Rebellion Electric Chopper Mini Electric Chopper TM Mini OWNERS MANUAL Read and understand this entire manual before riding! Item Numbers Mini Electric Chopper Black 15555-BK Red 15555-RD Orange 15555-OR Blue 15555-BL Rebellion Electric Chopper 15130760
CONTENTS Safety Warnings ............................................................ 1 Before You Begin ........................................................... 2 Assembly and Set-Up ................................................. 3-4 Repair and Maintenance ............................................. 4-7 Troubleshooting Guide.............................................. 9-10 Mini Electric Chopper Parts .................................... 11-12 Rebellion Electric Chopper Parts ....................
BEFORE YOU BEGIN Remove contents from box. Remove the foam separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the electric chopper was 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents.
ASSEMBLY AND SET-UP Charging the Battery Your electric chopper may not have a fully charged battery. Therefore it is a good idea to charge the battery prior to use. • Initial charge time: 12 hours • Run time: up to 40 minutes • Recharge time: up to 8 hours • Average battery life: 250 charge/discharge cycles depending on the level of depletion. WARNING: Always disconnect your electric chopper from the charger before cleaning with liquid.
ASSEMBLY AND SET-UP Attaching the Handlebars 1 Press the spring buttons on each side of the handlebars and tap the bars until the spring buttons slide inside and engage the corresponding holes in the fork. WARNING: Failing to properly engage the spring buttons that affix the handlebars to the forks can cause you to lose control and fall. 3 Tighten all four pinch clamp 2 When correctly engaged, the screws (two in the upper and two in the lower crown). handlebars will not disengage from the fork.
REPAIR AND MAINTENANCE ❑ Inflating the Tires Tires are inflated when shipped, but they invariably lose some pressure between the point of manufacturing and your purchase. Rear Tire WARNING: Failure to remove the valve adapter after inflating will cause the inner tube and/or adapter to be severed by the rear drive sprocket. Note: If you lose the adapter, a valve stem extender can be purchased at almost any auto parts store. 1 Use the special valve extender/ adapter supplied.
REPAIR AND MAINTENANCE WARNING: To avoid a pinch or injury, keep fingers away from moving sprockets and chain. 1 Loosen the rear axle by attach- ing wrenches to both axle nuts and loosening counter-clockwise. 2 Loosen the brake anchor screw 3 Tightening the adjusters clock- (attached with the small bolt in the long slot on the left side of the frame). wise tightens the chain; loosening the adjusters counter-clockwise will relax it.
REPAIR AND MAINTENANCE ❑ Chain and Tire Replacement – Rebellion Chopper 1 Loosen screw and remove chain guard. 2 3 Slide the wheel forward to Loosen the rear axle by attaching wrenches to both axle nuts and loosening counter-clockwise. slacken the chain and disengage the chain from the wheel sprocket and motor sprocket. Note: Your hands will get greasy doing this. 4 Remove wheel and replace chain or tire. To reinstall wheel, reverse these steps.
SB 1918 (CALIFORNIA) DECLARATION YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC VEHICLE. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Vehicle does not run Undercharged battery Charge the battery. A new battery should have been charged for at least 12 hours before using the vehicle for the first time and up to 8 hours after each subsequent use. Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and that the charger is plugged into the wall. Make sure power flow to the wall outlet is on.
TROUBLESHOOTING GUIDE Problem Possible Cause Solution Sometimes the vehicle Loose wires or connectors doesn’t run, but other times it does Motor or electrical switch damage Check all wires around the motors and all connectors to make sure they are tight. Charger gets warm during use No action required. This is normal for some chargers and is no cause for concern. If your charger does not get warm during use, it does not mean that it is not working properly.
MINI ELECTRIC CHOPPER PARTS Keep your Mini Electric Chopper running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar, drag-style 38. Screw, 6mm button head socket cap screw 2. Valve stem extender/inflator 39. Tank, tear-drop 3. Handlebar end cap, extender holder 40. Screw, 5mm button head socket cap screw 4. Grip, half length 41. U-bar 5. Speed control, twist grip 42.
MINI ELECTRIC CHOPPER PARTS 21 20 19 17 16 10 22 8 23 7 6 18 24 3 4 5 15 37 9 14 35 73 34 38 71 25 11 13 1 2 36 40 31 72 26 32 27 12 33 28 39 44 29 53 70 47 30 54 42 46 51 45 50 49 41 43 59 52 48 56 74 66 68 69 65 64 67 63 57 60 61 62 58 55 57A 12
REBELLION ELECTRIC CHOPPER PARTS Keep your Rebellion Electric Chopper running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. Front wheel, tire, tube, axle, nut 17. Chain 2. Front fender w/screws 18. Chain tensioner w/screws 3. Fork legs (2) with both clamps and screws 19. Sprocket, 66t and freewheel w/screws 4. Steering bolt assembly 20. Rear wheel, tire, tube, axle and nuts 5.
REBELLION ELECTRIC CHOPPER PARTS 1 2 3 31 4 4 4 6 6 13 30 12 7 14 29 9 10 8 11 13 28 14 15 26 27 18 24 25 16 23 19 17 20 21 22 14
SAFETY REMINDERS PRE-RIDE CHECKLIST ❑ Loose Parts ❑ Brake ❑ Frame, Fork and Handlebars There should not be any unusual rattles or sounds from loose parts or broken components. If you are not sure, ask an experienced mechanic to check. Check the brake for proper function. When you squeeze the lever, the brake should provide positive braking action. When you apply the brake with the speed control on, the brake cut-off switch will stop the motor.
