/10 SCALE 4x4 TRUCK KIT
Recommended Tools Hex Drivers (1.5mm, 2mm, 2.5mm) Thread Lock Cross Wrench Long Nose Pliers Tips for Assembly Use good quality hex drivers to avoid stripping screw heads. Use thread lock when putting metal screws into metal parts. Note: Steps marked with an asterisk (*) require thread lock. Use thread lock sparingly. Do not over tighten screws otherwise you may strip the thread. ii RC4WD G2 rc4wd.
RC4WD Limited Warranty All RC4WD products are warranted to be free of defects in materials and workmanship when new. Our limited warranty does not cover damages due to normal wear and tear, user error of assembly or installation, user modifications, user's failure to perform routine maintenance, addition of aftermarket parts or option parts. This warranty lasts as long as the original purchaser owns the product.
All of the hardware should be taken from Bag E Parts can be found in Metal Parts Bag F 1* 2* 1 RC4WD G2 rc4wd.
3* 4* Plastic parts can be found in parts Bag G 5 2 RC4WD G2 rc4wd.
7* 3 RC4WD G2 rc4wd.
8* 9* 4 RC4WD G2 rc4wd.
10 * This step should be done on both frame rails 11 * 12 * 5 RC4WD G2 rc4wd.
13 * 14 * 6 RC4WD G2 rc4wd.
15 * 16 * 17 * 7 RC4WD G2 rc4wd.
18 * 8 RC4WD G2 rc4wd.
19 * 20 * 9 RC4WD G2 rc4wd.
21 * 22 * 10 RC4WD G2 rc4wd.
23 * 11 RC4WD G2 rc4wd.
24 * 25 * 12 RC4WD G2 rc4wd.
26 27 * 13 RC4WD G2 rc4wd.
28 * 29 14 RC4WD G2 rc4wd.
30 * 31 * 15 RC4WD G2 rc4wd.
32 * 33 * 16 RC4WD G2 rc4wd.
34 * 35 17 RC4WD G2 rc4wd.
36 * 37 Fit drive shaft rings 18 RC4WD G2 rc4wd.
38* Fit both front and rear drive shafts 39 * 19 RC4WD G2 rc4wd.
40 * 41 * 20 RC4WD G2 rc4wd.
42 * Note: Servo and servo horn are not included in this kit 21 RC4WD G2 rc4wd.
43 * 44 * 22 RC4WD G2 rc4wd.
45 Note: Wheels & tires may already be assembled in this kit so steps 45 – 50 may not be required but are included for future reference. Insert the ring inside the tire 23 RC4WD G2 rc4wd.
46 Place the rear wheel half inside the ring Ensure that the tire bead is evenly captured in the wheel rim. The tire may need to be pulled out a little to make it sit properly. 24 RC4WD G2 rc4wd.
47 Place the front wheel half inside the ring. Ensure that the wheel design is aligned front and rear. Ensure that the tire bead is evenly captured in the wheel rim. The tire may need to be pulled out a little to make it sit properly. 25 RC4WD G2 rc4wd.
48 Place the wheel hub on the rear of the wheel and insert a long bolt (M2.5 x 12mm) through the wheel Install a nut and tighten onto the long bolt. Make sure the tire bead is evenly captured while tightening the nut 26 RC4WD G2 rc4wd.
49 Install the second bolt (M2.5 x 8mm) and nut. Make sure the tire bead is evenly captured while tightening the nut 50 Fit all of the remaining bolts and nuts. Swap the long bolt that was fitted for the shorter bolt 27 RC4WD G2 rc4wd.
51 Fit all four wheels 52 28 RC4WD G2 rc4wd.
53 29 RC4WD G2 rc4wd.
Spare Parts Z-A0080 Yota2 Front Axle Z-A0081 Yota2 Rear Axle Z-S0790 G2 Body Mounts Z-S0791 G2 Servo Mounts Z-S0792 G2 Battery Deck Z-S0793 G2 Electronics Deck Z-S0794 G2 Front 3 Link + Panhard Mount Z-S0795 G2 Rear 4 Link Mount Z-C0040 G2 Chassis Set Z-U0027 G2 Tcase Mount Z-S0798 G2 Front Shock Hoops Z-S0799 G2 Rear Shock Hoops Z-S0800 G2 Front Bumper Z-S0801 G2 Rear Bumper Z-S0802 R3 Single Speed Mounts Z-U0028 R3 Single Speed Transmission Z-S0803 G2 Metal Drive Coupling Z-S0804 M3 Drive Shaft Pin Z-S080
Recommended Equipment Z-E0032 Twister High Performance Waterproof Servo Z-S0820 G2 24T Servo Horn Z-S0822 G2 25T Servo Horn Z-R0006 XR4 4-Channel 2.4Ghz Transmitter/Receiver Radio Optional Parts Z-S0734 1.9" 5 Lug Steel Wheel Hex Hub Z-S0532 1.9 5 Lug Steel Wheel Hex Hub with Brake Rotor Z-W0008 Land Rover Disco Freestyle 1.9" Wheels Z-W0037 Land Rover Disco Freestyle 1.
