i
Recommended Tools Hex Drivers (1.5mm, 2mm, 2.5mm) Thread Lock Cross Wrench Long Nose Pliers Tips for Assembly Use good quality hex drivers to avoid stripping screw heads. Use thread lock when putting metal screws into metal parts. Note: Steps marked with an asterisk (*) require thread lock. Use thread lock sparingly. Do not over tighten screws otherwise you may strip the thread.
Warranty RC4WD non-electrical products are warranted to be free of defects in materials and workmanship when new. Our limited warranty does not cover damages due to normal wear and tear, user error of assembly or installation, user modifications, user's failure to perform routine maintenance, addition of aftermarket parts or option parts. This warranty lasts 30 days after arrival for original purchaser.
. s the iii RC4WD TF2 LWB RTR
shows c iv RC4WD TF2 LWB RTR
s v RC4WD TF2 LWB RTR
Items Shown: Z-R0009 XR3 3-Channel 2.4Ghz Transmitter/Receiver Radio Z-E0089 Outcry ll Waterproof ESC Z-E0035 Twister High Torque Metal Gear Digital Servo Z-E0004 540 Crawler Brushed Motor 45T Optional Parts: Z-R0008 XR3 2.4Ghz 4-Channel XR4 2.
RC4WD Outcry II Waterproof ESC BASIC SPECIFICATIONS Type Brushed Motor ESC Model Z-E0089 1/10 Electric ESC Specifications Lipo 2-3S 4-9 PCS NiMH (1.2V/PCS) BEC Output Voltage (V) - Current A Max Length (mm/in) ESC 5V/2A 45.40mm [1.79in] Max Height (mm/in) 24.70mm [0.97in] Max Width (mm/in) 33.60mm [1.32in] Output Current Continuous working current is 45A, Forward steps are 320A, Backward steps are 160A. Proper Motor 540 Motor Size/19T & Higher Winds 18mm [0.71in] 24.70mm [0.
INSTRUCTIONS Product Features and Characteristics I. NiMH/Lipo Option BATT BATT Lipo NiMH II. Drag Brake/Standard Option TYPE TYPE DRAG BRAKE STANDARD III. Micro Controller (MCU) Automatic Learning Center Point WARNING: Prior to proceeding, be sure to either remove the pinion from the motor or elevate the truck so the wheels are not able to touch the ground. 1. The CPU can automatically sense if it is at its center point.
3C Transmitter / Radio Step 1. Transmitter and Receiver Overview 2.4G ANT TH REV ST REV TH TRIM ST TRIM Connectors 1: Steering Servo (CH1) 2: Throttle Servo (CH2) 3: CH3 Servo (CH3) 4: CH4 Servo (CH4) B/C: Power Connector STEERING WHEEL TH EPA ST EPA POWER SWITCH 3CH EPA TRIGGER FAIL SAFE SET CHANNEL 3 SWITCH GRIP HANDLE D RC4W BATT BOX Step 3. Installing the Batteries Step 2. Receiver and Servo Connection (1) Remove the battery compartment cover. (2) Install four (4) new AA batteries.
3C Transmitter / Radio Step 5. Fail Safe Function Settings Step 4. Binding the Transmitter and Receiver 1. Turn on the receiver's power. Press the SW switch. The receiver’s LED should start flashing. 1. Set the TH, ST switches to the normal position. 2. Turn on the transmitter and receiver. 3. Press the F/S SET button, the LED on the receiver should start flashing rapidly. 4. Put the throttle trigger in the brake position, press the F/S SET button. The LED should become solid. 5.
All hardware should be taken from Bag C ●1* M3 x 6mm BHCS ●2* M3 x 8mm BHCS 1 RC4WD TF2 LWB RTR
3 4 2 RC4WD TF2 LWB RTR
3 RC4WD TF2 LWB RTR
4 RC4WD TF2 LWB RTR
5 RC4WD TF2 LWB RTR
BHCS 10mm 6 RC4WD TF2 LWB RTR
14 15* BHCS BHCS 7 RC4WD TF2 LWB RTR
1 6* M3 x 6mm FHCS ●1 M3 x 8mm FHCS 8 RC4WD TF2 LWB RTR
●1 ●1 -1 1 Optional (Not required) 2 Step 19-2 3 Step 27 9 RC4WD TF2 LWB RTR
M3 Drive haft Pin 10 RC4WD TF2 LWB RTR
Bearing BHCS 11 RC4WD TF2 LWB RTR
33 FHCS .
25 13 RC4WD TF2 LWB RTR
27 FHCS 28 BHCS 14 RC4WD TF2 LWB RTR
BHCS BHCS BHCS 15 RC4WD TF2 LWB RTR
16 RC4WD TF2 LWB RTR
mm BHCS 17 RC4WD TF2 LWB RTR
18 RC4WD TF2 LWB RTR
19 RC4WD TF2 LWB RTR
36 37 M3 Locknut M3 x 10mm BHCS M3 x 22mm BHCS 20 RC4WD TF2 LWB RTR
38 ● 9 M3 x 8mm BHCS M3 x 10mm BHCS 21 RC4WD TF2 LWB RTR
40 41 22 RC4WD TF2 LWB RTR
42 Wheel Disassembly Shown 23 RC4WD TF2 LWB RTR
4 2 M2X14mm SHCS 24 RC4WD TF2 LWB RTR
● 43 is not included ● 44 M3 x 8mm 25 RC4WD TF2 LWB RTR
Drive it like y built it! 26 RC4WD TF2 LWB RTR
Z-S0518 Soft Steel Leaf Springs Z-S1730 Z-R0009 Z-E0089 Z-E0035 Z-E0004 RC4WD Marlin Crawlers Side Plastic Sliders for TF2 LWB XR3 3-Channel 2.
28 RC4WD TF2 LWB RTR
100-0017
