Installation Manual Part 6

FCC 10: CDG-ARTU EXHIBIT C
MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM
+ V4. OA NNT Radio Response +
I I
I I
: Power-up Statu8, 80376 Kicroproc...or OK. SRAH ox. :
: ARTC code Pile ARTCC4OB.HIX Ver 0.0 Date 04/06/00 14,25 BaDk 1 CRC,~:
: DSP code Pile KDSPC40A.HIX Ver 0.0 Date 03/27/00 12,13 BaDk 2 CRC,1298:
: BIT code pile MBITC40A.HIX Ver 0.0 Date 05/18/99 16,03 BaDk 1 CRC,209C:
: Boot code Pile ~31C.HBX Ver 0.0 Date 04/24/'6 14,27 BaDk 1 CRC,B8& :
: Radio sottware is not executing.
+ +
+ V1A NNT Tutorial +
: IJfS1A104 1
: This test step is info~tional only. :
: Pressing .C' will start Built-In-Test (BIT). The no~l BIT process begina 1
: by turning .(»t. the ARro pault indicator. The ~ will indicate in that the :
: AR'1'U baa started sott~e execution which is displayed in the Radio :
: Respon... window. The AR'1'U then begins an PBPftCIf test which takes :
: approximately 15-20 seconds. During this time there will be no new ..ssages :
: di8Played in the Radio Responses window. BIT test result into~tion will:
: be reported in the Radio Responses window. Depending on how long the ARTU :
: baa been powered prior to executing power-up BIT. the screen may paU8e in :
: the middle ot the tests. This paU8e is to allow the ARTU 08cillator to :
: _ra-up. This can take one to five IBinutes. After this paU8e. BIT will :
: complete. :
: (R)eturn, - :
+ +
Figure 9.l.3.A. Start ARTU Operational Software MMTI Troubleshoot Screen.
V4. OA MMT Radio Responses
: WAITDfG FOR POWER-UP BIT RESULTS «5 IIIMnE DELAY:
: Press 'B8c' to Terminate Wait
: Radio software starting execution.
: The KIlT baa been reconfigured for CON Port 1 at 9.6 kbs.
'IR
S'.'O S c ;' f'
, ,C',
: S~t_: Radio ~SP0D8es window does not change. ';;';;~
: al Did you W8~t for the PZPROM test to cO8plete. if 80 Pr88s "R" for,:,~
: rete.t. "};
: bl Did the ARro fault light illlainate? cf
: Sy8ptoa: ARro fails power-up BIT. :
: al Determine the Brr fault and record for repair information. See :
: KagnaStar Inatallation Manual for steps required to view fault :
: information. Replace faulted ARTU. :
: Symptom: ARro appears to pause during Brr for l~ger than ten ainutes. :
: al If the BIT testing stops at the "TEST AKX" test step for longer than :
: ten ainute. at ro- t~rature then note that the ARTU baa failed :
: OCXO ~-up. Replace the failed ARTU. :
: (Rleturn: - I
+ +
Figure 9.1.3.8. Start ARTU Operational Software MMTI Troubleshoot Screen.
9-4 RevB