User's Manual
Table Of Contents
- 0 General
- 1 BASIS SETTINGS TO USE THIS RADAR
- 2 OPERATING INSTRUCTION
- 2.1 Radar Operation
- 2.2 Set to Operation
- 2.3 Display Organization and Submenu Structure
- 2.3.1 Sensitivity Controls
- 2.3.1.1 Gain and Clutter Processing
- 2.3.1.2 Tune
- 2.3.1.3 Gain
- 2.3.1.4 Sea
- 2.3.1.5 Rain Rate
- 2.3.1.6 Automatic Clutter Reduction
- 2.3.1.7 Filtering Rain Clouds FTC
- 2.3.1.8 Search and Rescue Transponder SART ON/OFF
- 2.3.1.9 Pulse Width Selection (only available in Master mode)
- 2.3.1.10 Interference Selection IR ON/OFF
- 2.3.1.11 Echo Expansion EXP. ON/OFF
- 2.3.2 Radar Video Displays
- 2.3.3 Radar Video Settings
- 2.3.4 Navigational Elements MAP, PIL, EBL and VRM
- 2.3.5 Cursor Information
- 2.3.6 Cursor in Park Position
- 2.3.7 Information Panel
- 2.3.1 Sensitivity Controls
- 2.4 Select Target Information TGT INFO
- 2.5 Target Menu
- 2.6 Zone Management
- 2.7 Function Menu
- 2.7.1 Select the Backlight Menu Brightness Control and Color Palette
- 2.7.2 Select T-SCE (ON/OFF)
- 2.7.3 Select Route (Option)
- 2.7.4 Select Zoom Menu
- 2.7.5 Select Sector Blanking (ON/OFF)
- 2.7.6 System Clear
- 2.7.7 Performance Monitor (PMU)
- 2.7.8 Magnetron Current
- 2.7.9 Test Alert
- 2.7.10 Senc Menu
- 2.7.11 Chart Info
- 2.8 Chart Radar Function
- 2.9 Select ARPA Trial Manoeuvre
- 2.10 Sea Scout (Option)
- 2.11 Alarm and Warning messages and handling
- 2.12 Working Around the Radar Antenna
- 3 Theory of Operation
- 4 Index
Synapsis Radar
with Nautoscan NX Pedestal
Operator Manual
4265.DOC020102
2-100
Edition July 2015
Operator controls
Task
Bearing / distance and toggle field with slider
Depending on the toggle field, the bearing (EBL) or the
distance (VRM) can be edited by moving the slider (Figure
2-34).
Bearing / distance with Operator Panel
This alternative method of operation allows the
EBL1/VRM1 function to be displayed or adjusted quickly.
Pressing the toggle switch releases the rotary knobs for
the operation.
Turn the knob slowly, the VRM/EBL changes/turns in 1
steps.
Turn the knob quickly, the VRM/EBL changes/turns in 10
steps.
The EBL and VRM status LEDs light up.
The EBL/VRM is always placed at your own position.
Parallel movement is not possible when using the
Operator Panel. Adjust the EBL/VRM rotary knobs to
change the bearing (EBL) or the variable range marker
(VRM).
The variable range marker is directly linked to the range
rings (RNG) and adapted accordingly on the display.
2.3.4.7 Deactivating EBL and VRM
The EBL/VRM displays can be hidden by selecting the toggle field again.
Position the cursor on the desired toggle field.
Press the left trackball button.