Installation Manual Part 7

FCC ID: CDG-ARTU EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.3.3.3 C-2000 MMT Handset Test Menu
The MMT Handset Test menu screen is shown in Figure 9.3.33.
Menu selections are as follows:
A brief description of the Handset Test
+ vt. OA .-r aadio ..~ +
, ,
I f
f f
, f
f ,
I ,
+ +
+ r ~U ~O8Pt +
: C-2000 -.r BA88ft - - :
, ,
I ,
: 1 - BaD48.t -.tea Call P.-ogre.. 7-.. :
: 2 - 884io Qe-~.te4 Call P.-ogre.. -. :
: 3 - ..tabli.h 8aD4..t LA8 :
: t - t Baa48.t Att~ibat.. :
: 5 - t ..iat--. AGO... pm :
: :
: 8Dt.~ 7e.t ..l.ctioa (1 - 5. 8ac to exit 88Du) I - :
.
.
:
0
0
Figure 9.3.3.3. The MMT Handset Test Menu Screen.
1) Handset Generated Call Progress Tones - This command will cause a Handset to generate one of several
call progress tone available as a feature of the Handset. These tones included: No Tone, Fast
Busy, Bong, Out-Of-Range, and Audible Call Alert. It should be noted that the Handset number
refers to Handset LAN address and not to the interphone number.
2 - Radio Generated Call Progress Tones - This command will cause the ARTU to generate one of several
call progress tone available. These tones included: No Tone, Dial Tone, Busy Tone, Ringback
Tone, and Call Waiting Tone. It should be noted that the Handset number refers to Handset LAN
address and not to the interphone number.
3 - Establish Handset LAN - This command is used to determine that the high speed data distribution bus
(or LAN) is in sync with devices connected to the ARTU. It will also report the number of
Handsets and repeater devices connected to the LAN. It should be noted that this test treats all
repeater devices the same, i.e. CDBRs and AIUs. Also, a CAS will not be reported with this test.
This test takes fifteen second to complete and display infonnation in the Radio Responses
window. Figure 4.3.3.2 shows the MMT Radio Response window after performing the Handset
LAN test.
4 - Reset Handset Attributes - This command will reset programmable attributes of the Handset to factory
default values. It should be noted that this command will change values of Speaker Gain, Call
Alerter Gain, Sidetone Gain, and DTMF Gain.
5 - Reset Maintenance Access Passcode - The Maintenance Access Passcode is required to establish a
Maintenance Session which will allow access to the Handset programmable features of the C-2000
system. Resetting the Maintenance Access Passcode will set the Passcode to the factory default
value of 0000.
+ T &84io "8PQD8' +
I .
I .
: - 78.t. 8rrABLI8B -- LU "_lt8' PUS :
: 78 %a ~ :
: 3 8a11488t. A88ig-a I
: 2 cmaa pze_t :
: C-2000 report.8 _i-iDV t...t. ~8B _87 ~ ped0C8e4. I
I .
1 .
+ +
Figure 9.3.3.3.2. The MMT Radio Responses Window For The Handset LAN Tell
9-29 RevB