User's Manual

ManualsBrandsRCA ManualsMisc ElectronicsRCA MST65BKR

1. Read these instructions before you begin. If

you are unsure of any part of the process, contact

a professional contractor or installer for assistance.

Improper installation can result in injury or damage.

2. The wall or mounting surface must be capable of

supporting the combined weight of the mount and

the display; if not, the structure must be reinforced.

3. Locate pipes, wires, or any other hazards in the wall

where you wish to install the mount before drilling.

4. Safety gear and proper tools must be used. Failure

to do so can result in injury or damage.

5. A minimum of two people are required for

installation. Do not attempt to install this mount

alone under any circumstances.

6. Follow all instructions and recommendations

regarding adequate ventilation and suitable

locations for mounting your display. Consult the

owner‘s manual for your particular display for more

information.

Warnings

CAUTION:

This wall mount is intended for use only with the

maximum weight of 75 kg (165 lbs). Use with heavier

than the maximum weights indicated may result in

instability causing possible injury.

Speciﬁ cations

Display Size: 37” to 65”

Maximum Load: 165 lb (75kg)

Mounting Pattern: 800 mm x 500 mm (31.5” x 19.7”) max

Tilt Range: 15° down

Proﬁ le: 1.4” (3.5 cm)

ﬂ at panel solutions

Tilt Wall Mount for LCD, Plasma, and

LED Displays

Instruction Manual

MST65BKR

Fits TVs 37”- 65”

Maximum Load

Capacity – 165 lb (75kg)

Continues on next page...

Pour des instructions

en français, se

reporter à la page 6.

Para obtener

instrucciones en

español, consulte la

página 11.

Box contents

Upper Wall Plate (x1)

Lower Wall Plate (x1)

Left Plastic Side (x1)

Right Plastic Side (x1)

Mount Arm (x2)

Instruction Manual (x1)

Hardware Kit (x1)

Template (x2)

Summary of content (5 pages)

PAGE 1
flat panel solutions Tilt Wall Mount for LCD, Plasma, and LED Displays MST65BKR Fits TVs 37”- 65” Maximum Load Capacity – 165 lb (75kg) Instruction Manual Specifications Display Size: 37” to 65” Maximum Load: 165 lb (75kg) Mounting Pattern: 800 mm x 500 mm (31.5” x 19.7”) max Tilt Range: 15° down Profile: 1.4” (3.
PAGE 2
Tools required Phillips-Head Screwdriver or Screw Gun Electric or Portable Drill 3 mm (1/8”) Drill Bit and Stud Finder for Drywall Installation 8 mm (5/16”) Masonry Bit for Concrete Installation Level Hardware kit (A) M6.
PAGE 3
5. Attach the wall plate to the wall using the M6.3 x 63 screws (A) and washers (B) English provided (see Fig. 3). Do not over-tighten these screws and do not release the mount until all screws are in place. Ensure that the mount remains level after all screws are secured. Fig.3 Part 1B – Mounting to the Wall (Concrete) IMPORTANT! For safety reasons, the concrete wall must be capable of supporting the combined weight of the mount and the display.
PAGE 4
3. Attach the mount arms to the back of your display using the screws identified in steps 1 and 2 (see Fig. 7): For displays with flat backs. For displays with curved or recessed backs. Fig.7 A. If you are using the M6 screws you will also need to use the M6 washers (H). M8 screws do not require washers. B. If you are using the longer screws on a display with a curved or recessed back, you may also need to use the spacers (I). Use one spacer or two spacers stacked as needed.
PAGE 5
Operation and adjustment 1. To change the tilt angle of your display, hold the display firmly in place and English loosen the tilt mechanisms using the long Allen key (J) from the hardware kit (see Fig. 10). Move your display to the desired position, and then re-tighten the tilt mechanisms. If your display is in the non-tilt position, you will need to push up gently on the display before you can move it. Do not release the display until both tilt mechanisms are firmly tightened. 2.