Installation Manual Part 7

FCC ill: CDG-ARTU EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
'--V'.OA.-r Radio ..~ +
. I
I I
I I
I I
. I
I I
+ +
+ r 8aDD ~ +
: C-2000 -.r .- -- ~~~~ - :
I I
I I
: bur - - fil- into the queue . ~.~ . :
: bt.r P%L B8X file to a-l0a4 f~ C:\~ (88C to q8it): ~.B8X :
I .
I .
: bter - Di_.tic an fil- into tba QU"'. . -~.~ . :
: bter P%L8DD.8D file to a-l0a4 f~ C:\~ (88C to QUit): ~.B8X :
I I
I I
: bter - appliceti- fil- tatoo tM QU"'. . U'fCc-.~ . :
: 8ater P%L B8X file to a-l0a4 f~ C:\~ (8- to QUit): ~.B8X :
I I
I I
: ...ter - »8. fil.- into the QU"'. . .u..c-.B8X . :
: ...ter P%L B8X file to a-l0a4 f~ C:\~ (88C to QUit): _pc.-.B8X :
Figure 9.3.1.2. The MMTI Batch Software Download Menu Screen
9.3.2 MMTI Commanded Mode - C-2000 MMT Radio Configuration Menu
The Radio Configuration menu is used to access ARTU databases and the Status screens. The MMT Radio
Configuration menu screen is shown in Figure 9.3.2.1. The ARTU must be in a "Locked Offline State"
when using these commands. See the Radio/lnstallation menu for the information on state changes. A
brief description of each of the Radio Configuration menu selections is provided as follows:
~--~-~"~~~ V,.OA .-r Radio "8POD ., C,
, ; ',,': 0':,'
I
I
+ + -. ~ : C-2000 - aADZO ~_7ZC8 ~
I
I
: 1 - Lo84 8pee4-Dial Databa-
: 2 - sa.. apee4-Dial Databa-
: 3 - vi- Z_tO&'Y Databa..
: . - ~ Paut COIIDt.8~.
: 5 - 8DAbl./Di.abl. 8t.tU8 ap4at..
: , - 8DAbl./Di.abl. n 8CL -
, ,
: 8Dt- a84io C-'ipratiOG _l8CtiOG (1 - I. -- ~ ~t -). - i
. I
. I
, I
. I
I
,
.
~ .
~ ~ +
Figure 9.3.2.
The MMT Radio Configuration Menu Screen.
I) Load Speed-Dial Database - This command will load speed-dial database information from a file stored
on the computer into the ARTU memory. The numerical portion of the filename root must match
the numerical version number of the ARTC C-2000 software when loading the speed dial
database. See Save Speed-Dial Database. If the numerical portion of the filename root does not
match the numerical version number of the ARTC software, then a DOS command which
modifies the filename will need to be performed.
2) Save Speed-Dial Database - This command will save the speed-dial database information stored in the
ARTU to a file on the computer. The user must provide a root for the filename in which the
information is to be store in the computer memory. The numerical portion filename root will
automatically be tagged with the version number of the ARTC C-2000 software when using this
command.
3) View Inventory Database - This command will display ARTU database the following information: the
ARTU electronic serial number, operational minutes and software subroutine version numbers.
9-23 RevB