ELECTRIC HUB MOTOR SCOOTER NOTE: The unit must be traveling at least 3 mph (5 km/h) before motor will engage. Kick start to at least 3 mph (5 km/h) while applying throttle to engage motor. OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product.
CONTENTS Safety Warnings............................................................................................... 1 Before You Begin.............................................................................................. 2 Assembly and Set-Up....................................................................................... 3 Charging the Battery and Pre-Ride Checklist................................................... 4 Usage and Repair and Maintenance.......................................
BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES.
ASSEMBLY AND SET-UP Attaching the Handlebars WARNING: Do not attempt to thread the stem into the front fork thread. Tool Required: 5 mm Allen Wrench Note: Make sure any cables/wires are out of the way before inserting the stem into the fork. WARNING: Failure to properly tighten the collar clamp may allow the handlebars to dislodge while riding and may cause you to lose control and fall.
CHARGING THE BATTERY Your electric scooter may not have a fully charged battery; therefore you must charge the battery prior to use. • Initial charge time: 12 hours. • Recharge time: up to 12 hours, even if the light turns green. Recommended maximum charging time is 24 hours. • Always charge the battery immediately after riding. • Fully charge battery before storing for extended periods of time. • Unplug charger from the wall outlet when not in use.
USAGE q Starting the Scooter Turn power “ON”; put kickstand up and place both hands on the handlebars. Place one foot on deck plate and with the other foot, push (kick start) scooter while twisting throttle. Place other foot on deck plate once motor has engaged. q Stopping the Scooter Note: Electric scooter must be moving at least 3 mph (5 km/h) while engaging throttle to engage motor.
REPAIR AND MAINTENANCE q Front Tire Replacement Note: Front wheel hardware sequence Tools Required: Two (2) 5 mm Allen Wrenches Right Side 8-2 Spacer Fork 8-1 Coupling Bolt Left Side 8-2 Spacer 8-2 8-1 8-2 8-3 Fork 8-3 Bolt 1 Using two (2) 5 mm Allen wrenches, loosen the axle bolt. Remove wheel and install replacement wheel.
REPAIR AND MAINTENANCE q Rear Wheel/Hub Motor/Battery Replacement Cont’d Tools Required: Phillips Screwdriver and Two (2) 13 mm Wrenches Note: When re-inserting the motor wires into the connector, make sure the red wire connects to the yellow wire and the black wire connects to the blue wire. Red Black Note: Motor Red Black 5 Using a pointed object carefully depress the tabs on the metal pins inside of the motor wire connector and remove the wires. Carefully pull wires out from battery tray.
TROUBLESHOOTING GUIDE *Product(s) should be turned OFF and fully charged prior to doing any Troubleshooting. NOTE: All troubleshooting steps should be performed by an adult only. Problem Possible Cause Solution Does not work out of the box Product must be traveling at least 3 mph (5 km/h) before motor will engage Kick start to at least 3 mph (5 km/h) while twisting throttle to engage motor. Loose connection(s) Check for loose connections/wires underneath the deck plate.
POWER CORE E100 ELECTRIC SCOOTER PARTS Keep your scooter running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 1. 2. 3. 4. 5. 6. 7. 8. Tube Plug Handlebar Grips (Right/Left) Single Speed Twist Grip Throttle Handlebar Stem Brake Lever Assembly Battery 24V (2 12V)/6A Collar Clamp Headset (Upper/Lower) 1 2 3 9. 10. 11. 12. 13. 14. 15. 16.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
