Installation Manual Part 5

ManualsBrandsRaytheon IIS ManualsElectronicsAir-Ground Radio System

EXHIBrrc

C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM

FCC ID: COO-ARTU

MAGNASTAR

7.1.2.7.1 Handset Alerter and RJ-ll Gain Settings

The Handset Alerter gain setting sets the audio level for the handset ringer on C-2000 digital handsets. The handset speaker

provides the ringer output. The Handset Alerter gain can be adjusted between 0 to 31. The default value is 27. There is very

little discernible audio level difference between 27 and 31.

Select +

for more

-->

Select the appropriate

number to change the gain

settings.

Gains

Handset 27

Alerter

(+) ->1

(-) ->7

->3

->9

RJ-l

Select + to reach other

Handset Attribute screens

More --->..

Go BAck >1

7.1.2.7.2 Auxiliary Call Alerter and Auxiliary Call Alerter Cadenee

Each active port can be configured to activate any combination of the ten output switches of the Call Almer Switch (CAS)

when the port is called. The CAS configuration is station dependent and must be programmed for each individual active port.

When an aux.iliary call aImer is selected from the maintenance screen, it will activate the associated output oftbe CAS. The

output will stay active until another screen is selected. The current aux.iliary call alerter output values will be highlighted on

the maintenance screen. Note that if CAS 0 is configured as a service availability indicator or if CAS 9 is configured as a call

in progress indicator, CAS 0 and CAS 9 (respectively) will not appear on either the Call Almer or Cadence menus shown in

this section.

There are two different cadence patterns in which the CAS outputs can be configured. They are either one second "on"

followed by three seconds of "off' to simulate a ring, or continuous "on". Each of the ten individual outputs can be

configured for either one of the types of cadence. The cadence is a system function and need only be programmed from one

handset. The cadence handset maintenance screen will display the current setting values. A highlighted number corresponds

to a simulated ring with a one second "on" followed by a three second "off'. The output will activate when selected

(assuming the output is also selected in the auxiliary call alerter screen) and will stay active until another screen is selected.

Auxiliary-

Call

Alerter

Cadence

Select the appropriate

number(s) of the Auxiliary

Call Alerter required.

Select the appropriate

number(s) to change the

Cadence of the CAS

output.

Auxiliary

Call

Alerter(s)

>1 >2 >3

>4 >5 >6

>7 >8 >9

J~.~, >o"{i

Press the number again to

deselect an output.

>1>2 >3

>4 >5 >6

>7 >8~9

Press * to view the

Cadence screen. -->

Cadence >*

More --->+

Go Back >1

Press + to reach other

handset attribute screens

Go Back >1

RevS

7-19

Summary of content (8 pages)

PAGE 1
EXHIBrrc FCC ID: COO-ARTU C-2000 DIGITAL AIRBORNE MAGNASTAR TELEPHONE SYSTEM 7.1.2.7.1 Handset Alerter and RJ-ll Gain Settings The Handset Alerter gain setting sets the audio level for the handsetringer on C-2000 digital handsets. The handsetspeaker provides the ringer output. The Handset Alerter gain can be adjusted between 0 to 31. The default value is 27. There is very little discernible audio level difference between 27 and 31.
PAGE 2
EXHIBrrc FCC 10: CDG-ARTU MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 7.1.2.7.3 Speaker Gain: The alJdjo level of the earpiece on a digital handsetcan be changedwith the speakergains screen. The range of val~ for the coarse speakergain is from 0 to 31. Values greater than 24 may causethe receive audio quality to degradeand become distorted. For this reasonvalues above 24 are not recommended. Values in the range of 19 to 24 are normal for most aircraft.
PAGE 3
EXHIBIT C FCC ID: CDG-ARTU MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 7.1.2.7.5 Sidetone Gains Audio that is fed from the microphone to the earpiece speakeris called sidetooe. The value of the sidetone audio can be adjusted. The default value for voice sidetone is 13 and DTMF is 70. Values higher than these are not recommended. They may be found to be too loud and uncomfortable for the user.
PAGE 4
FCC 10: CDG-ARTU EXHIBIT C MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 7.1.2.7.7 MicrophoneTXGain It is possible to adjust the microphone audio gain. Becausethe digital handsetincorporates a noise canceling microphone, changing the microphone gain level can significantly degnide the sound quality and therefore it is not recommendedthat the microphone gain level be adjusted. The microphone gain level does not have a standard default value and therefore is adjusted individually at the factory.
PAGE 5
EXHIBffC FCC 10: CDG-ARTU MAGNASTAR C-2000 DIGITAL AI RBORNE TELEPHONE SYSTEM 7.1.2.8Airall Sereeas The aircall screensare used to enter personal aircall numbers, retrieve stored aircall messagesfrom memory, review programmed aircall and SATCOM terminal ID's. 7.1.1.8.
PAGE 6
EXHIBrrc FCC ill: CDG-ARTU MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM It is possible to view Aircall and SATCOM TenninallD numbers programmed in the maintenancesetup screens. Aircall and SATCOM TenninaliD numbers stored as station type can also be viewed from the Services screenon a digital handset. Ajrcall and SATCOM T enninallD numbers programmed as aircraft type can only be viewed using the following screen progressions. Select 8 to view aircall screens.
PAGE 7
EXHIBITC FCC 10: CDG-ARTU MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM 7.1.2.9 Remote Station Programming Remote station programming is used to program CDBR-2 analog interface ports. Equip~nt connectedto theseports do not have LCD display capabilities. Therefore, the programming of these interfaces must be performed remotely from a digital handsetwhich is then applied to the assignedinterface port.
PAGE 8
EXHIBrrc FCC 10: CDG-ARTU MAGNASTAR C-2000 DIGITAL AIRBORNE TELEPHONE SYSTEM supported. Follow the stepsbelow to program a CDBR-2 port configured as a PC station to treat an incoming ground to air call as either a Voice, FAX, or TDD call. Begin a Remote Program session as shC*n on prior page. Select + ~ nea..Enter Your Passc~ Enter pas.code + --> Select 1 station --~ «ibin ~ .. -->. Choice. will be shaded . cockpit Uplink Voice TDD OK Clear >+ -->* >1 ->3 --->! Go Back >t 7.