RAZORX DLX™ ELECTRIC SKATEBOARD NOTE: The product must be moving at least 3 mph (5 km/h) before motor will engage. Kick start product, with lever on remote in the “Go” position to engage motor. OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product.
CONTENTS Safety Warnings............................................................................................1-2 Before You Begin.............................................................................................. 3 Assembly and Set-Up....................................................................................4-5 Charging the Battery......................................................................................... 6 Pre-Ride Checklist..........................................
SAFETY WARNINGS Do not ride your product in wet or icy weather and never immerse in water, as the electrical and drive components could be damaged by water or create other possibly unsafe conditions. Never risk damaging surfaces, such as carpet or flooring, by use of a RazorX DLX Electric Skateboard indoors. PROPER RIDING ATTIRE Always wear proper protective equipment, such as an approved safety helmet (with chin strap securely buckled), elbow pads, kneepads and wrist guards.
BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches, or dents that may have occurred during shipping. Because the RazorX DLX Electric Skateboard was 99% assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES.
ASSEMBLY AND SET-UP Installing Remote Batteries Tool Required: Phillips Screwdriver 1 Loosen Phillips screw on battery cover and remove cover. 2 3 Install two (2) AAA batteries. Re-attach battery cover and securely tighten in place with screw. Remote Pairing Confirmation Note: Your remote should have been paired with your RazorX DLX Electric Skateboard at the factory. 1 Turn the power switch on the remote to the ON position.
ASSEMBLY AND SET-UP Pairing the Remote – Cont’d ON ON OFF OFF 3 Move the lever on the remote to the “STOP” position and HOLD. Do not let go of the lever. Turn the power switch on the remote to the ON position. 4 5 If the light on the power button on the product is solid red, your remote has been successfully paired. If the light on the product continues to flash quickly, turn power switch on the remote to the OFF position and repeat steps 3-4 until remote is paired.
CHARGING THE BATTERY Your RazorX DLX Electric Skateboard may not have a fully charged battery; therefore you must charge the battery prior to use. Be sure to charge the battery in a clean, dry location away from direct sunlight, flames or sparks. • Initial charge time: 5 hours. • Recharge time: up to 5 hours, even if the light turns green. Recommended maximum charging time is 24 hours. • Always charge the battery immediately after riding. • Fully charge battery before storing for extended periods of time.
USAGE How to Ride Do not activate the remote unless you are on the RazorX DLX Electric Skateboard and in a safe, outdoor environment suitable for riding. Turn power button to the “ON” position for both the RazorX DLX Electric Skateboard and the remote. Place one foot on the front of deck and with the other foot, push (kick start) RazorX DLX Electric Skateboard while holding the lever on the remote in the “GO” position. Place other foot on rear of deck once motor has engaged.
REPAIR AND MAINTENANCE Before beginning repair or maintenance: • Read the instructions • Disconnect charger • Turn the power button OFF • Exercise caution around exposed parts • Contact Razor Customer Service if unsure about any repair or maintenance Wheel Replacement Tool Required: 13 mm Socket Wrench 5-2 5-3 5-2 5-4 5-1 1 Using the 13 mm socket wrench loosen the locknut. 2 Remove the locknut, washer and wheel. 3 Insert replacement wheel, washer and locknut. 4 Tighten the locknut.
REPAIR AND MAINTENANCE Hub Motor Replacement – Cont’d 5 mm Allen Wrench 3 Using a 5 mm Allen wrench remove 4 Assemble the motor and tighten the screws. 5 Reconnect the motor connecting line and all 6 Tighten the screws on top of the board and the four (4) hex screws and take out the motor. the wires. Tighten the screws. secure the locknuts under the board.
REPAIR AND MAINTENANCE Remote Battery Replacement Tool Required: Phillips Screwdriver Note: AAA batteries are not covered under the limited warranty. 1 Loosen Phillips screw on battery cover and remove cover. Remove old batteries and properly dispose. 2 3 Install two (2) AAA replacement batteries. Re-attach battery cover and securely tighten in place with screw. Product Battery Replacement Tool Required: 4 mm Allen Wrench 1 Carefully turn product over.
REPAIR AND MAINTENANCE 3 Disconnect the battery connector from the control module. 4 Carefully remove battery. 5 Reinsert battery. WARNING: • Contains a lithium-ion battery pack - adult attention for changing and disposal. • Battery pack should only be replaced by an adult. • Dispose of batteries properly. See Page 11 – Battery Care and Disposal. • Battery pack should not be disassembled, crushed, punctured, opened or otherwise mutilated. 6 Re-connect the battery connector to the control module.
REPAIR AND MAINTENANCE Battery Care and Disposal • Do not store in freezing or below freezing temperatures. To properly maintain your battery and ensure maximum battery life, carefully read the “Charging the Battery” section on page 6 of this owner’s manual. • Battery pack should not be disassembled, crushed, punctured, opened or otherwise mutilated. CONTAINS LITHIUM-ION BATTERY PACK. BATTERIES MUST BE RECYCLED.
TROUBLESHOOTING GUIDE *Product(s) should be turned OFF and fully charged prior to doing any Troubleshooting. NOTE: All troubleshooting steps should be performed by an adult only. Problem Possible Cause Solution Does not work out of the box Product must be traveling at least 3 mph (5 km/h) before motor will engage Kick start to at least 3 mph (5 km/h) while the lever on the remote is in the “GO” position to engage motor. Product not paired with remote Refer to page 4-5 for pairing information.
RAZORX DLX ELECTRIC SKATEBOARD PARTS Keep your RazorX DLX Electric Skateboard running for years with genuine Razor parts. Visit our website or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. 2. 3. 4. 5. Remote Control Module Case Cover Battery Battery Cover ON/OFF Button 6. 7. 8. 9. 10.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
