RLC2226
Important Safety Instructions and Maintenance Important Safety Instructions CAUTION Risk of electronic shock, do not open. Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. High Voltage Do not open To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
Important Safety Instructions and Maintenance Important Safety Instructions To avoid the fire, no naked flame source, such as lighted candles, should be placed on the apparatus. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
Important Safety Instructions and Maintenance Installation Do not place the set on an unstable cart, stand, table or shelf. The set may fall, causing serious personal injury as well as damage to the product. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Contents General description Specifications and accessories Overview Basic operation External connection Basic operation Trouble shooting Picture defects and countermeasures Basic operation 4 5 6 7 10 12 14 23 24
General description Feature: l Zero X radiation complies to green environment protection requirement l Auto tuning and fine tuning l One composite video input sockets (back) l One S-Video input socket l One PC VGA input socket l One YPbPr input socket l One HDMI input socket (HDMI 1.
Specifications and accessories Specifications: Description RLC2226 22 " Diagonal (max.) 1366X768 AC ~120V 60Hz 2WX2 50W Dimensions (LXWXH) TV with stand 530 X 209 X 393 mm TV without stand 530 X 77 X359 mm TV with stand 5.0 Kg TV without stand 4.6 Kg Accessories: l User’s manual l Remote control l Wall-mounted accessories: Two wall-mounted brackets, four fixed screws and four fixed sleeves.(Optional) Note: 1.
Overview 1. Power indicator 2. IR remote sensor 1. Power indicator Green: Normal playing status. Red: Standby status. 2. IR remote sensor Point remote control at this sensor to conduct remote control. 3. INPUT Press this button to display the selectable signal source for main source. 4. MENU Press this button to display OSD menu. 5. PROG / Press these two buttons to select channel or operate menu. 6. VOL / Press these two buttons to increase or decrease the volume or operate menu. 7.
Overview IN AV AUDIO OUT Audio out for external devices. AV VIDEO OUT Video out for external devices. 8 YPb/CbPr/Cr Connect to YPbPr/YCbCr video.
Overview Remote control Loading batteries: 1) Remove the lid of the battery compartment. 2) Insert 2 size AAA batteries with polarities as indicated inside the compartment. 3) Replace the lid. Note: 1) One loading of batteries will last 1 year under normal use. 2) If you don’t intend to use the remote control for a long period of time, remove them to avoid damage due to leakage. 3) Do not mix old and new batteries, or different types. 4) Don’t throw the batteries into fire or water.
Basic operation Remote control introduction 1.INPUT Select input source. 2.POWER Turn your TV on and off. 3.0~9 Use these keys to input digit, letters and special characters. 4.INFO Displays the program information. 5.RECALL To swap to the previous program you wanted from current program. 6.SOUND Select audio mode. Press the key repeatedly to choose one of the modes among Normal, News, Music, Preference. 7.PICTURE Select picture mode.
Basic operation (to be continued) 12.FREEZE No available for this model. 13.AV Swith to AV mode directly. 14.YPbPr Switch to YPbPr mode directly. 15.PC Switch to PC mode directly. 16.TV Switch to TV mode directly. 17.HDMI Switch to HDMI mode directly. 18. Press this button to shut off sound of the TV temporarily, press again to restore TV sound. 19.VOL q /p Press these buttons to adjust TV volume. 20.PROG q /p Press these buttons to change program upward or downward. 21.MENU Display the main menu. 22.
External connection Antenna connection Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be connected to the antenna jack directly, if the antenna cable is a 300ohm flat feeder cable, you need to use the 300ohm/75ohm converter (not included) to connect the antenna cable to the antenna jack. l 75Ωcoaxial cable is recommended to eliminate interference and double image due to the unmatched input impedance of the antenna.
External connection 2. How to assemble the stand? Before attaching/detaching the stand, make sure to turn off the TV. Before performing work spread cushioning over the base area to lay the LCD TV on. This will prevent it from being damaged. Assembling instruction: 1. Fix the stand and the Cabinet together with six screws (M4). (Figure 1) 2. Fasten the six screws used to secure the stand in place.(Figure 2) - To disconnect the stand from the TV, perform the above steps in reverse order.
Basic operation (to be continued) Turning the TV On and Off 1. Insert the power cord plug into a AC outlet, the TV will enter standby mode.Press POWER button on the remote control to turn it on . The indicator will switch from red to green. 2. If you want to stop watching TV or go out for a while, you can press POWER button on the remote control. If you want to watch TV again, you can press this button again. 3. Unplug the power cord when the TV will not be used for a long period time.
Basic operation (to be continued) 2) Press p /q Arrow button to enter the submenu and press t /u Arrow button to select the language you desire.
Basic operation (to be continued) 4) 5) SKIP Press q/p Arrow button to select “SKIP”, then press t/u Arrow button to select “On” or “Off”. On: skip the channel; Off: not skip. AFT Press q/p Arrow button to select “AFT”, then press t/u Arrow button to select “On” or “Off”.
Basic operation (to be continued) Adjusting the Picture Press MENU button on the remote control, then press t /u Arrowbutton to select “PICTURE” menu. PICTURE AUDIO PICTURE MODE SETTING FUNCTION BRIGHTNESS 50 CONTRAST COLOR 50 50 TINT 50 SHARPNESS BACKLIGHT COLOUR TEMP.
Basic operation (to be continued) Note: It is useless under no signal mode. Adjusting the Sound Press MENU button on the remote control, then press t /u Arrow button to select “AUDIO ” menu. PICTURE AUDIO SOUND MODE SETTING FUNCTION CHANNEL PREFERENCE EQUALIZER 50 BALANCE AVL OFF MONO MTS ADJUST 1) 2) 3) 4) 5) SELECT ME NU EXIT Adjusting Sound Mode Press q /p Arrow button to select “SOUND MODE”, use t /u Arrow button to adjust sound mode.
Basic operation (to be continued) 1) 2) 3) 4) OSD Language Press q/p Arrow button to select “LANGUAGE” and press t/u Arrow button to select language you desire. Adjusting SCREEN SAVER Press q /p Arrow button to select “SCREEN SAVER” and press t /u Arrow button to set screen saver. Adjusting OSD Position Press q/p Arrow button to select “OSD Position” and press t /u Arrow button to set position of OSD.
Basic operation (to be continued) 5) Parent Control In “Function” menu, press q/p Arrow button to select “Parent Control”,press t / u Arrow to enter the input password menu. Input the password to enter the submenu(the default password is 0000 and omnipotent password is 1980). PICTURE AUDIO SETTING FUNCTION CHANNEL CHANGE PASSWORD CHANNEL LOCK VIDEO LOCK OFF ADJUST SELECT EXIT ME NU (1) Change Password 1.Press q/p Arrow button to select "CHANGE PASSWORD" option. 2.
Basic operation (to be continued) l Channel Input 1.Press q/pArrow button to select "CHANNEL INPUT" function. 2.Input the channel number you want to lock and press OK key to confirm,the channel number will be add to the list below. 3.If you want to unlock a channel, press q/pArrow button to select the channel number in the list and press OK key to delete it. Note: You can lock 9 channels in "AIR" or "CABLE" source. l Clear All 1.Select a source you want to clear in "SOURCE" function. 2.
Basic operation (to be continued) 2.Window This TV supports no higher than 60Hz under PC mode, so please set the refresh rate of PC to 60Hz. If the frequency is higher than 60Hz, the screen may flicker. When the TV is in PC mode, press MENU button on the remote control. Press t/u Arrow button to select “WINDOW”.
Trouble shooting If you have any problem, check the countermeasure for each symptom listed below. The following symptoms may have caused by inappropriate adjustment rather than actual malfunction of the unit. If the trouble persists, contact the service center. Problem Possible Solution Poor picture and sound quality Try another channel. Adjust the antenna. Check all wire connections. No picture or sound under TV status Try another channel. Press the TV/AV button. Make sure the TV is plugged in.
Picture defects and countermeasures The most common types of television interference are as following: SNOWY PICTURE Snowy picture is usually caused due to weak signal. Adjust antenna or install an antenna amplifier. DOUBLE IMAGES OR “GHOSTS” Double images are usually caused by reflections from tall buildings. Adjust the direction of the antenna or raise it.
RLC2226
