Installation Manual Part 7
FCC ID: CDG-ARTU EXHIBIT C
MAGNAST AR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
9.3.1 MMTI Commanded Mode - C-2000 MMT Boot Menu
The MMTI Boot menu is used to perfonn functions while the ARTU software in not executing. This
includes reviewing software versions, loading new software files and starting software execution. The
MMTI Boot menu screen is shown in figure 9.3. I. I A brief description of each of the Boot menu
selections is provided as follows:
I} Start Radio Software - This command will start Built-In-Test (BIT) and radio software execution. The
radio software must be executing before any of the menu options, other that the boot menu
options, are valid.
2} Report Radio Software Filenames - This command will report the software files that are loaded in the
ARTU. The software files will be reported similar to those shown in the Radio Response window
of Figure 9.3.1.1.
3} Initiate Boot - This command will stop radio software execution and place the radio in a Boot mode of
operation. The ARTU must be in a Boot mode of operation for commands on this screen to be
valid.
4} Load Radio Software - This command is to be used when new software is to be loaded in the ARTU.
This command can only load a single file at a time and is only valid for ARTC and MDSP code.
5} Batch Load Radio Software - This command is to be used to load all four different software files
required to operate the ARTU at one time. See Figure 9.3.1.2 for an example of the Batch
Software Download screen
6} Start MMT Tutorial- This command can be used to start the installation mode of the MMTI.
7} Configure MMT COM Port - This command is used to change the data transfer (baud) rate when
loading software between the MMTI computer and the ARTU. It should be noted that after
completion of a file transfer the baud rate must be set back to 9600 in order for the MMTI
software to communicate with the ARTU.
8} Configure Batch Download Baud Rate - This command is used to change the data transfer (baud) rate
between the MMTI computer and the ARTU when batch software downloading is to be
performed. The default baud rate value is 9600 (9.6 kbs) for batch software downloading. This
command allows the baud rate to be change to either 19.8 or 38.4 kbs It should be noted that after
completion of a file transfer the baud rate will automatically be set back to 9600 in order for the
MMTI software to communicate with the ARTU.
+ V6.0A -.r aadio "~e +
. .
. .
: ~~-ap .~a~.o 10376 .ic~oproce.8Or OK. SRA8 OK. :
: Aa~ coda rile ~60..B8X V~ 0.0 Da~e 0./06/00 ~.025 8aDk 6 c.cotc..:
: DS. coda rile 8D8.c.OA.B8X V~ 0.0 Date 03/27/00 12013 8aDk 2 c.c012'1:
: .r~ coda Pile ..r~.OA.B8X V~ 0.0 Da~e 05/11/" 16.03 8aDk 1 c.c.20'C:
: - coda rile --.~31C.B8X V~ 0.0 Date 0./2./'6 ~..27 8aDk 1 c.c.-:
: 88410 .of~ i. DOt -_t1ng.
+ +
+ -.. ~e +
: C-2000 - BOO!' - :
I .
. .
: 1 - start. b4io 8oftware :
: 2 - ~ Radio SOft-- ril_. :
: 3 - rDi~iat.e - :
: . - LO84 aadio SOf~ :
: 5 - Ba~cb LO84 b4io SOf~ :
: 6 - start. - fttorial :
: 7 - c~igure - ~ .~ :
: 1 - c~igure Batcb ~~ ..a4 aate :
: :
:8Dterc~(1-5.Qtoquit_).- :
. I
. I
. I
. .
+ +
The MMTI Boot Menu Screen
Figure 9.3.
Rev 8
Q.22