User manual
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,
Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited. The operating instructions reect
the current technical specications at time of print.
© 2016 by CEI Conrad Electronic International (HK) Limited 89134RC_v1_0116_02_m_en_(8)
TRANSMISSION DISTANCES
The transmission distance is limited by the technology used for each link. Study below
diagram and observe the distances when operating the datalink.
10 m 1000 m
CHARGING THE BATTERY
Battery life: 3 hours
Charging duration: 1 hour
You may charge the battery while using the datalink.
1. Connect a regular micro USB cable to the micro USB port located on the right side of
the datalink.
2. Connect the USB-A connector to a USB power source (5 V/DC, 40 mA).
3. The indicator light Charge Status lights up red.
4. When the battery is fully charged the indicator light Charge Status lights up green.
5. Remove the USB cable.
OPERATION
Auto-off:
If the datalink is not connected to the mobile device within 5 minutes, it turns off
automatically.
Power on
When the datalink is turned off, press and hold the front button for approx. 3 seconds to
turn it on. The Bluetooth indicator light emits single blue ashes.
Power off
When the datalink is turned on, press and hold the front button for approx. 3 seconds to
turn it off. The datalink turns off automatically when not connected for at least 5 minutes.
Pairing
1. Make sure you have the latest version of the EYEControl app installed on your mobile
device and run the RC Logger rmware version FW2.0 or higher on your quadcopter.
2. When the datalink is turned off, press and hold the front button for approx. 6 seconds.
The Low Battery and Bluetooth indicator lights ash alternatively, indicating pairing
mode.
3. Enable Bluetooth on your mobile device and pair the datalink with the mobile device
through the app interface.
4. After approx. 30 seconds, the paired datalink and mobile device is indicated by blue
double ashes of the Bluetooth indicator light. In case of failed pairing, the Bluetooth
indicator light emits blue single ashes. Restart pairing procedure.
FUNCTION TEST
Make sure you test the following items outlined in the below table before take-off:
Test How
Charge status and low battery Turn the datalink on and refer to the table in
section “Indicator lights” on page 1.
Pairing Refer to paragraph “Pairing” on page 2.
Telemetry data and task points - Assign test task points to your quadcopter.
- Conrm reception of telemetry data.
CLEANING AND CARE
> The datalink does not require any maintenance, do not disassemble it. Maintenance or
repairs may be carried out by a professional only.
> Do not let liquid enter the datalink.
> Clean the exterior of the datalink using a clean, soft, dry cloth only.
> Do not use any aggressive cleaning agents or chemical solutions as these may
damage the housing causing discoloration and/or malfunction.
DISPOSAL
In order to preserve, protect and improve the quality of environment, protect
human health and utilise natural resources prudently and rationally, the user
should return unserviceable product to relevant facilities in accordance with
statutory regulations. The crossed-out wheeled bin indicates the product needs
to be disposed separately and not as municipal waste.
Consequently you comply with your legal obligations and contribute to environmental
protection!
PRODUCT SUPPORT
Visit http://www.rclogger.com/support or call +852 2559 2662 for product support.
Additionally visit our Online Ticket System at http://support.rclogger.com for any RC
Logger inquiry.
FCC COMPLIANCE STATEMENT
FCC ID: 2AARVRCL-Datalink
Statement according to FCC part 15.19
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
> This device may not cause harmful interference, and
> This device must accept any interference received, including interference that may
cause undesired operation.
Statement according to FCC part 15.21
Modications not expressly approved by this company could void the user’s authority to
operate the equipment.
TECHNICAL DATA
Battery ..............................LiPo 1S 40 mAh
Charging ...........................5V/DC via USB, 40 mA
Range ............................... Mobile device
Datalink: max. 10 m
Datalink Quadcopter (via transmitter): max. 1000 m
Bluetooth ..........................BLE4.0
Operating environment .....dry weather conditions
Operating temperature .....0 to 45 °C (+32 to +113 °F)
Storage temperature .........-10 to +45 °C (+14 to +113 °F)
Dimensions ....................... 49 x 32 x 14 mm
Weight ..............................approx. 15 g