NOTE: The unit must be traveling at least 3 mph (5 km/h) before motor will engage. Kick start to at least 3 mph (5 km/h) while applying the throttle to engage motor. OWNER’S MANUAL Read and understand this entire manual before allowing child to use this product! For assistance contact Razor. DO NOT RETURN TO STORE. NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect exact appearance of actual product. Specifications subject to change without notice.
CONTENTS Safety Warnings............................................................................................... 1 Before You Begin.............................................................................................. 2 Assembly and Set-Up....................................................................................... 3 Charging the Battery......................................................................................... 4 Pre-Ride Checklist......................................
BEFORE YOU BEGIN Remove contents from box. Remove the separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY ASSEMBLY OR MAINTENANCE PROCEDURES.
ASSEMBLY AND SET-UP Attaching the Handlebars Note: Make sure all the cables/ wires are out of the way before attaching the handlebars onto the fork. Tool Required: 5 mm Allen Wrench WARNING: Failure to properly tighten the collar clamp may allow the handlebars to dislodge while riding and may cause you to lose control and fall. When correctly tightened, the handlebars will not rotate out of alignment with the front wheel under normal circumstances.
CHARGING THE BATTERY Your electric scooter may not have a fully charged battery; therefore you must charge the battery prior to use. • Initial charge time: 12 hours. • Recharge time: up to 12 hours, even if the light turns green. Recommended maximum charging time is 24 hours. • Always charge the battery immediately after riding. • Fully charge battery before storing for extended periods of time. • Unplug charger from the wall outlet when not in use.
PRE-RIDE CHECKLIST Brake Safety Gear Check the brakes for proper function. When you squeeze the lever, the brake should provide positive braking action. Make sure that the brake is not rubbing when the lever is released. Always wear proper protective gear, such as an approved safety helmet. Elbow pads and kneepads are recommended. Always wear athletic shoes (lace-up shoes with rubber soles) and keep shoelaces tied and out of the way of the wheels, motor and drive system.
REPAIR AND MAINTENANCE Turn power switch “OFF” before beginning repair or maintenance: • Read the instructions • Remove charger plug • Turn the power switch off • Secure the unit under repair • Exercise caution around exposed parts • Contact Razor customer service if unsure about any repair or maintenance Adjusting the Brakes Tool Required: 10 mm Wrench B A 1 To adjust brake cable play, thread the brake lever adjuster in or out 1/4 to 1/2 turn until the desired brake adjustment is attained.
REPAIR AND MAINTENANCE Note: Rear wheel hardware sequence Replacing the Chain and Rear Wheel (Continued) 18-1 18-2 18-3 18-4 18-5 18-7 4 Remove wheel and install replacement wheel. (Note the sequence of the hardware.) 5 Push the chain tensioner 6 With two (2) 13 mm wrenches, down to install the chain on both sprockets. re-tighten the locknuts.
TROUBLESHOOTING GUIDE *Unit(s) should be turned off and fully charged prior to doing any Troubleshooting NOTE: All troubleshooting steps should be performed by an adult only Problem Possible Cause Solution Does not work out of the box Unit must be traveling at least 3 mph (5 km/h) before motor will engage. Kick start to at least 3 mph (5 km/h) while twisting throttle to engage motor. Loose connection(s). Check for loose connections/wires underneath the deck plate.
ELECTRIC SCOOTER PARTS Keep your scooter running for years with genuine Razor parts. Visit our website for more information on spare part availability. (Specifications subject to change without notice.) 1. Handlebar grips (right/left) 2. Single speed twist-grip throttle 2-1 Sleeve 3. Handlebar stem 4. Brake lever assembly 5. Collar clamp 6. Headset (upper/lower) 7. Front caliper brake with brake pads 8. Front fork with limiter 9. Front wheel complete (See page 6 for hardware sequence) 10. Battery tray 11.
NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.
FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
