Three. Matter need attention about boot and pair 1,Before boot, please check if the gear switch is turn off or notworks sure be down} and IDLE switch is turn off or not {make sure any switch is turned off, iris non safety boot {display will flash [TH] or [IDLE] , RF no signal output), wait until alf be turn off. 2, Finish the code pairing with receiver within 1 min, if overtime, if will tweet be..be. Four. LCD function panel instruction [MODEL] : Planes choice.
Standard helicopter Delta wing Standard glider COP COPM~Flybatless Records management [NAME] 1.This page is for saving current configuration{all settings are using} to transmitter internal filch, truss a configuration opening from internal file.
put up thief ear> Picture? File ® Pictures 8 Open file Replete 8 4 How to save current configuration to specified file ape rats spats: a.Put up , the number shown in display is the internal file's file number Picture 10 b.Press up {o choose until to the specified file number. Picture 11 c.Press down to choose until to the specified file number d.Press
BET ee fe 1. Gyro sensitivity, set normal and stunt sensitivity. The function [ust valid fo the model hove gyro system: Note: T 2. Press despoilment, ants the menu. impressiveness} Pictures 17 3. Normal sensitivity adjust : Operate Step: a. to up position, display (NOR)MARK (Means normal sensitivity} Picture 18 a. adjust the normal sensitivity up b. Press( }, adjust the normal sensitivity down ©. Press{EXIT} to quit 4. stunt sensitivity adjustment, Operate step a.
2. Press (MENU) into it, press(+) or choose (EXP), after that enter this page. Picture 24 3. Operate Step: a. Harassment, choosy the number of the direction should be adjust { 1-aileron; 2-elevator; 4~ Rudder) b. Press up to adjust the ratio ©. down to adjust the ratio d. Press{EXIT), save and exit index curve Pictured Aileron ration McClure Elevator ratio Stricture Erratically Picture? This page used to adjust the normal throttle curve and stunt throttle curve.
5.Normal throttle curve throttle curve, Cloture throttle curve, forth point Postured throttle curve, ascend point throttle curve, fifth point Pictures throttle curve, third point Cloture Stunt throttle curve throttle curve, first point Cloture throttle curve, forth point Plurals throttle curve, second point Postural? throttle curve, fifth point Picture throttle curve, third point Pleasures Pitch curve [PII] 1. This page used to adjust the normal pitch curve and stunt pitch curve.
%. Normal pitch Pitch curve first point pitch curve, third point Clotures Pitch curve, second point Pleasures Postured Pitch curve forth point throttle curve, fifth poi Postured? Pictured Stunt pitch Pitch curve, first point Pitch curve, second point pith curve, third point Postured Picture Plethora Pitch curve, forth point throttle curve, fifth point Plotted Repleted ye nT] 1. This page used lo change single servo’s movement direction. £. it, choose{REV}, and then this page.
Ce Ga 1. This page used to check the firmware 2. Press{MENU) into it, choose Press {(MENU}o this gaps. Picture 3. Operate Step: a. display two bit byte on the right b. Press(}, display two bit buts on the left c. Put down the (left sari, in this way the character can auto rolling. d. Press EXIT to qui Hegel Ten Picture firmware interface 1. This page used to check the produce date 2. Press{MENU} into it, choose {DAT}, Press (MENU}o this page overproduce date interface Picture 57 3. Operate Step: a.
2. enter desktop key, (STD), Press{MENU} enter this page Pictured? 3. Operate Step: «. the focal point to adjust which item should be adjusted. Pictures? Show twinkle (STD), mean choose the standard mods Show Twinkies, mean choose train mode How Twinkies, mean choose student mods b. When show (MAS) during twinkle, you can input the series number of the student plane, be used match with ths student plans. Number column show 1, press input the first series number.
