, after it run more than 60 feet, then pull the elevator joy stick, and it will take off.
