Instructions for Use

15
CHARGE DES ACCUS AU LITHIUM EN MODE FAST CHARGE
CHARGE D’ACCUS AU LITHIUM EN MODE STOCKAGE
Le courant de charge diminue en n de charge, le processus à tension constante est raccourci an de terminer plus
vite la charge. En fait, la charge est interrompue quand le courant de charge atteint 1/5 du courant nominal, au lieu de
1/10 en mode normal. La capacité chargée est légèrement inférieure, mais le temps est réduit.
Vous pouvez régler le courant de charge et la tension de l’accu à charger.
Quand vous appuyez sur le bouton Star/Enter, la conrmation de la tension
s’afche. Ensuite, vous conrmez la tension et le courant.
Appuyez à nouveau sur Start/enter pour démarrer la charge.
Cet écran montre l’état de la charge rapide (FAST). Pour arrêter la charge à
tout moment, appuyez une fois sur Start/Enter.
Cette fonction est conçue pour les accus qui ne sont pas utilisés du tout pendant longtemps. Ce programme permet
de charger ou de décharger les accus jusqu’à un état spécique pour le stockage. Les accus sont classés par types :
3,75 V/élément pour les Lilo, 3,85 V/élément pour les LiPo et 3,3 V/élément pour les LiFe. Le programme commence
par décharger si l’état d’origine de l’accu dépasse le niveau de tension de stockage.
Sur cette page, vous pouvez régler le courant et la tension de l’accu. Une
charge ou une décharge amènera l’accu à la tension idéale pour le stockage.
Cette page afche l’état en temps réel durant la charge.
Appuyez une fois sur le bouton Batt Type/Stop pour interrompre les processus
de charge.
-
11
-
6.3 'FAST' charging Lithium battery
The charging current is getting smaller as the process goes to the near end term
of Lithium battery charging. To finish charging process earlier, this program eliminate
certain term of CV process. Actually, the charging current will goes to 1/5 from the
initial value to end the process while the normal chaging goes to 1/10 during CV term.
The charging capacity may be a bit smaller than normal charging but the process
time will be reduced.
You can set up the charging current and the voltage of
the battery pack is being charged. As you press Start/
Enter button the voltage confirmation will be displayed.
And then, if you confirm the voltage and current, press
Start/ Enter button again to start charging.
This shows the present state of 'FAST' charging. To
stop charging arbitrary, press Batt type/Stop key
once.
6.4 'STORAGE' control Lithium battery
This is for charging or discharging Lithium battery not to be used for the time
being. The program will determine to charge or discharge the battery to the certain
voltage depends on the voltage of the battery at its initial stage. They are different
from the type of the battery, 3.75V for Lilo, 3.85V for LiPo and 3.3V for LiFe per cell.
If the voltage of battery at its initial stage is over the voltage level to storage, the
program will start to discharge.
You can set up the current and the voltage of the
battery pack to be charged. The current will be used for
charge or discharge the battery to reach the ' storage '
level of voltage.
The screen shows the present situation during charge
process. To stop charging press Batt type/Stop key
once.
-
11
-
6.3 'FAST' charging Lithium battery
The charging current is getting smaller as the process goes to the near end term
of Lithium battery charging. To finish charging process earlier, this program eliminate
certain term of CV process. Actually, the charging current will goes to 1/5 from the
initial value to end the process while the normal chaging goes to 1/10 during CV term.
The charging capacity may be a bit smaller than normal charging but the process
time will be reduced.
You can set up the charging current and the voltage of
the battery pack is being charged. As you press Start/
Enter button the voltage confirmation will be displayed.
And then, if you confirm the voltage and current, press
Start/ Enter button again to start charging.
This shows the present state of 'FAST' charging. To
stop charging arbitrary, press Batt type/Stop key
once.
6.4 'STORAGE' control Lithium battery
This is for charging or discharging Lithium battery not to be used for the time
being. The program will determine to charge or discharge the battery to the certain
voltage depends on the voltage of the battery at its initial stage. They are different
from the type of the battery, 3.75V for Lilo, 3.85V for LiPo and 3.3V for LiFe per cell.
If the voltage of battery at its initial stage is over the voltage level to storage, the
program will start to discharge.
You can set up the current and the voltage of the
battery pack to be charged. The current will be used for
charge or discharge the battery to reach the ' storage '
level of voltage.
The screen shows the present situation during charge
process. To stop charging press Batt type/Stop key
once.